How to use two seperate wifi connections at the same time.
Tags:
- Connection
-
WiFi
- Wireless Network
Last response: in Wireless Networking
samuelmason
October 5, 2014 12:18:05 PM
Is it possible to get two wifi adapters and connect to two different wifi signals and take advantage of both at the same time? I'd like to do some streaming which I have enough to do on a single connection. But if I want to play a multiplayer game it cannot handle both at the same time. So perhaps I could use one connection to stream and another to game on the same computer?
I still haven't purchased my second adapter so I'd like to confirm if this is even possible before doing so. Also does it matter if I have the exact same 2 adapters? would there be driver issues? I'm not really sure how that would work.
Thank you!
I still haven't purchased my second adapter so I'd like to confirm if this is even possible before doing so. Also does it matter if I have the exact same 2 adapters? would there be driver issues? I'm not really sure how that would work.
Thank you!
More about : seperate wifi connections time
-
Reply to samuelmason
Tom Tancredi
October 5, 2014 1:11:31 PM
NO. And No. And No.. on everything here.
If your connection can't handle BOTH multiplayer and streaming then you need a better Internet connection. It isn't the WIFI that is the problem, it is the CONNECTION to the router; think this way, you can do 100MPH out of your driveway, but if the Road to your driveway is only 5MPH it doesn't matter how many 'driveways' (wifi adapters) you put on your house (computer) your still only 5MPH to get to the store (streaming music / multiplayer game).
If your connection can't handle BOTH multiplayer and streaming then you need a better Internet connection. It isn't the WIFI that is the problem, it is the CONNECTION to the router; think this way, you can do 100MPH out of your driveway, but if the Road to your driveway is only 5MPH it doesn't matter how many 'driveways' (wifi adapters) you put on your house (computer) your still only 5MPH to get to the store (streaming music / multiplayer game).
-
Reply to Tom Tancredi
m
0
l
samuelmason
October 5, 2014 4:15:41 PM
Tom Tancredi said:
NO. And No. And No.. on everything here. If your connection can't handle BOTH multiplayer and streaming then you need a better Internet connection. It isn't the WIFI that is the problem, it is the CONNECTION to the router; think this way, you can do 100MPH out of your driveway, but if the Road to your driveway is only 5MPH it doesn't matter how many 'driveways' (wifi adapters) you put on your house (computer) your still only 5MPH to get to the store (streaming music / multiplayer game).
You misunderstand me, I'm not connecting to the same router/internet line. Both are entirely different lines from 2 seperate internet providers.
-
Reply to samuelmason
m
0
l
Related resources
- How to use two internet connection at same time using lan and wi-fi - Forum
- Connect to two different routers (using two seperate ethernet ports) at the same time - Forum
- How to use two internet connection at same time using lan and wi-fi - Forum
- How to use two Internet Connections at the same time ? - Forum
- How to connect two wifi network at same time - Forum
sla70r
October 5, 2014 4:37:29 PM
Best solution
bill001g
October 5, 2014 5:59:21 PM
If you have 2 different ISP it can be done but it gets very messy. First be sure they do not use the same subnet for the lan.
The key problem you have is you are only allowed to have a single default route. If you allow multiple interfaces to get a default router the pc will still select one based on metric.
So step 1 is to only allow the default route on the connection you wish to use for your main internet connection. You can ether put a static IP on the secondary wireless nic or your can use the ROUTE DELETE command to remove the 0.0.0.0 route that points to the second wireless gateway.
Now the hard part. What you will need to do is get a list of IP addresses that you want to use the second connection. You then put in ROUTE ADD commands for those ip blocks and set the gateway ip of the secondary internet connection. This tends to be very tedious. Since the connection will get different IP addresses depending on which ISP connection they take you really need to make sure you get all the server ip. For example if you were to login into a game company login server from one IP and then attempt access the game server via the other IP the gaming company would detect that as issue and likely disconnect you. Making this even worse many sites use akamai to balance servers so the same DNS name can map to multiple IP and they can change from time to time. Keeping up with a akamai based site is lots of work.
They do make dual wan router and there is some load balancing pc software but they all have the same issue. You have to tell it somehow the relationship between server IP addresses that require them to be sourced from the same IP. This is not something a program can know and there are not lists of these relationships.
If you can come up with a very narrow list of function and servers you want to use the second connection you will have best chance of success.
The key problem you have is you are only allowed to have a single default route. If you allow multiple interfaces to get a default router the pc will still select one based on metric.
