New Build, booted yesterday, then stopped

Toggle sidebar Toggle sidebar
T

terrigo

Honorable
Dec 27, 2013
5
0
10,510
Hi, this is my first build. Yesterday I was able to boot, installed Windows, added drivers. It didn't recognize my graphics card so I was unable to install that driver. Windows was finishing installing all of the updates and the computer was restarted. Now it won't Boot and there is no signal to the monitor. The case doesn't have a speaker and I don't believe the mobo does either. I have never had any beeps. I have already gone through all of the steps in the no boot, no post, no beep thread to no avail. And YES the 8 pin CPU power cable is plugged in. The fans and LED's are on on the case, HS, and video card. Here are my components:

As Rock H87 Pro4
i7-4770k LGA 1150
EVGA GEFORCE GTX780 ACX
Corsair HX850 PSU
Hyper 212 EVO Cooler
Antec 1200 Case
Corsair Vengenance (2 x4gb) DDR3
Seagate 1TB SATA 3
Asus 24xDVD

I am at a loss since it seemed that everything was good initially.
 
Solution
tyranthoth
ok if everything spins up and there are no beeps and it appears everything is working on the board/system but you are still getting no video than something is wrong in the video arena. Maybe video card, Maybe Video Settings in Bios, Maybe video cable, or monitor itself. Since you've done driver updates, remove the hdd and see if you can get into the bios from the vga port on the MoB, if successful try from the GPU with the hdd disconnected, make sure the Bios is configured correctly for the video If this is also successful reconnect hdd, if it fails after connecting hdd then it's windows that glitching on you boot from CD/USB and reload system. If it fails from the start than replace your cable, try a different monitor. If it fails from...
Sort by date Sort by votes
T

terrigo

Honorable
Dec 27, 2013
5
0
10,510


I've tried it with the video card out, installed with and with out the power connected to it. I have power to fans and LED's. I've tried no RAM, moving it to all of the different slots and repeating the process with both sticks. The fan on the video card and heat sink both run as do the case fans. Since there doesn't seem to be an onboard speaker I don't know if there were ever any beeps. Before shutting down yesterday Windows was installed and I was able to get online...Now I have a blank monitor via VGA saying "no signal". The monitor I have doesn't support HDMI.
 
Upvote 0 Downvote
T

terrigo

Honorable
Dec 27, 2013
5
0
10,510


I've given up for the night :( I've got everything disconnected but tomorrow I'll start again. Before I disconnected everything the HDD did start up.
 
Upvote 0 Downvote
tyranthoth

tyranthoth

Distinguished
Dec 10, 2011
176
0
18,760
ok if everything spins up and there are no beeps and it appears everything is working on the board/system but you are still getting no video than something is wrong in the video arena. Maybe video card, Maybe Video Settings in Bios, Maybe video cable, or monitor itself. Since you've done driver updates, remove the hdd and see if you can get into the bios from the vga port on the MoB, if successful try from the GPU with the hdd disconnected, make sure the Bios is configured correctly for the video If this is also successful reconnect hdd, if it fails after connecting hdd then it's windows that glitching on you boot from CD/USB and reload system. If it fails from the start than replace your cable, try a different monitor. If it fails from GPU and BIOS settings are correct RMA (return and replace) the GPU. If all fails RMA the MoB
 
Upvote 0 Downvote
Solution
You must log in or register to reply here.

TRENDING THREADS

Latest posts

Moderators online

Share this page

COMPANY
RESOURCES
FOLLOW
Top Bottom