Hey everyone, so I recently moved over to win8.1 and I moved my storage drive over from my old rig. Windows is giving me the old "windows detected a harddrive error" so I did a dskchk and came up with no errors, segatetools failed on smart and short DST but passed short and long generic test.
I ended up running HDDscan and the smart results gave me
001 Raw Read Error Rate 100 100 0000000000-0004 051
002 Throughput performance 056 056 0000000000-1083 000
003 Spin Up Time 001 001 0000000000-84D9 025
004 Start/Stop Count 096 096 0000000000-119C 000
005 Reallocation Sector Count 252 252 0000000000-0000 010
007 Seek Error Rate 252 252 0000000000-0000 051
008 Seek time Perfomance 252 252 0000000000-0000 015
009 Power-On Hours Count 100 100 0000000000-38C8 000
010 Spin Retry Count 252 252 0000000000-0000 051
011 Recalibration Retries 252 252 0000000000-0000 000
012 Device Power Cycle Count 100 100 0000000000-009D 000
191 G-sense Rate/Servo tracking 252 252 0000000000-0000 000
192 Emergency Retract Count 252 252 0000000000-0000 000
194 HDA Temperature 064 060 26 C 000
194 HDA Temperature Maximum 064 060 40 C 000
194 HDA Temperature Minimum 064 060 11 C 000
195 Hardware ECC Recovered 100 100 0000000000-0000 000
196 Reallocation Event Count 252 252 0000000000-0000 000
197 Current Pending Errors Count 252 252 0000000000-0000 000
198 Uncorrectable Errors Count 252 252 0000000000-0000 000
199 UltraDMA CRC Errors 200 200 0000000000-0000 000
200 Write Error Rate 100 100 0000000000-0000 000
223 Load Retry Count 252 252 0000000000-0000 000
225 Load Cycle Count 100 100 0000000000-119E 000
Basically only the spin up time was giving me an error... It's a storage drive so it's not always spinning. Is this an issue or can I just ignore it?
I ended up running HDDscan and the smart results gave me
001 Raw Read Error Rate 100 100 0000000000-0004 051
002 Throughput performance 056 056 0000000000-1083 000
003 Spin Up Time 001 001 0000000000-84D9 025
004 Start/Stop Count 096 096 0000000000-119C 000
005 Reallocation Sector Count 252 252 0000000000-0000 010
007 Seek Error Rate 252 252 0000000000-0000 051
008 Seek time Perfomance 252 252 0000000000-0000 015
009 Power-On Hours Count 100 100 0000000000-38C8 000
010 Spin Retry Count 252 252 0000000000-0000 051
011 Recalibration Retries 252 252 0000000000-0000 000
012 Device Power Cycle Count 100 100 0000000000-009D 000
191 G-sense Rate/Servo tracking 252 252 0000000000-0000 000
192 Emergency Retract Count 252 252 0000000000-0000 000
194 HDA Temperature 064 060 26 C 000
194 HDA Temperature Maximum 064 060 40 C 000
194 HDA Temperature Minimum 064 060 11 C 000
195 Hardware ECC Recovered 100 100 0000000000-0000 000
196 Reallocation Event Count 252 252 0000000000-0000 000
197 Current Pending Errors Count 252 252 0000000000-0000 000
198 Uncorrectable Errors Count 252 252 0000000000-0000 000
199 UltraDMA CRC Errors 200 200 0000000000-0000 000
200 Write Error Rate 100 100 0000000000-0000 000
223 Load Retry Count 252 252 0000000000-0000 000
225 Load Cycle Count 100 100 0000000000-119E 000
Basically only the spin up time was giving me an error... It's a storage drive so it's not always spinning. Is this an issue or can I just ignore it?
Facebook
Twitter
Instagram