Sign in with
Sign up | Sign in
Your question

No ROM PCI IRQ routing table found: what does it mean ?

Last response: in Systems
Share
Anonymous
a b B Homebuilt system
December 2, 2004 7:59:02 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
the following message:

"ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!"

Does anyone have an idea about it ?

Thanks for you help

Claude

PS: Please find the complete results of the tests (displayed in a DOS
window):

Craig Hart's PCI+AGP bus sniffer, version 0.49ß, freeware made in
1996-2004a.

PCI BIOS Version 2.10 found!
Number of PCI Busses : 1
PCI Characteristics : Config Mechanism 1

Searching for PCI Devices using the System BIOS

Vendor 8086h Intel Corporation
Device 7100h 82439TX 430TX System Controller
Command 0006h (Memory Access, BusMaster)
Status 2200h (Received Master Abort, Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to HOST

Vendor 8086h Intel Corporation
Device 7110h 82371AB PIIX4 ISA Bridge
Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 80h, Bus Latency 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to ISA

Vendor 8086h Intel Corporation
Device 7111h 82371AB/EB/MB PIIX4/E/M EIDE Controller
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Storage, type IDE
PCI EIDE Controller Features :
BusMaster EIDE is supported
Primary Channel is at I/O Port 01F0h and IRQ 14
Secondary Channel is at I/O Port 0170h and IRQ 15
Address 4 is an I/O Port : 0000FFA0h

Vendor 8086h Intel Corporation
Device 7112h 82371AB/EB/MB PIIX4/E/M USB Controller
Command 0005h (I/O Access, BusMaster)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 40h
Self test 00h (Self test not supported)
PCI Class Serial, type USB (UHCI)
Address 4 is an I/O Port : 0000DB00h
System IRQ 3, INT# D

Vendor 8086h Intel Corporation
Device 7113h 82371AB PIIX4 Power Management Controller
Command 0003h (I/O Access, Memory Access)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 01h, Header Type 00h, Bus Latency 00h
Self test 00h (Self test not supported)
PCI Class Bridge, type PCI to Other

Vendor 1002h ATI Technologies
Device 4755h Rage 3D II+ [Mach64 GTB]
Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
Status 0280h (Supports Back-To-Back Trans., Medium Timing)
Revision 9Ah, Header Type 00h, Bus Latency 40h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Display, type VGA
Subsystem ID 47551002h Rage 3D II+ [Mach64 GTB] (Generic ID)
Subsystem Vendor 1002h ATI Technologies
Address 0 is a Memory Address (anywhere in 0-4Gb) : FE000000h
Address 1 is an I/O Port : 0000DE00h
Address 2 is a Memory Address (anywhere in 0-4Gb) : FFEFF000h
Expansion ROM of 0Kb decoded by this card

Vendor 10ECh Realtek Semiconductor
Device 8139h RT8139 (A/B/C/813x) Fast Ethernet Adapter
Command 0105h (I/O Access, BusMaster, System Errors)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans.,
Medium Timing)
Revision 10h, Header Type 00h, Bus Latency 80h
Self test 00h (Self test not supported)
PCI Class Network, type Ethernet
Subsystem ID 50001799h F5D5000 10/100 Fast Ethernet Adapter
Subsystem Vendor 1799h Belkin Research and Development Labs
Address 0 is an I/O Port : 0000DC00h
Address 1 is a Memory Address (anywhere in 0-4Gb) : FFEFEF00h
System IRQ 11, INT# A
Expansion ROM of 0Kb decoded by this card
New Capabilities List Present:
Power Management Capability, Version 1.1
Supports low power State D1
Supports low power State D2
Supports PME# from mode(s) D1, D2, D3hot
Current Power State : D0 (Device operational, no power saving)

ROM PCI IRQ routing table Windows 9x Compatibility Tests....
No ROM PCI IRQ routing table found!!!

IRQ Summary: IRQs 3,11,14,15 are used by PCI devices
Shared IRQs: There are no shared PCI IRQs
December 2, 2004 7:59:03 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

change PnP Os installed? to the opposite of what you have now in the
bios...yes/no