So step 1 is to only allow the default route on the connection you wish to use for your main internet connection. You can ether put a static IP on the secondary wireless nic or your can use the ROUTE DELETE command to remove the 0.0.0.0 route that points to the second wireless gateway.
Now the hard part. What you will need to do is get a list of IP addresses that you want to use the second connection. You then put in ROUTE ADD commands for those ip blocks and set the gateway ip of the secondary internet connection. This tends to be very tedious. Since the connection will get different IP addresses depending on which ISP connection they take you really need to make sure you get all the server ip. For example if you were to login into a game company login server from one IP and then attempt access the game server via the other IP the gaming company would detect that as issue and likely disconnect you. Making this even worse many sites use akamai to balance servers so the same DNS name can map to multiple IP and they can change from time to time. Keeping up with a akamai based site is lots of work.
They do make dual wan router and there is some load balancing pc software but they all have the same issue. You have to tell it somehow the relationship between server IP addresses that require them to be sourced from the same IP. This is not something a program can know and there are not lists of these relationships.
If you can come up with a very narrow list of function and servers you want to use the second connection you will have best chance of success.
-
Reply to bill001g
Share
Tom Tancredi
October 5, 2014 6:57:39 PM
samuelmason said:
Tom Tancredi said:
NO. And No. And No.. on everything here. If your connection can't handle BOTH multiplayer and streaming then you need a better Internet connection. It isn't the WIFI that is the problem, it is the CONNECTION to the router; think this way, you can do 100MPH out of your driveway, but if the Road to your driveway is only 5MPH it doesn't matter how many 'driveways' (wifi adapters) you put on your house (computer) your still only 5MPH to get to the store (streaming music / multiplayer game).
You misunderstand me, I'm not connecting to the same router/internet line. Both are entirely different lines from 2 seperate internet providers.
To me this sounds SUSPICIOUSLY like your sucking off two 'neighbors' Wifis, because no business / personal home would have "two different wifi signals " to "2 seperate internet providers." That is overly costly and makes no sense. So I am calling a flag on that.
To simplify what Bill001g is saying below:
NO. Think of Wifi or Wired connection like a cell phone in your hand. While you can hold one cell phone to one ear and talk to Person A, you can physically hold # 2 cellphone to the second ear to talk to Person B the problem is when all three of you all talk. When both A and B both talk at the same time you can't tell who is saying what, and conversely when you 'speak' both A and B think your talking to them separately. So communications break down very quickly and you can't hold the 'conversation'. SAME THING for Windows, it can't talk to just ONE Wifi, and it can't understand when both Wifi talk to it at the same time. Much less WHO is actually talking as both say the same 'name' (I am Wifi, speak to me).
As for the Router-multiple connection, basically at that point your trying to "load Balance" (as he said) and getting very technical / high risk of failures with trying to 'force' a third seperate device to do the work your asking (and are very COSTLY) then cable connect that to your PC (no you couldn't redistribute the two wifi signals as wifi signals, that means you have to have ACCESS to both router's Admin functions and setup things as AP/Repeater Bridges).
-
Reply to Tom Tancredi
m
0
l
samuelmason
October 6, 2014 2:58:06 PM
Tom Tancredi said:
samuelmason said:
Tom Tancredi said:
NO. And No. And No.. on everything here. If your connection can't handle BOTH multiplayer and streaming then you need a better Internet connection. It isn't the WIFI that is the problem, it is the CONNECTION to the router; think this way, you can do 100MPH out of your driveway, but if the Road to your driveway is only 5MPH it doesn't matter how many 'driveways' (wifi adapters) you put on your house (computer) your still only 5MPH to get to the store (streaming music / multiplayer game).
You misunderstand me, I'm not connecting to the same router/internet line. Both are entirely different lines from 2 seperate internet providers.
To me this sounds SUSPICIOUSLY like your sucking off two 'neighbors' Wifis, because no business / personal home would have "two different wifi signals " to "2 seperate internet providers." That is overly costly and makes no sense. So I am calling a flag on that.
To simplify what Bill001g is saying below:
NO. Think of Wifi or Wired connection like a cell phone in your hand. While you can hold one cell phone to one ear and talk to Person A, you can physically hold # 2 cellphone to the second ear to talk to Person B the problem is when all three of you all talk. When both A and B both talk at the same time you can't tell who is saying what, and conversely when you 'speak' both A and B think your talking to them separately. So communications break down very quickly and you can't hold the 'conversation'. SAME THING for Windows, it can't talk to just ONE Wifi, and it can't understand when both Wifi talk to it at the same time. Much less WHO is actually talking as both say the same 'name' (I am Wifi, speak to me).
