New RAM oc'ing issue? HELP!!!
- Thread starter H. Finner
- Start date
I just got my new ram and here it is: http://www.newegg.com/Product/Product.aspx?Item=N82E16820104520
So I replace it with my old ones which were 2x4gb Corsair vengeance 1800mhz. Everything starts up fine, it says hardware has been changed... I go to setup to overclock as i follow the instructions here:
https://m.youtube.com/watch?v=w4sx-GuY3CA
Not 100% sure about my timings so I just put it on auto. Then I put my frequency to DDR3-2400 and my voltage to 1.65V. I then restart with all of my saved settings...
It turns on but no display and i don't see my GPU running. So then I restart and then it works and says, previous configurations could not be saved.
So I go back into bios and try every kind of voltage all the way down to 1.5V and restarting every time. I finally just put voltage on auto and STILL SAYS THE SAME THING. When I put back all settings back to default + OC Genie it works... I'm so confused... Help!!!!
Full specs:
Motherboard: http://www.newegg.com/Product/Product.aspx?Item=N82E16813130754
Power Supply: http://www.amazon.com/XFX-Series-Certified-Active-P1750GTS3X/dp/B00JNBGNGM#customerReviews
Processor: AMD A10-5800k
HDD: http://www.amazon.com/WD-Blue-Desktop-Hard-Drive/dp/B0088PUEPK/ref=sr_1_1?ie=UTF8&qid=1419626458&sr=8-1&keywords=HDD
RAM: http://www.newegg.com/Product/Product.aspx?Item=N82E16820104520
GPU: http://www.amazon.com/Gigabyte-GDDR5-4GB-2xDVI-Graphics-GV-R927XOC-4GD/dp/B00H707TIW/ref=sr_1_3?ie=UTF8&qid=1419626762&sr=8-3&keywords=r9+270x+4gb
So I replace it with my old ones which were 2x4gb Corsair vengeance 1800mhz. Everything starts up fine, it says hardware has been changed... I go to setup to overclock as i follow the instructions here:
https://m.youtube.com/watch?v=w4sx-GuY3CA
Not 100% sure about my timings so I just put it on auto. Then I put my frequency to DDR3-2400 and my voltage to 1.65V. I then restart with all of my saved settings...
It turns on but no display and i don't see my GPU running. So then I restart and then it works and says, previous configurations could not be saved.
So I go back into bios and try every kind of voltage all the way down to 1.5V and restarting every time. I finally just put voltage on auto and STILL SAYS THE SAME THING. When I put back all settings back to default + OC Genie it works... I'm so confused... Help!!!!
Full specs:
Motherboard: http://www.newegg.com/Product/Product.aspx?Item=N82E16813130754
Power Supply: http://www.amazon.com/XFX-Series-Certified-Active-P1750GTS3X/dp/B00JNBGNGM#customerReviews
Processor: AMD A10-5800k
HDD: http://www.amazon.com/WD-Blue-Desktop-Hard-Drive/dp/B0088PUEPK/ref=sr_1_1?ie=UTF8&qid=1419626458&sr=8-1&keywords=HDD
RAM: http://www.newegg.com/Product/Product.aspx?Item=N82E16820104520
GPU: http://www.amazon.com/Gigabyte-GDDR5-4GB-2xDVI-Graphics-GV-R927XOC-4GD/dp/B00H707TIW/ref=sr_1_3?ie=UTF8&qid=1419626762&sr=8-3&keywords=r9+270x+4gb
TRENDING THREADS
-
Question should i put the new 3050 lp in a sff hp g3?- Started by jordanbuilds1
- Replies: 14
-
-
-
-
-
Facebook
Twitter
Instagram