ASUS always booted fine before - haven’t changed anything

G

Guest

Guest
Archived from groups: alt.comp.periphs.mainboard.asus (More info?)

Thanks for any help on the following:

My XP system has worked great for months. Suddenly, after booting one
evening, XP doesn’t launch and the HDD LED indicator stays lit.

When the PC is started, both SATA hard drives are correctly identified
on screen as 250MB Maxtors, and both DVD drives are correctly
identified on screen as Primary Master IDE and Secondary Master IDE.
Memory is identified as 2048MB. There are no beeps on boot.

After boot, it is time for XP to start, but my case’s red HDD LED
lights up and stays lit. Instead of XP even trying to start, I get a
blank screen. A few times, I tried tapping ’F8’ on startup and
selected boot into ’Safe Mode’, but the blank screen appeared and the
red HDD LED lit immediately after making this choice. So, it seems
this has GOT to be a hardware problem.

Need I try a new Power Supply? If so, what kind?

The PC’s config:
XP Professional w/ Service Pack 2
CPU: (939-pin) AMD ATHLON64 4000+ CPU w/ Hyper Trans Tech
MOBOARD: ASUS A8V-E Deluxe VIA K8T890
Power Supply: ULTRA X-Connect 500W ATX PS
RAM: 2x1GB Corsair XMS High Performance Memory Modules
2 MAXTOR 250GB 7200 RPM Serial ATA 150 8MB CACHE HARD DRIVES
Video: Geforce 6800 ULTRA 512MB 16X PCI EXPRESS
1 AOPEN COMBO DRIVE (16X DVD-ROM & 52x32x52 CD-RW)
1 PIONEER DVR-109 DUAL FORMAT 16X DVD±R/±RW
1 Creative Labs SB Audigy-2 ZS 7.1
1.44 MB FLOPPY DRIVE
INTERNAL 6in1 Flash Media Reader/Writer
3COM US ROBOTIC PCI V.92 WINMODEM
3 CASE FANS

--
Posted using the http://www.hardwareforumz.com interface, at author's request
Articles individually checked for conformance to usenet standards
Topic URL: http://www.hardwareforumz.com/ASUS-booted-fine-haven-changed-ftopict62079.html
Visit Topic URL to contact author (reg. req'd). Report abuse: http://www.hardwareforumz.com/eform.php?p=312847
 

Paul

Splendid
Mar 30, 2004
5,267
0
25,780
Archived from groups: alt.comp.periphs.mainboard.asus (More info?)

In article <7_312847_d967ef2b3537daed75378303ced85a62@hardwareforumz.com>,
buzzer22 <UseLinkToEmail@HardwareForumz.com> wrote:

> Thanks for any help on the following:
>
> My XP system has worked great for months. Suddenly, after booting one
> evening, XP doesn’t launch and the HDD LED indicator stays lit.
>
> When the PC is started, both SATA hard drives are correctly identified
> on screen as 250MB Maxtors, and both DVD drives are correctly
> identified on screen as Primary Master IDE and Secondary Master IDE.
> Memory is identified as 2048MB. There are no beeps on boot.
>
> After boot, it is time for XP to start, but my case’s red HDD LED
> lights up and stays lit. Instead of XP even trying to start, I get a
> blank screen. A few times, I tried tapping ’F8’ on startup and
> selected boot into ’Safe Mode’, but the blank screen appeared and the
> red HDD LED lit immediately after making this choice. So, it seems
> this has GOT to be a hardware problem.
>
> Need I try a new Power Supply? If so, what kind?
>
> The PC’s config:
> XP Professional w/ Service Pack 2
> CPU: (939-pin) AMD ATHLON64 4000+ CPU w/ Hyper Trans Tech
> MOBOARD: ASUS A8V-E Deluxe VIA K8T890
> Power Supply: ULTRA X-Connect 500W ATX PS
> RAM: 2x1GB Corsair XMS High Performance Memory Modules
> 2 MAXTOR 250GB 7200 RPM Serial ATA 150 8MB CACHE HARD DRIVES
> Video: Geforce 6800 ULTRA 512MB 16X PCI EXPRESS
> 1 AOPEN COMBO DRIVE (16X DVD-ROM & 52x32x52 CD-RW)
> 1 PIONEER DVR-109 DUAL FORMAT 16X DVD±R/±RW
> 1 Creative Labs SB Audigy-2 ZS 7.1
> 1.44 MB FLOPPY DRIVE
> INTERNAL 6in1 Flash Media Reader/Writer
> 3COM US ROBOTIC PCI V.92 WINMODEM
> 3 CASE FANS

