BSOD after win7 reinstall

Martin Cienciala · Jul 14, 2013

Hello, I´ve got a problem with my laptop. I got asus ux32vd, I changed the RAM, old: 2+2, new 2+8. But that was about half a year ago. About week ago my laptop started BSODing, so I installed new clean version on my C drive, while in old win7 because my laptop has only usb 3.0 and it won´t find my usb flash drive while in ?DOS?. Then I deleted the old version. But BSODing continued, I don´t know what to do with it... Safe mode works fine. Should I upload minidump here? Thanks a lot!

smorizio · Jul 14, 2013

Did you install the mb chipset drivers for the laptop??? Have you tried running memtest on the ram???

Martin Cienciala · Jul 14, 2013

I didn´t install any drivers so far. Didn´t know it could BSOD after reinstall, I thought that every vital driver is already present in Win7(I´m not good with PCs), so that it should work even if there are no asus drivers installed. I checked RAM about a month ago and it was ok, right now I´m checking HD, after that I will check RAM again... if everything will be ok, i will install drivers and if that won´t help, i will write here. thanks!

apache_lives · Jul 14, 2013

chipset drivers not installed does not mean a BSOD that stupid

so what your saying is it was blue screening and after a reinstall it still is?

TEST YOUR HARDWARE

HN123 · Jul 14, 2013

Hi, first of all, provide the BSOD (Blue Screen) error data (at least the error code and its parameters).

Best Regards.

Martin Cienciala · Jul 14, 2013

Here is minidump file http://uloz.to/xPeqA4U8/071413-24882-01-dmp , C drive seems ok...

apache_lives · Jul 14, 2013

BSOD codes also mean absolutely nothing - what code do you think a bad psu will spit?

nothing "seems" ok do it right test it thoroughly

Martin Cienciala · Jul 16, 2013

Alright guys, I reinstalled the Winows. Now through bios, on formated disk. Downloaded almost every driver and installed. Everything was tinky winky until yesterday. During movie watching, my laptop went to sleep, and today when I woke up I tried to wake him up too. Didn´t respond, So I turned him off, and BSOD and errors about not finding HDD again! What do you think? Now, after restarting few times, it is running ok again.

HN123 · Jul 16, 2013

Hi, one more time, to start solving some BSOD problem, you must provide the BSOD error code at least.
(not dump file!)
There is only one way...
Best Regard.

apache_lives · Jul 16, 2013

TEST YOUR HARDWARE OR PROVIDE A BSOD CODE

LISTEN TO THE ADVICE YOUR GIVEN HERE

Martin Cienciala · Jul 26, 2013

Hardware tested - nothing found, BSODing began again code is almost everytime STOP: 0x000000F4 (0x0000000000000003, 0xFFFFFA800D1E7060, 0xFFFFFA800D1E7340, 0xFFFFF80002F93350). What to do?

smorizio · Jul 26, 2013

Start With hdtune read your hard drive smart info for warnings. Run a hard drive vendor test tool. Run memtest86 from a boot disk.

Martin Cienciala · Jul 26, 2013

Alright hd tune installed. Where do I find this smart info? In Health section in hd tune I have got an attention in Interface CRC Error Count? What does it mean?

HN123 · Jul 30, 2013

Martin Cienciala :

Hi, for possible solution of your problem review the following:
http://hardwarenavigator.com/Operating%20Systems/Windows/Troubleshooting/BSOD/0x000000F4.html
Best regards.

gamerk316 · Jul 30, 2013

Bug Check 0xF4: CRITICAL_OBJECT_TERMINATION

This indicates that a process or thread crucial to system operation has unexpectedly exited or been terminated.

In this case, its a process crashing [first error code of a 3].

Could be a number of things; lets narrow them down a bit.

1: Run memtest86+. Could be bad RAM [though I'd expect other error codes to pop up as well; checking doesn't hurt].
2: Check the HDD connections [a loose cable can do this intermittently] and run a chkdsk.

Next time you BSOD, note the file that crashes. If its a .dll, it could help us narrow the focus. Also, download BlueScreenView and post ALL the BSOD codes [no need to repeat the same code multiple times; just want to see if any other errors are getting thrown, or just 0xF4].

Martin Cienciala · Aug 5, 2013

Thanks for helping! Can´t run memtest86+ ... because my laptop doesn´t have cd reader and my usbs are all 3.0, so they need to be in win7 os to work properly. Isn´t there any alternative?

Search

BSOD after win7 reinstall

Martin Cienciala

Honorable

HN123

smorizio

Titan

Martin Cienciala

Honorable

apache_lives

Splendid

HN123

Honorable

Martin Cienciala

Honorable

apache_lives

Splendid

Martin Cienciala

Honorable

HN123

Honorable

apache_lives

Splendid

Martin Cienciala

Honorable

smorizio

Titan

Martin Cienciala

Honorable

HN123

Honorable

gamerk316

Glorious

Martin Cienciala

Honorable

TRENDING THREADS

Latest posts

Moderators online

Share this page