H100i GTX stops working after pc upgrade.

Dfrer · Jul 13, 2017

Hey guys.
In the past week I've decided to upgrade my cyberpower PC rig, I originally had a 4790k and an ASUS motherboard. I upgraded to a X99 Deluxe and a 5820k, I decided to keep the same cooler as its less than one year old and it seemed to be working just fine. When I finally installed the new motherboard and booted up the pc, my pump was not being picked up in the BIOS (my guess is that it's not getting the full 12v it needs from the CPU_FAN header) not only was that happening but now because none of the heat was being taken away, my CPU started to heat up. Now I have tried some fixes and I've turned it back on a few times to try some things since that happened. If I have to I will replace the part, but I would really prefer not too. Is it dangerous to have the CPU on when there is no cooling?

mdd1963 · Jul 13, 2017

As long as the cooling block is attached, some cooling will occur, but, if not pumping, it will heat up in a minute or two, I'd guess...

YOu can try plugging the pump into an aux fan header?

Danny_112 · Jul 13, 2017

Verify in your bios, you must have a fan control, that's set to low, or in
auto mode, etc...
If you do, then set these at full speed.
Reinstall your corsair Software, make sure it's running, and configured
correctly, put everything at 100%.

Go from there....

Dfrer :

Dfrer · Jul 13, 2017

Danny_112 :

I will give that a try, I have already tried maxing it out in the BIOS, on both the actual CPU_FAN header and a CHA_FAN header, both had no results, the other headers also did not work when quickly tested.

The problem that I am having with the Corsair software is that I actually run out of time when waiting for windows to load, as I've just installed the motherboard, Windows is having some trouble and every time that I run Windows it has to try to start the system repair, this as you know takes multiple minutes, and the CPU has already reached and almost gone over TJ max by the time I've even started the repair.

Dfrer · Jul 14, 2017

mdd1963 :

Is an AUX header straight from the powersupply? If so I have not.

Danny_112 · Jul 15, 2017

Test to make sure, your cooler is actually working....plug directly to psu, get an adaptor if need be....

nitinvaid20 · Jul 15, 2017

Same thing happened to me i guess this cooler are just install it and forget it if you remove it after some time clean it and install it it will not work...
i have cleaned my PC last week i had H100iV2 and my cooler stopped working when i am done with installing all parts now i dont have coolre but i am not gonna buy any more AIO coolers ill go for air coolers

Danny_112 · Jul 20, 2017

Dfrer :

Danny_112 :

I will give that a try, I have already tried maxing it out in the BIOS, on both the actual CPU_FAN header and a CHA_FAN header, both had no results, the other headers also did not work when quickly tested.

The problem that I am having with the Corsair software is that I actually run out of time when waiting for windows to load, as I've just installed the motherboard, Windows is having some trouble and every time that I run Windows it has to try to start the system repair, this as you know takes multiple minutes, and the CPU has already reached and almost gone over TJ max by the time I've even started the repair.

If your install of Windows is damaged, or functioning bad, reinstall from scratch.

I know it suck's having to do it, but, if your Windows is already buggy,
it will only get worst with time.
While you reinstall Windows, I suggest you use an air cooler, then once
everything is good, reinstall the Corsair....

Search

H100i GTX stops working after pc upgrade.

Dfrer

Honorable

nitinvaid20

mdd1963

Titan

Danny_112

Prominent

Dfrer

Honorable

Dfrer

Honorable

Danny_112

Prominent

nitinvaid20

Splendid

Danny_112

Prominent

TRENDING THREADS

Latest posts

Moderators online

Share this page