As for the Router-multiple connection, basically at that point your trying to "load Balance" (as he said) and getting very technical / high risk of failures with trying to 'force' a third seperate device to do the work your asking (and are very COSTLY) then cable connect that to your PC (no you couldn't redistribute the two wifi signals as wifi signals, that means you have to have ACCESS to both router's Admin functions and setup things as AP/Repeater Bridges).
First of all, I'm not "leeching" off anyone. I have a very unique situation which is why I came here to ask this question. Second of all I did mention in my post that I wanted to use each connection for a seperate task. As in I don't want to use both connections to load the same youtube video. Thirdly, your simplification of bill001g seems off and I want to thank him for not making assumptions and letting me know of the possibilities and limitations of such task.
Perhaps my initial post was poorly written which led you to these assumptions. Either way thanks but no thanks!
-
Reply to samuelmason
m
0
l
samuelmason
October 6, 2014 5:44:47 PM
Tom Tancredi said:
NO. And No. And No.. on everything here. If your connection can't handle BOTH multiplayer and streaming then you need a better Internet connection. It isn't the WIFI that is the problem, it is the CONNECTION to the router; think this way, you can do 100MPH out of your driveway, but if the Road to your driveway is only 5MPH it doesn't matter how many 'driveways' (wifi adapters) you put on your house (computer) your still only 5MPH to get to the store (streaming music / multiplayer game).
http://speedify.com/press/
"Toms Hardware - Even a single stream such as a Netflix movie can be split between two or three Internet connections for a higher resolution and faster buffering"
Have a nice day!
-
Reply to samuelmason
m
0
l
bill001g
October 6, 2014 7:03:16 PM
This is a massively complex topic that will take quite a bit to give you even a hint of the problems. Speedify can only partially solve this issue the only way to truly do this is to put hardware appliance on both ends. They can easily solve the issue of traffic you send since they have a server but traffic you receive is much harder since you machine and your routers are involved.
So the first major issue is you must send all the traffic to a remote location via a vpn. This eats bandwidth because of the packet overhead but it also add quite a bit a latency because you data must go though some remote data center that may no be in the optimum path to the servers.
So the VPN solves the issue of the different IP.
The problem is you now get a problem that is almost as bad. If the ISP connections are not very closely matched in latency to the VPN center the packets get out of order. Out of order packets are detected as packet loss by the end applications. They will ask to have packets retransmitted which increases the utilization with trash and if it gets bad enough it will drop the session. This is almost impossible to solve, they must buffer large amounts of data and deliver it in bursts. You trade increased latency for bandwidth.
There are huge white papers that you can find discussing the issue of load balancing by packet on links with different speeds and latencies. It quickly gets into topics like splitting larger packets so all packets take the same delivery time. If were as simple as buying speedify companies like riverbed would never be able to sell hardware appliances that do this for $50,000 per end.
You can try speedify but I would not expect much especially if you are trying to combine say a mobile broadband connection and a cable modem. The differences in the latency require huge buffers to avoid out of order data.
Their other software dispatch is basically a fancy version of the route commands. If you let it attempt to load balance by session counts or round robin you will quickly run into the issue of accessing the same server from both IP addresses. When you open a web page there are massive numbers of session being opened and many times these have dependencies on coming from the same IP address. So you can use this rather than the route commands, it is a little easier to configure but it is not some magic software. If you let it try to load balance on its own you will quickly find web sites that do not work as you would expect.
So the first major issue is you must send all the traffic to a remote location via a vpn. This eats bandwidth because of the packet overhead but it also add quite a bit a latency because you data must go though some remote data center that may no be in the optimum path to the servers.
So the VPN solves the issue of the different IP.
The problem is you now get a problem that is almost as bad. If the ISP connections are not very closely matched in latency to the VPN center the packets get out of order. Out of order packets are detected as packet loss by the end applications. They will ask to have packets retransmitted which increases the utilization with trash and if it gets bad enough it will drop the session. This is almost impossible to solve, they must buffer large amounts of data and deliver it in bursts. You trade increased latency for bandwidth.
There are huge white papers that you can find discussing the issue of load balancing by packet on links with different speeds and latencies. It quickly gets into topics like splitting larger packets so all packets take the same delivery time. If were as simple as buying speedify companies like riverbed would never be able to sell hardware appliances that do this for $50,000 per end.
You can try speedify but I would not expect much especially if you are trying to combine say a mobile broadband connection and a cable modem. The differences in the latency require huge buffers to avoid out of order data.
Their other software dispatch is basically a fancy version of the route commands. If you let it attempt to load balance by session counts or round robin you will quickly run into the issue of accessing the same server from both IP addresses. When you open a web page there are massive numbers of session being opened and many times these have dependencies on coming from the same IP address. So you can use this rather than the route commands, it is a little easier to configure but it is not some magic software. If you let it try to load balance on its own you will quickly find web sites that do not work as you would expect.
-
Reply to bill001g
m
0
l
NetEssence
October 8, 2014 10:03:51 AM
samuelmason said:
Is it possible to get two wifi adapters and connect to two different wifi signals and take advantage of both at the same time? I'd like to do some streaming which I have enough to do on a single connection. But if I want to play a multiplayer game it cannot handle both at the same time. So perhaps I could use one connection to stream and another to game on the same computer? I still haven't purchased my second adapter so I'd like to confirm if this is even possible before doing so. Also does it matter if I have the exact same 2 adapters? would there be driver issues? I'm not really sure how that would work.
Thank you!
You can bond two, three or even four ADSL lines using a special router. Installation is quick and easy. We recently deployed this solution for a client who could not get high speed broadband but who needed greater capacity.
The routers that can support this are Netgear DGN 1000 (2 bonded lines) and Power Router Pro 3-4 bonded lines).
Once you have greater capacity, you can stream over a faster WiFi router; perhaps consider using an 802.11ac router.
The fact that we can do this in the UK implies that it can be done in the US.
-
Reply to NetEssence
m
0
l
NetEssence
October 8, 2014 11:49:08 PM
bill001g said:
NetEssence said:
samuelmason said:
Is it possible to get two wifi adapters and connect to two different wifi signals and take advantage of both at the same time? I'd like to do some streaming which I have enough to do on a single connection. But if I want to play a multiplayer game it cannot handle both at the same time. So perhaps I could use one connection to stream and another to game on the same computer? I still haven't purchased my second adapter so I'd like to confirm if this is even possible before doing so. Also does it matter if I have the exact same 2 adapters? would there be driver issues? I'm not really sure how that would work.
Thank you!
You can bond two, three or even four ADSL lines using a special router. Installation is quick and easy. We recently deployed this solution for a client who could not get high speed broadband but who needed greater capacity.
The routers that can support this are Netgear DGN 1000 (2 bonded lines) and Power Router Pro 3-4 bonded lines).
Once you have greater capacity, you can stream over a faster WiFi router; perhaps consider using an 802.11ac router.
http://www.net-essence.com/broadband-and-voip/broadband...
The fact that we can do this in the UK implies that it can be done in the US.
Don't you know it actually makes you look foolish when you come to a site and and try to advertise your product when a end user can't even think to buy this. Maybe you should tell him to buy a VDSL router or maybe a super high speed fiber router.
You can put all the fancy bonding equipment you want on your side of the connection if the ISP does not offer that as a service then it will do nothing. And of course if they do offer the service it will not be for free.
A ISP can put in anything you are willing to pay for but it is not some go the store and buy something and all your problems are solved.
Hi,
I am not trying to sell anything as I believe the OP is in the US and we are in the UK.
The ISP does not need to support line bonding - the bonding is done by the routers that I mentioned above. I mentioned the models so that anybody seeing this post can go out and buy the routers or do further research for themselves.
The link is only intended to provide some additional information.
-
Reply to NetEssence
m
0
l
bill001g
October 9, 2014 12:16:41 AM
NetEssence said:
bill001g said:
NetEssence said:
samuelmason said:
Is it possible to get two wifi adapters and connect to two different wifi signals and take advantage of both at the same time? I'd like to do some streaming which I have enough to do on a single connection. But if I want to play a multiplayer game it cannot handle both at the same time. So perhaps I could use one connection to stream and another to game on the same computer? I still haven't purchased my second adapter so I'd like to confirm if this is even possible before doing so. Also does it matter if I have the exact same 2 adapters? would there be driver issues? I'm not really sure how that would work.
Thank you!
You can bond two, three or even four ADSL lines using a special router. Installation is quick and easy. We recently deployed this solution for a client who could not get high speed broadband but who needed greater capacity.
The routers that can support this are Netgear DGN 1000 (2 bonded lines) and Power Router Pro 3-4 bonded lines).
Once you have greater capacity, you can stream over a faster WiFi router; perhaps consider using an 802.11ac router.
http://www.net-essence.com/broadband-and-voip/broadband...
The fact that we can do this in the UK implies that it can be done in the US.
Don't you know it actually makes you look foolish when you come to a site and and try to advertise your product when a end user can't even think to buy this. Maybe you should tell him to buy a VDSL router or maybe a super high speed fiber router.
You can put all the fancy bonding equipment you want on your side of the connection if the ISP does not offer that as a service then it will do nothing. And of course if they do offer the service it will not be for free.
A ISP can put in anything you are willing to pay for but it is not some go the store and buy something and all your problems are solved.
Hi,
I am not trying to sell anything as I believe the OP is in the US and we are in the UK.
The ISP does not need to support line bonding - the bonding is done by the routers that I mentioned above. I mentioned the models so that anybody seeing this post can go out and buy the routers or do further research for themselves.
The link is only intended to provide some additional information.
You are posting your company in order to advertise business why else would you do it. You could post links to routers or whatever.
I will be very blunt then. You are a fool if you think you can just buy some magic router and it bond the circuits. If you are such a expert now explain how these magic routers can solve the problem of having 2 different ip addresses and send packets for the same session over both. How do you make this work when it is a fundamental violation of how tcpip works. You have no clue do you if you think the ISP does not need to be involved.
You did not even read the post where this was discusses.
Now I can just laugh at you for posting a company link and showing then showing how skilled you really are.;
-
Reply to bill001g
m
0
l
NetEssence
October 9, 2014 12:39:19 AM
bill001g said:
NetEssence said:
bill001g said:
NetEssence said:
samuelmason said:
Is it possible to get two wifi adapters and connect to two different wifi signals and take advantage of both at the same time? I'd like to do some streaming which I have enough to do on a single connection. But if I want to play a multiplayer game it cannot handle both at the same time. So perhaps I could use one connection to stream and another to game on the same computer? I still haven't purchased my second adapter so I'd like to confirm if this is even possible before doing so. Also does it matter if I have the exact same 2 adapters? would there be driver issues? I'm not really sure how that would work.
Thank you!
You can bond two, three or even four ADSL lines using a special router. Installation is quick and easy. We recently deployed this solution for a client who could not get high speed broadband but who needed greater capacity.
The routers that can support this are Netgear DGN 1000 (2 bonded lines) and Power Router Pro 3-4 bonded lines).
Once you have greater capacity, you can stream over a faster WiFi router; perhaps consider using an 802.11ac router.
http://www.net-essence.com/broadband-and-voip/broadband...
The fact that we can do this in the UK implies that it can be done in the US.
Don't you know it actually makes you look foolish when you come to a site and and try to advertise your product when a end user can't even think to buy this. Maybe you should tell him to buy a VDSL router or maybe a super high speed fiber router.
You can put all the fancy bonding equipment you want on your side of the connection if the ISP does not offer that as a service then it will do nothing. And of course if they do offer the service it will not be for free.
A ISP can put in anything you are willing to pay for but it is not some go the store and buy something and all your problems are solved.
Hi,
I am not trying to sell anything as I believe the OP is in the US and we are in the UK.
The ISP does not need to support line bonding - the bonding is done by the routers that I mentioned above. I mentioned the models so that anybody seeing this post can go out and buy the routers or do further research for themselves.
The link is only intended to provide some additional information.
You are posting your company in order to advertise business why else would you do it. You could post links to routers or whatever.
I will be very blunt then. You are a fool if you think you can just buy some magic router and it bond the circuits. If you are such a expert now explain how these magic routers can solve the problem of having 2 different ip addresses and send packets for the same session over both. How do you make this work when it is a fundamental violation of how tcpip works. You have no clue do you if you think the ISP does not need to be involved.
You did not even read the post where this was discusses.
Now I can just laugh at you for posting a company link and showing then showing how skilled you really are.;
If it makes you feel better, I have removed the link from my original post.
Now, go and read the FAQs here - http://www.sharedband.com/solutions/faq - and you will learn that line bonding is really quite simple.
In future, please don't insult people who know more than you and preferably, don't post any more on this site. Your comments are not helpful for people who are looking for useful advice.
-
Reply to NetEssence
m
0
l
ib2007
October 9, 2014 12:57:47 AM
The only time i've seen 2 different outside links connected to a network were adsl and they were connected in such a way if one goes down router then reroutes through second for redundancy. I don't believe you can link various sources together into a single link. If you have it documented please share here i'd love to read all about it.
