High CFM / Quiet Fans for Switch 810 Case - Advice Needed

Zorton

Honorable
May 18, 2013
26
0
10,540
Hey All,

Looking for advice from anyone with really good air cooling knowledge.
Just bought a NZXT Switch 810 MAtte Black finish case to upgrade from my Zalman Z11 Plus.
I wanted to add more fans, have more space, add a 2nd GPU and try my hand at a proper Watercocling loop in the near future so went with this case as it ticked all the boxes.

To start with, my CPU (AMD FX8350) with CM 212 EVO on idle is around 35 Deg Cel and goes to 55deg Cel whilst playing games (BF3, FC3, etc). Thats in the current case with ambient temps over here in Ireland at around 20deg C.

My Asus GTX 660ti is idling at 33deg C and hitting 72deg C whilst playing games.

I know these are fine and within parameters, but I want to OC my CPU to at least 4.6GHz and I want to tweak my GPU as well.

That brings me to the 810 case purchase. I will eventually try a WC CPU loop and add a 2nd 660ti but not till after Xmas.

SO I want to keep my CM 212 EVO in place for now but want to cool things down in my new case.


Therefore, I am looking for powerful (yet Quiet Fans) - High CFM, if possible?

Want to configure the new case as follows:-

1. - 3 * 120mm Fans on the TOP for Exhaust

2. - 2 * 140mm Fans at front for Intake

3. - 1 * 140mm at bottom for Intake

4. - 1 * 140 mm at back for exhaust

5. - Want to replace the 2 120mm Fans on CM 212 EVO with something more powerful than stock.

6. - Will take out bottom HDD Bay (wont be used) and possibly add another Fan to the other detachable HDD bay ?

7. Gonna add 2 Fan Controllers (NZXT Sentry Mesh) to control all fans including the 2 attached to the CM EVO 212 CPU Cooler

I am happy enough with this config, but want to get good air pressure to decrease current temps and give me space to OC comfortably.

I have looked at the Noctuas but all comments I read always refer to how quiet they are..I would like quiet but want high CFM. Using the fan controllers should allow me to set them to full when playing games and reduce when doing less streful activites.

Thanks in advance for all your suggestions in relation to Fans
 
Solution
It´s always the same problem: Noise vs CFM/pressure. Just can´t have both. ;)


My usual advices are:
For quiet fans: Corsair AF series, BeQuiet SilentWings2 or pretty much any AF optimized Noctua fan.
For fans with more power (and more noise): Top class fans from Thermaltake or Scythe.

Also, you didn´t mention if you need LED fans or good lookings fans or anything. But since you mentioned the Noctuas, I suppose you don´t care too much about that. ;)



As for your question about Noctua fans: I only have two pressure optimized fans and I was really surprised at how much air they move at almost no sound.

And if nothing else, you just have to compare the manufacturer´s CFM and noise values. ;)

Som3one

Honorable
Jun 13, 2013
719
0
11,160
It´s always the same problem: Noise vs CFM/pressure. Just can´t have both. ;)


My usual advices are:
For quiet fans: Corsair AF series, BeQuiet SilentWings2 or pretty much any AF optimized Noctua fan.
For fans with more power (and more noise): Top class fans from Thermaltake or Scythe.

Also, you didn´t mention if you need LED fans or good lookings fans or anything. But since you mentioned the Noctuas, I suppose you don´t care too much about that. ;)



As for your question about Noctua fans: I only have two pressure optimized fans and I was really surprised at how much air they move at almost no sound.

And if nothing else, you just have to compare the manufacturer´s CFM and noise values. ;)
 
Solution

Zorton

Honorable
May 18, 2013
26
0
10,540


Thanks for the reply,

As you guessed, not concerned with looks as looking primarily to reduce temps.

I like the Noctua fans and they get great reviews, but from looking at specs online, they average 30 – 54.3 CFM on the 120mm fans.

I was looking more at the following fans for 120mm and 140mm:-

120mm

Akasa Viper S-Flow 120 PWM, 9 Blade
Rated 600~1900rpm, 83.63cfm max, 28.9dbA max
Rated 12VDC, 0.17A, Hydro Dynamic Bearing
4 pin M/B connector, Blk Sleeved

Cooljag Everflow 120mm R121225BU, 9 Blade
Rated 2400rpm, 110.03cfm, 39.5dbA
Rated 12VDC, 0.40A
4 pin M/B connector, No Sleeve

Scythe Slip Stream120, 9 Blade
Rated 1900rpm, 110.31cfm, 37dbA
Rated 12VDC, 0.53A,
3 pin M/B connector, No Sleeve

Aero Cool Shark 12cm Black Edition, 15 blade
Rated 1500rpm (+/-10%), 82.6cfm, 26.5dbA
Rated 12VDC, 0.30A, 3.6W, Fluid Dynamic Bearing
3 pin M/B connector, Blk Sleeved


140mm

Scythe Slip Stream140, 9 Blade
Rated 1700rpm, 92.4cfm, 36.4dbA
Rated 12VDC, 0.35A, Sleeve Bearing
3 pin M/B connector, No Sleeve

Akasa Viper S-Flow 14cm PWM, 9 Blade
Rated 600~1600rpm, 110.61cfm, 26.01dbA
Rated 12VDC, 0.32A, Hydro Dynamic Bearing
4 pin M/B connector, Blk Sleeved

Aero Cool Shark 14cm White Edition, 15 Blade
Rated 1500rpm(+/-10%), 96.5cfm, 29.6dbA
Rated 12VDC, 0.39A, 1.8W, Fluid Dynamic Bearing
3 pin M/B connector, Blk Sleeved


BitFenix Spectre Pro BFF-LPRO-14025B-RP Blue LED, 9 Blade
Rated 1200rpm(+/-10%), 86.73cfm(+/-10%), 22.8dbA
Rated 12VDC, 0.25A(+/-10%), Fluid Dynamic Bearing
3 pin M/B connector, No Sleeve

Found these on Toms Hardware.
The Akaska Viper seem to have a strong CFM at reasonable RPM and get good reviews.
Obviously Yellow is not a preferred colour scheme, but what can you do.

Combination of these fans with the NZXT Fan Controllers should help (I hope) to reduce temps Substantially.

Just undecided :pt1cable: