hello everyone. i am upgrading to water cooling. reason being, i have an htpc case. the thing is cramped. shit for airflow. i have a 3570k and gtx 780 that heat up this case to a level im not comfortable. and im thinking that watercooling, given the lack of aiflow, will benefit me and my system. and so i have questions. below is the list of parts i have found/want/think i need. please advise if things can be done better or cheaper
my case is an antec nsk 2480 btw. so in theory all this should fit. but i still need to make a prototype and mockup estimated measurements
list:
EK-Supremacy Clean CSQ [3830046990808]
$84
http://www.ekwb.com/shop/ek-supremacy-clean-csq.html
EK-FC Titan SE - Nickel (Original CSQ) [3831109868324]
$140
http://www.ekwb.com/shop/ek-fc-titan-se-original-csq-nickel.html
EK-FC Titan SE Backplate - Black [3831109868331]
$36
http://www.ekwb.com/shop/ek-fc-titan-se-backplate-black.html
EK-BAY DCP 2.2 Combo Unit (incl. pump) [3831109840627]
$128
http://www.ekwb.com/shop/ek-bay-dcp-2-2-combo-unit-incl-pump.html
radiator [ex-rad-315]
$50
http://www.frozencpu.com/products/14327/ex-rad-315/XSPC_EX240_Dual_120mm_Low_Profile_Split_Fin_Radiator.html
Scythe Gentle Typhoon AP-15 (1850rpm) [4571225042459]
$20x2
http://www.ekwb.com/shop/scythe-gentle-typhoon-ap-15-1850rpm.html
EK-12mm (1/2") G1/4 High-Flow Fitting [3830046996015]
x6 $3
http://www.ekwb.com/shop/fitting-1-2-id.html
TUBE PrimoChill PrimoFlex™ Advanced LRT™ 19,1 / 12,7 mm - Crystal Clear RETAIL 3m [3831109850664]
$33
http://www.ekwb.com/shop/tube-primochill-primoflextm-advanced-lrttm-19-1-12-7-mm-crystal-clear-retail-3m.html
EK-Ekoolant Blood RED (premix 1000mL) [3830046999610]
$10
http://www.ekwb.com/shop/ek-ekoolant-blood-red-premix-1000ml.html
i feel like there has got to be a cheaper way to do this. also i will probably be switching to an mITX board to make for more room. and, if you were to google images of the case, will probably be cutting out the wall that seperates the hard drive area to make more room too. will be hiding the hard drives elsewhere and using that whole side of the case for whatever needs to go there.
in short, my questions are:
is there a cheaper way to do this or is it going to be individual parts like this?
does all this seem compatible?
is there anything else i need?
thanks for any help given!
anyways anyone have any further advice for this build or does this all look good? basically im learning as im going.
thanks everyone
my case is an antec nsk 2480 btw. so in theory all this should fit. but i still need to make a prototype and mockup estimated measurements
list:
EK-Supremacy Clean CSQ [3830046990808]
$84
http://www.ekwb.com/shop/ek-supremacy-clean-csq.html
EK-FC Titan SE - Nickel (Original CSQ) [3831109868324]
$140
http://www.ekwb.com/shop/ek-fc-titan-se-original-csq-nickel.html
EK-FC Titan SE Backplate - Black [3831109868331]
$36
http://www.ekwb.com/shop/ek-fc-titan-se-backplate-black.html
EK-BAY DCP 2.2 Combo Unit (incl. pump) [3831109840627]
$128
http://www.ekwb.com/shop/ek-bay-dcp-2-2-combo-unit-incl-pump.html
radiator [ex-rad-315]
$50
http://www.frozencpu.com/products/14327/ex-rad-315/XSPC_EX240_Dual_120mm_Low_Profile_Split_Fin_Radiator.html
Scythe Gentle Typhoon AP-15 (1850rpm) [4571225042459]
$20x2
http://www.ekwb.com/shop/scythe-gentle-typhoon-ap-15-1850rpm.html
EK-12mm (1/2") G1/4 High-Flow Fitting [3830046996015]
x6 $3
http://www.ekwb.com/shop/fitting-1-2-id.html
TUBE PrimoChill PrimoFlex™ Advanced LRT™ 19,1 / 12,7 mm - Crystal Clear RETAIL 3m [3831109850664]
$33
http://www.ekwb.com/shop/tube-primochill-primoflextm-advanced-lrttm-19-1-12-7-mm-crystal-clear-retail-3m.html
EK-Ekoolant Blood RED (premix 1000mL) [3830046999610]
$10
http://www.ekwb.com/shop/ek-ekoolant-blood-red-premix-1000ml.html
i feel like there has got to be a cheaper way to do this. also i will probably be switching to an mITX board to make for more room. and, if you were to google images of the case, will probably be cutting out the wall that seperates the hard drive area to make more room too. will be hiding the hard drives elsewhere and using that whole side of the case for whatever needs to go there.
in short, my questions are:
is there a cheaper way to do this or is it going to be individual parts like this?
does all this seem compatible?
is there anything else i need?
thanks for any help given!
anyways anyone have any further advice for this build or does this all look good? basically im learning as im going.
thanks everyone