I need help on a few poinrs
A] There is a 5 Pin ( yes 5 ) connector called JP12CI [pwr 12C] on the MB, in the manual it says it is"The Power Supply SMBbus 12C Header" , the description later in the manual under connecting cables says ...
Monitors the status of the power supply, fan and system temperature.
Should this be connected,? And if so how? The pin out says .. 1.Clock, 2. Data, 3. power fail, 4. ground, 5. 3.3 V
[ note this is just after a section entitled TPM Header. I think this is some sort of extra thing for remote management stuff]
Its a bit confusing as the manual also covers the X10SRA-F board, in a few places it says "only supported on the X10SRA-F" - but doesn't say that here.
NB there is also a 24 Pin ATX Main powerplug and an 8 Pin CPU Power plug (JPW1 and JPW2) both say they are required, [I understand these ones]. Except the scematic diagram labels JPW2 as a "12V 4 pin CPU power connector, its actually physically an 8 pin, and later in the manual calls it an 8 Pin connector [ I assume its a typo error? ]. I assume I just put together the 2 halves of the 12V 4+4 pin EPS Power connector on the PSU and push them in together
B] there is also another 3 Pin connector called "Standby Power Connector" STBY1. What do I connect that to on the PSU? Or do I ignore it?
On the Supernova 1200. i only have the 24 pin, and 2 x 8 or 4in plus 4pin EPS Power commectors.
C] The MB has a 5V 3 Pin DOM power connector for. Disk on Management device - I Assume I should Ignore this connection?
D] the Supernova comes with a lot of cables. Some connection on the back say VGA or PCIe 6+2 and a few have PCIe 6.
Is the 6 pin block exactly the same as the 6 pin part of the 6+2?
Sorry to ask such basic questions, but the Supernova manual is very basic, and sparse in technical content. In addition all the wires in the cabling are black. And no pin definition is given on the EVGA Manual or case back.
Thanks
A] There is a 5 Pin ( yes 5 ) connector called JP12CI [pwr 12C] on the MB, in the manual it says it is"The Power Supply SMBbus 12C Header" , the description later in the manual under connecting cables says ...
Monitors the status of the power supply, fan and system temperature.
Should this be connected,? And if so how? The pin out says .. 1.Clock, 2. Data, 3. power fail, 4. ground, 5. 3.3 V
[ note this is just after a section entitled TPM Header. I think this is some sort of extra thing for remote management stuff]
Its a bit confusing as the manual also covers the X10SRA-F board, in a few places it says "only supported on the X10SRA-F" - but doesn't say that here.
NB there is also a 24 Pin ATX Main powerplug and an 8 Pin CPU Power plug (JPW1 and JPW2) both say they are required, [I understand these ones]. Except the scematic diagram labels JPW2 as a "12V 4 pin CPU power connector, its actually physically an 8 pin, and later in the manual calls it an 8 Pin connector [ I assume its a typo error? ]. I assume I just put together the 2 halves of the 12V 4+4 pin EPS Power connector on the PSU and push them in together
B] there is also another 3 Pin connector called "Standby Power Connector" STBY1. What do I connect that to on the PSU? Or do I ignore it?
On the Supernova 1200. i only have the 24 pin, and 2 x 8 or 4in plus 4pin EPS Power commectors.
C] The MB has a 5V 3 Pin DOM power connector for. Disk on Management device - I Assume I should Ignore this connection?
D] the Supernova comes with a lot of cables. Some connection on the back say VGA or PCIe 6+2 and a few have PCIe 6.
Is the 6 pin block exactly the same as the 6 pin part of the 6+2?
Sorry to ask such basic questions, but the Supernova manual is very basic, and sparse in technical content. In addition all the wires in the cabling are black. And no pin definition is given on the EVGA Manual or case back.
Thanks