-
Reply to ib2007
m
0
l
bill001g
October 9, 2014 1:01:44 AM
NetEssence said:
bill001g said:
NetEssence said:
bill001g said:
NetEssence said:
samuelmason said:
Is it possible to get two wifi adapters and connect to two different wifi signals and take advantage of both at the same time? I'd like to do some streaming which I have enough to do on a single connection. But if I want to play a multiplayer game it cannot handle both at the same time. So perhaps I could use one connection to stream and another to game on the same computer? I still haven't purchased my second adapter so I'd like to confirm if this is even possible before doing so. Also does it matter if I have the exact same 2 adapters? would there be driver issues? I'm not really sure how that would work.
Thank you!
You can bond two, three or even four ADSL lines using a special router. Installation is quick and easy. We recently deployed this solution for a client who could not get high speed broadband but who needed greater capacity.
The routers that can support this are Netgear DGN 1000 (2 bonded lines) and Power Router Pro 3-4 bonded lines).
Once you have greater capacity, you can stream over a faster WiFi router; perhaps consider using an 802.11ac router.
http://www.net-essence.com/broadband-and-voip/broadband...
The fact that we can do this in the UK implies that it can be done in the US.
Don't you know it actually makes you look foolish when you come to a site and and try to advertise your product when a end user can't even think to buy this. Maybe you should tell him to buy a VDSL router or maybe a super high speed fiber router.
You can put all the fancy bonding equipment you want on your side of the connection if the ISP does not offer that as a service then it will do nothing. And of course if they do offer the service it will not be for free.
A ISP can put in anything you are willing to pay for but it is not some go the store and buy something and all your problems are solved.
Hi,
I am not trying to sell anything as I believe the OP is in the US and we are in the UK.
The ISP does not need to support line bonding - the bonding is done by the routers that I mentioned above. I mentioned the models so that anybody seeing this post can go out and buy the routers or do further research for themselves.
The link is only intended to provide some additional information.
You are posting your company in order to advertise business why else would you do it. You could post links to routers or whatever.
I will be very blunt then. You are a fool if you think you can just buy some magic router and it bond the circuits. If you are such a expert now explain how these magic routers can solve the problem of having 2 different ip addresses and send packets for the same session over both. How do you make this work when it is a fundamental violation of how tcpip works. You have no clue do you if you think the ISP does not need to be involved.
You did not even read the post where this was discusses.
Now I can just laugh at you for posting a company link and showing then showing how skilled you really are.;
If it makes you feel better, I have removed the link from my original post.
Now, go and read the FAQs here - http://www.sharedband.com/solutions/faq - and you will learn that line bonding is really quite simple.
In future, please don't insult people who know more than you and preferably, don't post any more on this site. Your comments are not helpful for people who are looking for useful advice.
I am very helpful you are the newcomer to this forum that just post links he does not even understand himself. If you had been around for a while you would know my qualification...or do I have to post my CCIE numbers for you to learn.
Your post saying you can just buy some magic router to solve this and then you post a link to a service that likely is using a form of VPN bonding shows you have no clue at all. So now I have to buy a special router and then buy a service from a provider. This is not actual bonding in the way that term is normally used.
This was clearly discussed that you could use a similar product called speedify and why that has limitations many of which are actually documented in the site you link.
If you had posted discussion then maybe I would not be so aggressive in my comments toward you. Too many people do google search and post the results not knowing anything about what they actually found. The worst offenders post links to products or companies they represent.
-
Reply to bill001g
m
0
l
Related resources
- How to Connect to Wi-fi and Ethernet at the same time using Linksys E900 Router Forum
- Can I use the speed from two networks at the same time (ethernet and wifi)? Forum
- Solvedhow to use Two IPs on one computer in the same time Forum
- How to use two different ips at same time Forum
- How to use two internet connections in same pc for different browsers Forum
- SolvedHow do I connect two routers together to use the same network Forum
- SolvedHow to create seperate networks for home and business use, both with wired connections. VPN HELP? Forum
- possible to use tata photon+ dongle and wifi connection at the same time Forum
- HOW TO USE 2 DIFFRENT CONNECTIONS AT THE SAME TIME? Forum
- How to connect two lan conections together and work at same time Forum
- Solvedtwo network connections at the same time?? Forum
- SolvedCan i have two internet connections at the same time? Forum
- How to bond two seperate DSL connections to create one faster internet Forum
- How to connect to two networks at the same time.? Forum
- Two routers, two seperate wifi networks - one internet connection Forum
- More resources
Read discussions in other Wireless Networking categories
!