help with timings kingston 24GB hiperx T1 1600 mhz DDR3

gozy88 · Jun 26, 2013

i have kingston 24GB hiperx T1 1600 mhz DDR3 and mobo Asus p6t deluxe, intel i7 980x Extreme........ i have a problem :heink:

!!! ok i enable the X.M.P in bios and set timings 9.9.9.27.t1 AND voltage 1.5 and ram vol 1.66 and enter windows no problem and suddenly blue screen or frezzee!!! i also try another timing 8.8.8.22, 8.8.8.24 etc... i put the clock 1333 mhz in bios and nothing... i am tired and sick of this,,, please someone help me..... :bounce:

Tradesman1 · Jun 26, 2013

Try CR at 2T instead of 1T, and may want to raise DRAM voltage + 0.05..give that a try

gozy88 · Jun 26, 2013

Tradesman1 :

ok i using right now 9.9.9.27 2t dram 1.72???? as you say tradesman1 and waiting!

gozy88 · Jun 26, 2013

Tradesman1 :

the best timming until now was 133 mhz and 8.8.8.22 t1 DRAM 1.66 but only works fine like 30 min and freeezee and bluescreen

Tradesman1 · Jun 26, 2013

If it running OK now?

gozy88 · Jun 26, 2013

Tradesman1 :

ok i put DRAM core voltage 1.35 and Dram bus voltage 1.72 and the pc run for 30 min and frezzee 9.9.9 27 t2

still frezee mate

Tradesman1 · Jun 26, 2013

DRAM voltage to 1.7, put DRAM BUS voltage back to AUTO

gozy88 · Jun 26, 2013

Tradesman1 :

Ok i will try that right now... and the timmings?? 9.9.9 27 2T are alright???

Tradesman1 · Jun 26, 2013

Correct, give it a shot, I'll be around another 15 minutes or so, then not back until the AM

gozy88 · Jun 26, 2013

Tradesman1 :

kk im running right now that config 9.9.9.27 T2 Dram core voltage 1.7 and Dram voltage auto 5 min and waiting...

Tradesman1 · Jun 26, 2013

Glad to hear, if continues OK for awhile can prob close this out...If anything else, I'll be back in about 5 or so hours, going to grab some shuteye

gozy88 · Jun 26, 2013

Tradesman1 :

and crash again... bluescreen...... :-/: (

Tradesman1 · Jun 26, 2013

Alright, now take QPI/DRAM voltage to 1.3

gozy88 · Jun 26, 2013

Tradesman1 :

stable a loot better right now i am 1.36 and no frezzee issues... waiting some crash to get 1.3 :bounce:

we can do it!!!

Tradesman1 · Jun 26, 2013

All right, have to get some sleep will check back in AM

gozy88 · Jun 26, 2013

Tradesman1 :

thank you for all the help! i was crazy... lol and trying very high voltage... i see the secret in low voltage.. i will try lower voltage right now 1.38 is winning

gozy88 · Jun 26, 2013

Tradesman1 :

okk!!!!!!!!!! 1.38 crash too but was better than 1.7.... i am trying 1.3!! and waiting :sarcastic:

gozy88 · Jun 26, 2013

Tradesman1 :

DRam 1.3 was stable... but crash.. i got bluescreen from hell... i change timing 8.8.8.24 T2.. Dram 1.3 and waiting i am a little sad and tired of this.....

gozy88 · Jun 26, 2013

ok my last try of today 8.8.8.22 2T DRAM VOLT. 1.3.....

gozy88 · Jun 26, 2013

Tradesman1 :

well i am back now trying 1.375 at 9.9.9. 24 2T :sarcastic:

gozy88 · Jun 26, 2013

horrible clash.. back to 9.9.9. 27 2T DRAM 1.36 and waiting :-/

gozy88 · Jun 26, 2013

crash

gozy88 · Jun 27, 2013

Tradesman1 :

where are you i need help!!! :bounce:

gozy88 · Jun 27, 2013

ok i put 1066 mhz 6.6.6.18..... DRAM AUTO and i get rocksolid!! but my memory is 1600 mhz.. i want someone to help me...

Tradesman1 · Jun 27, 2013

Been out working, just take it up slowly 1333 7-7-7-21 and raise MC and DRAM voltage as needed, then on up to 1600

help with timings kingston 24GB hiperx T1 1600 mhz DDR3

Honorable

Legenda in Aeternum

Honorable

Honorable

Legenda in Aeternum

Honorable

Legenda in Aeternum

Honorable

Legenda in Aeternum

Honorable

Legenda in Aeternum

Honorable

Legenda in Aeternum

Honorable

Legenda in Aeternum

Honorable

Honorable

Honorable

Honorable

Honorable

Honorable

Honorable

Honorable

Honorable

Legenda in Aeternum

Share this page