Can't change ink cartridge on epson wf-3640 printer

Toggle sidebar Toggle sidebar
M

missprint

Reputable
Feb 9, 2016
1
0
4,510
Cant get packet of ink cartridges to move over so I can lift cover to change ink. screen says ink low. No matter what button I push screen says operation invalid. I have turned machine off and on, unplugged it,, tried to reset it. nothing
 
Solution
Ralston18
Run a test print via the menu or software. See if the ink cartridge assembly will move out and away from being under the edge of the case.

Watch to see if the ink carridge assembly appears jammed.
Sort by date Sort by votes
Ralston18

Ralston18

Titan
Moderator
Oct 11, 2014
34,894
3,324
146,290
Do you have the manual for your printer?

Here is a link to the manual but verify that it is for your printer:

https://files.support.epson.com/docid/cpd3/cpd39368.pdf

The reason for the manual is that I am not sure what you referring to as "cover".

See pages 242 and 243 of the manual.

You should be lifting the lid and glass"cover together to get access to the carriage holding the cartridges.

As best I can tell there is nothing in the way of lifting/opening the cartridge cover.

Please clarify. Thanks.
 
Upvote 0 Downvote
K

kbsmith

Commendable
May 6, 2016
1
0
1,510
I had the same experience. Epson website doesn't tell you an important step at the very beginning of the process. Before you open the scanner unit cover, you need to start by selecting Setup from the touch screen. Then select Ink Levels. Just below the graphic picture of your ink levels you will see two options, OK and Cartridge(s) Replacement. Select Cartridge(s) Replacement. Your printer will go into cartridge change mode. The touch screen will tell you to open the scanner unit cover. When you open the scanner unit cover, the ink cartridge assembly will have moved out into the middle of the printer, away from the right edge of the printer where you were prevented from opening the cartridge cover. Follow instructions from there at: http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?infoType=FAQ&oid=232592&foid=254104
 
Upvote 1 Downvote
A

Amy_32

Commendable
Sep 7, 2016
1
0
1,510
I have done exactly as described below. Cartridge assembly remains under the edge of the case, doesn't move.



 
Upvote 0 Downvote
A

Ana_27

Commendable
Sep 12, 2016
2
0
1,510
After pressing "Cartridge replacement", a screen shows up that says to press the blue button. Press this, and then it will tell u to lift it up and the cartridges will move.
 
Upvote 0 Downvote
andying

andying

Commendable
Aug 29, 2016
8
0
1,520
Your may try to following trouble shooting for your printer and hope this help

TROUBLESHOOTING

10 simple steps to fix your printer when it can't recognise your new toners.

Printer can't recognise your new cartridge? No worry, we have the solution for you, please follow our 10 simple steps and your printer will back to work!

Please do the following steps:

1) With the Power on machine

2) Take cartridge out Close door. clean the cartridge chip (when applicable) using an alcohol

3) Turn Power off on wall

4) Leave off for three to five minutes

5) Turn power on

6) Engine will run in most printers, when it stops open door.

7) Printer should now be looking for cartridge/s.

8) Reinstall cartridge/s.

9) Close door.

10) Cartridge should be accepted at this point

Reference: http://cheapinks.com.au/cheap-printer-inks/10-simple-steps-to-fix-your-printer-when-it-cannot-recognise-your-new-toners
 
Upvote 0 Downvote
You must log in or register to reply here.

TRENDING THREADS

Latest posts

Moderators online

Share this page

COMPANY
RESOURCES
FOLLOW
Top Bottom