"claude" <nospam@nospam.fr> wrote in message
news:41AF3BC6.8010701@nospam.fr...
> I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
> the following message:
>
> "ROM PCI IRQ routing table Windows 9x Compatibility Tests....
> No ROM PCI IRQ routing table found!!!"
>
> Does anyone have an idea about it ?
>
> Thanks for you help
>
> Claude
>
> PS: Please find the complete results of the tests (displayed in a DOS
> window):
>
> Craig Hart's PCI+AGP bus sniffer, version 0.49ß, freeware made in
> 1996-2004a.
>
> PCI BIOS Version 2.10 found!
> Number of PCI Busses : 1
> PCI Characteristics : Config Mechanism 1
>
> Searching for PCI Devices using the System BIOS
>
> Vendor 8086h Intel Corporation
> Device 7100h 82439TX 430TX System Controller
> Command 0006h (Memory Access, BusMaster)
> Status 2200h (Received Master Abort, Medium Timing)
> Revision 01h, Header Type 00h, Bus Latency 20h
> Self test 00h (Self test not supported)
> PCI Class Bridge, type PCI to HOST
>
> Vendor 8086h Intel Corporation
> Device 7110h 82371AB PIIX4 ISA Bridge
> Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
> Revision 01h, Header Type 80h, Bus Latency 00h
> Self test 00h (Self test not supported)
> PCI Class Bridge, type PCI to ISA
>
> Vendor 8086h Intel Corporation
> Device 7111h 82371AB/EB/MB PIIX4/E/M EIDE Controller
> Command 0005h (I/O Access, BusMaster)
> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
> Revision 01h, Header Type 00h, Bus Latency 20h
> Self test 00h (Self test not supported)
> PCI Class Storage, type IDE
> PCI EIDE Controller Features :
> BusMaster EIDE is supported
> Primary Channel is at I/O Port 01F0h and IRQ 14
> Secondary Channel is at I/O Port 0170h and IRQ 15
> Address 4 is an I/O Port : 0000FFA0h
>
> Vendor 8086h Intel Corporation
> Device 7112h 82371AB/EB/MB PIIX4/E/M USB Controller
> Command 0005h (I/O Access, BusMaster)
> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
> Revision 01h, Header Type 00h, Bus Latency 40h
> Self test 00h (Self test not supported)
> PCI Class Serial, type USB (UHCI)
> Address 4 is an I/O Port : 0000DB00h
> System IRQ 3, INT# D
>
> Vendor 8086h Intel Corporation
> Device 7113h 82371AB PIIX4 Power Management Controller
> Command 0003h (I/O Access, Memory Access)
> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
> Revision 01h, Header Type 00h, Bus Latency 00h
> Self test 00h (Self test not supported)
> PCI Class Bridge, type PCI to Other
>
> Vendor 1002h ATI Technologies
> Device 4755h Rage 3D II+ [Mach64 GTB]
> Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
> Revision 9Ah, Header Type 00h, Bus Latency 40h
> Self test 00h (Self test not supported)
> Cache line size 32 Bytes (8 DWords)
> PCI Class Display, type VGA
> Subsystem ID 47551002h Rage 3D II+ [Mach64 GTB] (Generic ID)
> Subsystem Vendor 1002h ATI Technologies
> Address 0 is a Memory Address (anywhere in 0-4Gb) : FE000000h
> Address 1 is an I/O Port : 0000DE00h
> Address 2 is a Memory Address (anywhere in 0-4Gb) : FFEFF000h
> Expansion ROM of 0Kb decoded by this card
>
> Vendor 10ECh Realtek Semiconductor
> Device 8139h RT8139 (A/B/C/813x) Fast Ethernet Adapter
> Command 0105h (I/O Access, BusMaster, System Errors)
> Status 0290h (Has Capabilities List, Supports Back-To-Back Trans.,
> Medium Timing)
> Revision 10h, Header Type 00h, Bus Latency 80h
> Self test 00h (Self test not supported)
> PCI Class Network, type Ethernet
> Subsystem ID 50001799h F5D5000 10/100 Fast Ethernet Adapter
> Subsystem Vendor 1799h Belkin Research and Development Labs
> Address 0 is an I/O Port : 0000DC00h
> Address 1 is a Memory Address (anywhere in 0-4Gb) : FFEFEF00h
> System IRQ 11, INT# A
> Expansion ROM of 0Kb decoded by this card
> New Capabilities List Present:
> Power Management Capability, Version 1.1
> Supports low power State D1
> Supports low power State D2
> Supports PME# from mode(s) D1, D2, D3hot
> Current Power State : D0 (Device operational, no power saving)
>
> ROM PCI IRQ routing table Windows 9x Compatibility Tests....
> No ROM PCI IRQ routing table found!!!
>
> IRQ Summary: IRQs 3,11,14,15 are used by PCI devices
> Shared IRQs: There are no shared PCI IRQs
>
>
>
December 2, 2004 7:59:03 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

also is that a VIA based mainboard? miniport driver for irq steering may
not be loaded. ACPI
set to?


