Can my PSU power this monster graphics card?

kir13y

Reputable
Jul 21, 2014
135
0
4,690
I am thinking of getting a Nvidia EVGA 980 TI graphics card. I currently have a 875W PSU (I think and I will check tomorrow and update). I currently have a 750 TI FTW from EVGA and a GTX 480. I have a triple monitor setup and I am currently running the big middle monitor on the 750 and the other two side monitors are on the 480.

So, can I run the 750 and the 980 with my current PSU?
Thanks internet users!!!!
 
Solution


01N03G is the part number for the case not the PSU. You will need to pull the psu out as the sticker with the part number and specs is on the other side of the unit.
The 980 TI only requires a 600w PSU if it's a capable power supply. So yes, the capacity of your current PSU is more than enough. Whether the quality and reliability are sufficient is a different story though. Some units are barely able to provide a portion of their rated capacity, and tend to die quickly under strenuous gaming loads. Even a lot of those sold under well known brand names are junk in reality. The model and internal platform is the key.

What is the model and brand of your 875w PSU?
 


So you're saying if he has an 850w Logisys or Raidmax power supply, you'd recommend it for use with that card? C'mon man. Find out what kind of hardware you're dealing with before instinctively saying yes. Just because a unit says it has 850w doesn't mean it can even provide 450w continuously without exploding, catching fire or just taking out hardware when it dies.

http://www.tomshardware.com/reviews/low-cost-psu-pc-power-supply,2862.html
 

Vighnesh Misal

Honorable
Mar 21, 2013
37
0
10,560


You're absolutely right. I simply assumed he would have one of the popular brands like Antec, Corsair, Seasonic or Cooler Master. But that's no excuse for the sloppiness.
 

kir13y

Reputable
Jul 21, 2014
135
0
4,690


I found an Alienware Aurora R4 for very cheap and I am almost certain that this is the current PSU that is in it: http://www.amazon.com/Genuine-Dell-Precision-Workstation-Compatible/dp/B00BTMT8YC
 
Yeah, I'd NEVER use that, or any other OEM PSU, with a high end discreet card. For a GTX 750 or R7 240, or lower tiered cards, it's probably ok, but not for high end gaming cards. You absolutely want a Tier 1 or Tier 2 unit for use with any high end card.

PSU Tier list: http://www.tomshardware.com/forum/id-2547993/psu-tier-list.html


However, I think maybe that Alienware unit may use a proprietary DELL PSU design, which may not be compatible with standard ATX power supplies. You may be able to find the information needed at the following link. I'll look into it further if I get a chance after while.

http://en.community.dell.com/owners-club/alienware/f/3746/t/19597084
 

bignastyid

Titan
Moderator


That link could be 1 of 3 units, and 2 of the the 3 are not good. The UL number on the W299G has a UL number that points to Delta as the OEM, and Delta is normally a good PSU OEM. However the J556T and U595G are made by Chicony(according to the UL number) and they are not a good OEM. Look at the side of your PSU to confirm the part number. If you have the Delta unit it may work, but with a $650+ video card I'd err on the side of caution and buy a PSU thats known to be good quality and adequate for the system. A good PSU would cost about a 10th of what a the 980ti costs.
 
Also, knowing the part number would certainly allow us to be able to determine it's dimensions and form factor. You might also get the exact part number of the PC unit as a whole, because like I said before, some of those units use a proprietary case and PSU. If yours is such a unit, then a standard ATX PSU is not going to fit in all probability. And depending on what motherboard is installed, if it too is a Dell proprietary motherboard it may not even use a standard 20 or 24 pin power connector.
 
Yeah, that doesn't help. Pictures of the unit's identification label with the model and serial, the power supply label and the connections from the power supply that connect to the motherboard would be helpful, but still may not answer all the questions. These Dell (Alienware) units were never intended to be upgraded. They are intended to be permanent and throw away solutions. Some compatibility on particular models exists, for aftermarket parts, but some models are extremely limited when it comes to form factor considerations and proprietary hardware.
 


Guess you didn't bother to read the rest of the thread. Maybe you should do so next time. It's funny that you're asking for advice on a PSU in another thread, and trying to offer advice about a PSU in this one. This particular power supply is unlikely to be of any reliable quality unless it happens to be the Delta model, which as of yet we do not know.
 

kir13y

Reputable
Jul 21, 2014
135
0
4,690
So, I think the PSU model number is: DP/N 01N03G. It is made by DELL and came installed in my Alienwear Aurora R4. I found this fourm with another guy who has the same PSU and they said that if it has a button on the back then it is the 875W model. Mine has the button on the back so I can confirm that I do have an 875W PSU.

I figured out that my Motherboard model number is: 07jnh0 [Manufacturer: Alienware]

Hope this helps!
 
How many 6, 6+2 or 8 pin PCI power connectors does that power supply have, if any? What are the dimensions of the power supply as I can't seem to find ANY specs on that PSU model. Your motherboard seems to use standard 8 pin and 24pin motherboard power connectors, so that part should be fine IF you end up having to get another power supply.

If your current PSU has the necessary PCI connections for the graphics card then it might be ok to try and use it since it's over spec, but honestly, I wouldn't trust an Alienware or Dell PSU unless it was a Delta model, with my expensive graphics card, any more than I'd trust a Raidmax or Logisys unit. It's probably not as bad as those kinds of units, but I doubt it's anything to write home about either.
 

bignastyid

Titan
Moderator


01N03G is the part number for the case not the PSU. You will need to pull the psu out as the sticker with the part number and specs is on the other side of the unit.
 
Solution

kir13y

Reputable
Jul 21, 2014
135
0
4,690


Alright. I will take it out this weekend and post the PSU part number this weekend if I have time.