Motherboard Problem(Boot problems, OS installation problems, etc.)

Lynden

Honorable
Feb 11, 2014
17
0
10,510
Hello,

I am at my wit's end here. I've been at this for almost 10 hours. I recently built a new PC.(First time). I have the MSi Gaming 5 LGA 1150 Motherboard, Noctua NH-D15, i7 4790k, and a GTX 970. and EVGA 600w PSU.

Edit: forgot to mention that PC will turn on even when shutdown.

I don't know what else to do, I've been searching everywhere on the internet for what my problem might be, but no avail. So I built it normally. Everything's fine, all fans are spinning, drive is detected, RAM is detected, CPU, GPU, etc. Then I tried installing my Windows 7 Ultimate CD (OEM, I have bought a different key of course.) When it says "Windows is preparing files" after that is done it goes to the windows loading boot logo and just reboots/shuts off or fatal error BSOD.


I tried it a few times but it kept doing it and so I re-formatted my SSD because it had another OS on it(I was thinking I could just re-format it with the option when installing a new OS).
Still nothing, getting frustrated at that point I got my Windows 8.1 Installation and it went in fine but it kept shutting itself down when I reached the log-in screen or at the loading screen. I have no idea what to do at that point. I did what people told others from putting 1 slot at a time, loosening the CPU cooler as it might be too tight.(temps were fine 35c idle), Removing the GPU and re-seating it, Resetting CMOS(Removed battery for 20 seconds and put back in).


Still nothing, I even put in my new HDD to see if it worked but it gave the same errors, reboots, etc. What I got from my MOBO's debug code was 61,62, and A2 were all I remembered. Reading my manual it completely skips Code 61 and 62. The nearest number to is 63 which translates to "Late CPU Initialization". After I shut-down my newly-built PC and turned it on a few minutes later. It would just turn on for a few seconds then turn off. Sometimes turning on and turning off a few times. Sometimes it would boot up to the BIOS but I can't really do anything as it would just reboot me when I install an O.S.

TL;DR Can't install OS, PC turns on and off, sometimes can go to BIOS. Giving me error code
61 and sometimes 62. Which translates near at "Late CPU Initialization".



Thank you for the time for reading my extremely frustrating problem and I will be searching for what wrong I might have done for my new PC to act like this.
 
Solution
It's not all that good of a PSU (made by HEC)
http://www.techpowerup.com/reviews/EVGA/600B/11.html

If that turns out to be an issue, ask them to exchange it for the GQ model

But looks like you are making progress ... make sure there weren't any extra MoBo standoffs installed in the case.... was puzzled with a user build and when took the MoBo out immediately saw an extra one that musta been touching something.
I would say that 3 outta 4 times I have seen this problem it has been a RAM issue.

Which EVGA PSU ? Have a PSU tester ? (About $20 on newegg).

Any chance when assembling the PSU, ya got some dirt or goup on contacts ? Worth cleaning all ?

Did you perhaps use too much of TIM that is capocitive ? (AS5)

You should reset CMOS via a jumper on the board as I recall.


If corrupted, BIOS fix is here:
https://www.youtube.com/watch?v=pZ1u9xnSR38

He's copying one to another but you could just d/l to a USB and install

 

Lynden

Honorable
Feb 11, 2014
17
0
10,510
http://www.newegg.com/Product/Product.aspx?Item=N82E16817438014
This EVGA PSU^ Or if you don't want the link the 600B. And no I don't have a PSU tester unfortunately. It could stay on the BIOS though for a long time if that says anything on the PSU.

No, all the connectors are clean.

I used the rice size method and yes it is as5

I tried looking for it, all I found was two pins named "JBAT1" it is directly related to clearing CMOS Jumper. But the instructions on my manual are unclear and short. It has none of the jumper where you can change from slot 1 and 2 to 2 and 3 then back to 1 and 2. It's just 2 pins without a jumper.

Hmm I might try to update my BIOS a bit later. The time and date on the BIOS was 1/1/2013 and 0:52:00. Very outdated.

Will try the last method and see what happens.
 

Lynden

Honorable
Feb 11, 2014
17
0
10,510
So it installed successfully after I removed the motherboard itself out of the case. Didn't error or crash or re-boot. I don't know what's causing it but I will double-check everything.
 
It's not all that good of a PSU (made by HEC)
http://www.techpowerup.com/reviews/EVGA/600B/11.html

If that turns out to be an issue, ask them to exchange it for the GQ model

But looks like you are making progress ... make sure there weren't any extra MoBo standoffs installed in the case.... was puzzled with a user build and when took the MoBo out immediately saw an extra one that musta been touching something.
 
Solution

Lynden

Honorable
Feb 11, 2014
17
0
10,510
Well, I got it all working now. It was probably something that was shorting out the motherboard maybe. Because I took the motherboard out again and just ran it with RAM,Cooler, and CPU. It installed Windows fine without errors, then afterwards I made sure nothing was touching the motherboard in the back of it or any wires. Thanks for your help and advices, man.