PC Specs:
CPU: Intel Core i7 2700K (no overclock)
MB: Sabertooth Z77
RAM: 16 GB Corsair Vengeance (1600mhz)
Sound: Creative Soundblaster X-fi Fatality
Monitor: My 46" Samsung TV 1080p
The new parts I bought was EVGA Supernova G2 1000w replacing my Thermaltake smart M 850w.
R9 295x2 replacing my crossfired 6950's. and I bought the Corsair H100i for my CPU.
I installed all the parts and it would start booting and I got the single beep. After the MB splash screen my tv was losing signal and never gaining it back. the 295x2 doesn't have hdmi ports but it has a mini display to hdmi adapter I was using that but I swapped for the DVI to hdmi and I was able to boot up normally once. it takes awhile to get to the beep too. The MB has sensors to check all the parts inside and it does this a few times before beeping.
I can boot into safe mode and safe mode with networking fine but cant boot up normally. I unplugged everything that was unnecessary. Sound card, cam, headset, a fan, my backup hard drive. After I did this the windows repair prompt came up I did that and I finally got a normal boot all the colors were wonky purple pinkish I downloaded the new drivers and was able to fix the color inside catalyst control after a clean restart.
This was all early morning working on it yesterday. Today I got a a long beep and three short beeps which is the graphics card. But It didn't happen again so far.
It sounds and looks like a power issue or the graphics card itself is bad to me. Hopefully not its 1000 dollars and I want to rip through games with it. There is an article that a 1000w is running two 295x2 I don't believe all my other parts consume up to a second 295x2 and if it did it obviously should run anyway.
I need some help solving this not sure on what to do. Thanks!
**UPDATE**
I forgot to mention I updated the bios before I got a clean boot. Also, I just swapped my 295x2 with one of my previous 6950's and It went through a tiny loop of powering on and off until it booted up cleanly I shut down and tried it again and booted fine.
So does this mean I have to RMA my 295x2? Could there be another issue as well? Insight would be much appreciated!
CPU: Intel Core i7 2700K (no overclock)
MB: Sabertooth Z77
RAM: 16 GB Corsair Vengeance (1600mhz)
Sound: Creative Soundblaster X-fi Fatality
Monitor: My 46" Samsung TV 1080p
The new parts I bought was EVGA Supernova G2 1000w replacing my Thermaltake smart M 850w.
R9 295x2 replacing my crossfired 6950's. and I bought the Corsair H100i for my CPU.
I installed all the parts and it would start booting and I got the single beep. After the MB splash screen my tv was losing signal and never gaining it back. the 295x2 doesn't have hdmi ports but it has a mini display to hdmi adapter I was using that but I swapped for the DVI to hdmi and I was able to boot up normally once. it takes awhile to get to the beep too. The MB has sensors to check all the parts inside and it does this a few times before beeping.
I can boot into safe mode and safe mode with networking fine but cant boot up normally. I unplugged everything that was unnecessary. Sound card, cam, headset, a fan, my backup hard drive. After I did this the windows repair prompt came up I did that and I finally got a normal boot all the colors were wonky purple pinkish I downloaded the new drivers and was able to fix the color inside catalyst control after a clean restart.
This was all early morning working on it yesterday. Today I got a a long beep and three short beeps which is the graphics card. But It didn't happen again so far.
It sounds and looks like a power issue or the graphics card itself is bad to me. Hopefully not its 1000 dollars and I want to rip through games with it. There is an article that a 1000w is running two 295x2 I don't believe all my other parts consume up to a second 295x2 and if it did it obviously should run anyway.
I need some help solving this not sure on what to do. Thanks!
**UPDATE**
I forgot to mention I updated the bios before I got a clean boot. Also, I just swapped my 295x2 with one of my previous 6950's and It went through a tiny loop of powering on and off until it booted up cleanly I shut down and tried it again and booted fine.
So does this mean I have to RMA my 295x2? Could there be another issue as well? Insight would be much appreciated!
Facebook
Twitter
Instagram