No output from HD4600

Toggle sidebar Toggle sidebar
R

rallerboy888

Honorable
Oct 10, 2013
7
0
10,510
Hi guys.
So, I'm running a system with a 4670k, M6 Impact and 8GB Ballistix Tactical. I had trouble when I did my first boot, since I got no video output from the iGPU. I bought a GeForce 210, and it output the signal just fine. I discovered that the BIOS was set to use PCIe as default, so I didn't think more of it.
My return period for the 210 is almost expired, so I decided to check if I could run off of the iGPU again. No. Signal. Whatsoever. I have no clue why this is the case. I changed the setting in BIOS and all, but still nothing. Any suggestions on what might be the case?

Thanks.
Oh btw, I'll be purchasing an R9 290 in a month or so. The iGPU is just a replacement until then.
 
Sort by date Sort by votes
smorizio

smorizio

Titan
Jan 22, 2010
30,984
9
125,315
on the mb bios make sure muilt monitor turned on under the primany display line. if not the ipgpu wont turn on when a gpu is plugged in. in windows did you install the intel video drivers for the ipgpu or did windows install them and under device managers does it show up?? if it not there then it could be a bent pin on the mb under the cpu or a bad cpu.
 
Upvote 0 Downvote
R

rallerboy888

Honorable
Oct 10, 2013
7
0
10,510


I didn't remove the 210, if that's what you mean. Would that make a difference?
 
Upvote 0 Downvote
R

rallerboy888

Honorable
Oct 10, 2013
7
0
10,510


The iGPU does not show up in Device Manager. When I installed my CPU, I made sure that no pins were bent. Should I take the board out, and remove the CPU? Just to be sure, I mean. I ran Prime95 for a couple of hours, and it seemed to run fine.
I didn't remove the 210 when I tried using the iGPU. Should I do that? I didn't enable the multi-monitor setting either. I assumed that it was unnecessary, since the iGPU was set as the main output.
 
Upvote 0 Downvote
R

rallerboy888

Honorable
Oct 10, 2013
7
0
10,510


I'll just try removing the 210 then, and see if it works. The nVidia driver constantly crashes too...
 
Upvote 0 Downvote
R

rallerboy888

Honorable
Oct 10, 2013
7
0
10,510


Okay, so I removed the 210 after configuring the BIOS. Still getting no signal. I get perfectly fine signal with the same HDMI cable through the 210, but none through the motherboard. Instead, I get the Q-Code "B2" whatever that means...
 
Upvote 0 Downvote
MiDNiGHTsoul

MiDNiGHTsoul

Honorable
Oct 1, 2013
144
0
10,760


Try reseting your BIOS and then enabling the iGPU through the BIOS.
B2 state is 'Console Output/Input devices/Console initialization and Load Option ROM (VGA, RAID, parallel ports, serial ports)'

 
Upvote 0 Downvote
R

rallerboy888

Honorable
Oct 10, 2013
7
0
10,510


Wait, so shut down the PC > reset BIOS on the I/O switch > connect HDMI to motherboard > view BIOS through GeForce 210 > set to iGPU > reboot/continue?
 
Upvote 0 Downvote
MiDNiGHTsoul

MiDNiGHTsoul

Honorable
Oct 1, 2013
144
0
10,760
[/quotemsg]

Wait, so shut down the PC > reset BIOS on the I/O switch > connect HDMI to motherboard > view BIOS through GeForce 210 > set to iGPU > reboot/continue?[/quotemsg]

Yes.
You cant access BIOS with while the 210 is not on the pc?
 
Upvote 0 Downvote
R

rallerboy888

Honorable
Oct 10, 2013
7
0
10,510


Wait, so shut down the PC > reset BIOS on the I/O switch > connect HDMI to motherboard > view BIOS through GeForce 210 > set to iGPU > reboot/continue?[/quotemsg]

Yes.
You cant access BIOS with while the 210 is not on the pc?
[/quotemsg]

Well, I don't know if it's accesible, since I can't get any video output. I assume it's running in the back ground, but I don't know for sure.
 
Upvote 0 Downvote
You must log in or register to reply here.

TRENDING THREADS

Latest posts

Moderators online

Share this page

COMPANY
RESOURCES
FOLLOW
Top Bottom