Cooler Master Hyper t4 installation on AMD

pugno50 · Jul 14, 2014

Hi, can anyone tell me how to install, step by step, the cm hyper t4 in a cm k380, m5a99x evo r2.0, fx 8320, corsair vengeance materials?

Also, i've a question:

-I have to install it vertically, where do i put the fan ?

In youtube i found very little, so i ask to you! I know that i'll have disable dual channel, ok...
Thanks

coolcole01 · Jul 14, 2014

you wont have to disable just put the ram in the second and fourth slot take the fan off before you try to install it the fan goes on top

coolcole01 · Jul 14, 2014

basically take the fan off ,make sure your ram is in, plug the fan in then set the fan to the side make a pea sized plop of paste, take the radiator and slide the bracket through the bottom there will be a metal bar in the middle that will rest in the center of the bottom of the heatsink. clip the top in first then use the lever to press tight then attach fan to top side of the radiator

damric · Jul 14, 2014

T4 just clips onto the AMD mobo bracket. Pretty easy. Slather the grease on those heat pipe gaps. Mount the fan on bottom and have it blow upwards. RAM clearance wasn't an issue for me.

coolcole01 · Jul 14, 2014

if you look at the piece of paper that came with it the fan is on the top but i doubt it really matters

damric · Jul 14, 2014

coolcole01 :

Mine was all in Chinese so I discarded it

Beta test sample...

pugno50 · Jul 14, 2014

I didn't undestand much damric. Sorry

coolcole01 · Jul 14, 2014

hahahaha the horrible thing is i feel like a dork quoting instructions when i almost never use them

damric · Jul 14, 2014

pugno50 :

Just look at the picture:

Now monkey see, monkey do.

damric · Jul 14, 2014

coolcole01 :

Guilty of that myself. I'm a hypocrite since I scold people here for not reading thier mobo manuals.

coolcole01 · Jul 14, 2014

but i will admit that i read my sabertooth 990fx r2.0 back to front 20 times and im on my fifth read through of my extreme6

pugno50 · Jul 14, 2014

Noo i didn't understand how to install blackplate, screws, and the next... thanks for the help i love you toms hw guys <3

coolcole01 · Jul 14, 2014

you dont need to install any backplate installs to the stock bracket

pugno50 · Jul 14, 2014

What sto

damric · Jul 14, 2014

pugno50 :

Yeah all that crap is for Intel mobo. All you need is to clip it onto the plastic AMD mobo fitting that is already there.

coolcole01 · Jul 14, 2014

clips on just like the stock cooler

pugno50 · Jul 14, 2014

So i say you what i do :

1- take the box and open it with knife or a katana
2- take the cooler and the termal grease
3- place the cooler in the 4 holes near the AMD socket (lol)
4- (don't i need to screws it or do smthing?)
5- termal grease
6- fan 7- connection!
Finish ?

coolcole01 · Jul 14, 2014

there are no screw holes just the bracket that comes with the board it was what the stock cooler attached to the mobo then basically take the fan off ,make sure your ram is in, plug the fan in then set the fan to the side make a pea sized plop of paste, take the radiator and slide the bracket through the bottom there will be a metal bar in the middle that will rest in the center of the bottom of the heatsink. clip the top in first then use the lever to press tight then attach fan to top side of the radiator

pugno50 · Jul 14, 2014

In the manual it's mentioned the retention bracket for intel and for amd. So i have to use the bracket for amd.?

coolcole01 · Jul 14, 2014

yes it will be the longest bracket with one end that bends down with a square and a second that has a little lever that at the bottom also has a square this goes through the bottom there will be little grooves for it. the little metal piece in the middle will hold it in place

pugno50 · Jul 14, 2014

So basically i have to just set the retention bracket of AMD that came with the cooler with the heatsink itself ? Ah and i have corsair vengenace high profile ram so i think it wont fot

coolcole01 · Jul 14, 2014

i have high profile gskill ram and it fit

pugno50 · Jul 14, 2014

Reading again your past comment i think i understood... i have to use the brackets that came with the manual and attach it in the middle bottom gap like the 212 evo , then turn right the lever like the manual and thats'all ?

coolcole01 · Jul 14, 2014

you got it bud just make sure the little metal piece in the middle is in the center groove and your gold

pugno50 · Jul 14, 2014

Hyper t4 is for my friend... post-tomorrow i have to build at him him pc! My pc will have hyper 212 evo! Coolcole01 thanks for the help and the time you and damric have dedicated to me! Now i can be sure of what will i do .. just select yourbest answer! Thanks

Cooler Master Hyper t4 installation on AMD

Reputable

Splendid

Splendid

Illustrious

Splendid

Illustrious

Reputable

Splendid

Illustrious

Illustrious

Splendid

Reputable

Splendid

Reputable

Illustrious

Splendid

Reputable

Splendid

Reputable

Splendid

Reputable

Splendid

Reputable

Splendid

Reputable

Share this page