For future reference, there is a thread about power supply selection
here. The support forum for Ultra X-Connect supplies had enough
horror stories in it, that I would not buy that product. In any
case, I don't see a reason to condemn your power supply yet.

http://www.xtremesystems.org/forums/showthread.php?t=56231

If you wish to get some idea of the state of your power supply,
you can look at the hardware monitor in the BIOS. The +3.3, +5V,
and +12V should be within 5% of rated value. If, for example, the
+12V reads out at +11.4V or lower, it would be failing to meet the
5% requirement. There has to be some room allocated for measurement
error by the onboard hardware monitor, so if the rail dipped to maybe
+11.2, I'd be concerned. The reason I selected +12V, is the processor
draws its power from that rail. (A multimeter can be used to
verify what is seen in the hardware monitor.)

This sounds like it could be a disk failure of some sort. In which
case, I would not trust the opinions of a guy in a motherboard
group on how to fix a busted disk :) Find a Windows support group
or a disk storage USENET group.

From a hardware perspective, I would try simplifying the system.
Try to boot your Windows install CD, without the disks connected.
Try with only one storage device connected to the system at a time,
to see if this is an interface failure.

I would probably reach for my Knoppix boot CD. Knoppix runs from
a CD, and uses a RAM disk to hold volatile content. Knoppix can
be completely loaded into RAM, and the boot CD ejected, if need
be. Knoppix has the ability to recognize some kinds of foreign
file systems, and if your hard drives were connected, might
mount them on the desktop. It should not be writing to the
drives, unless you actually try to copy or move a file onto there.
By booting Knoppix, I would be attempting to prove the hardware
is basically good. I like to observe the boot messages, to see
if Knoppix is having trouble with any of the hardware.

In terms of bringing yourself up to speed on disk related issues,
I started by searching for "fixmbr" in Google. When suspecting
a disk failure, your primary concern is backups - do you have
a current backup ? I would not recommend attempting to use any
tool on a disk, unless I had a sector by sector image of the
disk. I learned this once, on a file system with duplicate directory
structures, where a recovery tool erased the good structure,
leaving both structures damaged. The main thing to remember
- don't do anything in a hurry - consider your options carefully.
Only use or apply a recovery tool, if you have a backup in hand.

If you don't have a spare drive handy, purchase enough spare
drives to hold the entire contents of any single computer you
own. That makes it easier to move stuff off the damaged disk
in the event of problems like this.

1) Try simplifying the current system. See if you can boot with
just the boot drive connected. Try moving the boot drive to a
different interface connector. Try a different cable. Check
that the cables are secure (especially with SATA connectors).

2) Try moving the boot disk to another, known working, computer.
See if the disk can be seen there. Your first objective will
be to get a backup image of the disk. Once you have a backup
of some sort, only then consider various recovery procedures.
That means, if you move the damaged boot drive to another
computer, you also want your spare disk(s) connected to that
computer as well, and have your backup software installed
on the spare computer, before connecting the damaged disk.
Pretend you are only going to get one shot at recovering the
data, if this is a disk head related problem (I learned that
lesson the hard way as well.)

3) Each disk drive company has diagnostic tools on their website.
Some of these tools do not work with all chipsets, meaning they
may not be able to see your disks anyway. The best time to test
such tools, is when you first get your new disk drive.

Those are some ideas, but everyone has their own favorite
recipe for what to do in an emergency. Consult a storage
group, if this is in fact a disk failure. I've had a couple
of disk failures, where I only got to power cycle the
drives a couple of times, before there was a complete
failure. If you are hearing any sounds that suggest a
head failure is imminent (clicking of drive trying to find
track 0 etc), you might only have one or two power cycles
before the thing quits completely.

HTH,
Paul
 

Chad

Distinguished
Apr 7, 2004
163
0
18,680
Archived from groups: alt.comp.periphs.mainboard.asus (More info?)

Well, this is a great time to buy a second drive, do a quick install of
WinXP on the new drive then plug in the old one and try to copy the
files over. (It may only have a problem booting and the files may be
fine). If not, use data recovery software to mine out your lost files.
Here are some freeware options:

http://free-backup.info/data-recovery-software.htm

Even if the problem is minor, every PC should have two drives at least
for use in critical data backup.

Good luck!
Chad