I'm transfering files between 2 linux servers on the same network. This is the Network configuration on both of them:
server 1:
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
MDI-X: on
Supports Wake-on: pumbag
Wake-on: g
Current message level: 0x00000001 (1)
drv
Link detected: yes
server 2:
Settings for eth0: Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
MDI-X: Unknown
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
Both servers connected to the same switch, which supported 1 Gig, with Cat5e / Cat6.
I really don't know what could possibly cause that speed. I've read that maybe the 'auto-negotiation' configure may do it? Can I check what is the negotiated speed then somehow?
I'm using 'rsync -avzh --progress' command. my switch is hp v1910-48g. I also just tried to replace the Cat 5e cable to cat7, same speed.
server 1:
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
MDI-X: on
Supports Wake-on: pumbag
Wake-on: g
Current message level: 0x00000001 (1)
drv
Link detected: yes
server 2:
Settings for eth0: Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
MDI-X: Unknown
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
Both servers connected to the same switch, which supported 1 Gig, with Cat5e / Cat6.
I really don't know what could possibly cause that speed. I've read that maybe the 'auto-negotiation' configure may do it? Can I check what is the negotiated speed then somehow?
I'm using 'rsync -avzh --progress' command. my switch is hp v1910-48g. I also just tried to replace the Cat 5e cable to cat7, same speed.
Facebook
Twitter
Instagram