"claude" <nospam@nospam.fr> wrote in message
news:41AF3BC6.8010701@nospam.fr...
> I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
> the following message:
>
> "ROM PCI IRQ routing table Windows 9x Compatibility Tests....
> No ROM PCI IRQ routing table found!!!"
>
> Does anyone have an idea about it ?
>
> Thanks for you help
>
> Claude
>
> PS: Please find the complete results of the tests (displayed in a DOS
> window):
>
> Craig Hart's PCI+AGP bus sniffer, version 0.49ß, freeware made in
> 1996-2004a.
>
> PCI BIOS Version 2.10 found!
> Number of PCI Busses : 1
> PCI Characteristics : Config Mechanism 1
>
> Searching for PCI Devices using the System BIOS
>
> Vendor 8086h Intel Corporation
> Device 7100h 82439TX 430TX System Controller
> Command 0006h (Memory Access, BusMaster)
> Status 2200h (Received Master Abort, Medium Timing)
> Revision 01h, Header Type 00h, Bus Latency 20h
> Self test 00h (Self test not supported)
> PCI Class Bridge, type PCI to HOST
>
> Vendor 8086h Intel Corporation
> Device 7110h 82371AB PIIX4 ISA Bridge
> Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
> Revision 01h, Header Type 80h, Bus Latency 00h
> Self test 00h (Self test not supported)
> PCI Class Bridge, type PCI to ISA
>
> Vendor 8086h Intel Corporation
> Device 7111h 82371AB/EB/MB PIIX4/E/M EIDE Controller
> Command 0005h (I/O Access, BusMaster)
> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
> Revision 01h, Header Type 00h, Bus Latency 20h
> Self test 00h (Self test not supported)
> PCI Class Storage, type IDE
> PCI EIDE Controller Features :
> BusMaster EIDE is supported
> Primary Channel is at I/O Port 01F0h and IRQ 14
> Secondary Channel is at I/O Port 0170h and IRQ 15
> Address 4 is an I/O Port : 0000FFA0h
>
> Vendor 8086h Intel Corporation
> Device 7112h 82371AB/EB/MB PIIX4/E/M USB Controller
> Command 0005h (I/O Access, BusMaster)
> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
> Revision 01h, Header Type 00h, Bus Latency 40h
> Self test 00h (Self test not supported)
> PCI Class Serial, type USB (UHCI)
> Address 4 is an I/O Port : 0000DB00h
> System IRQ 3, INT# D
>
> Vendor 8086h Intel Corporation
> Device 7113h 82371AB PIIX4 Power Management Controller
> Command 0003h (I/O Access, Memory Access)
> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
> Revision 01h, Header Type 00h, Bus Latency 00h
> Self test 00h (Self test not supported)
> PCI Class Bridge, type PCI to Other
>
> Vendor 1002h ATI Technologies
> Device 4755h Rage 3D II+ [Mach64 GTB]
> Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
> Revision 9Ah, Header Type 00h, Bus Latency 40h
> Self test 00h (Self test not supported)
> Cache line size 32 Bytes (8 DWords)
> PCI Class Display, type VGA
> Subsystem ID 47551002h Rage 3D II+ [Mach64 GTB] (Generic ID)
> Subsystem Vendor 1002h ATI Technologies
> Address 0 is a Memory Address (anywhere in 0-4Gb) : FE000000h
> Address 1 is an I/O Port : 0000DE00h
> Address 2 is a Memory Address (anywhere in 0-4Gb) : FFEFF000h
> Expansion ROM of 0Kb decoded by this card
>
> Vendor 10ECh Realtek Semiconductor
> Device 8139h RT8139 (A/B/C/813x) Fast Ethernet Adapter
> Command 0105h (I/O Access, BusMaster, System Errors)
> Status 0290h (Has Capabilities List, Supports Back-To-Back Trans.,
> Medium Timing)
> Revision 10h, Header Type 00h, Bus Latency 80h
> Self test 00h (Self test not supported)
> PCI Class Network, type Ethernet
> Subsystem ID 50001799h F5D5000 10/100 Fast Ethernet Adapter
> Subsystem Vendor 1799h Belkin Research and Development Labs
> Address 0 is an I/O Port : 0000DC00h
> Address 1 is a Memory Address (anywhere in 0-4Gb) : FFEFEF00h
> System IRQ 11, INT# A
> Expansion ROM of 0Kb decoded by this card
> New Capabilities List Present:
> Power Management Capability, Version 1.1
> Supports low power State D1
> Supports low power State D2
> Supports PME# from mode(s) D1, D2, D3hot
> Current Power State : D0 (Device operational, no power saving)
>
> ROM PCI IRQ routing table Windows 9x Compatibility Tests....
> No ROM PCI IRQ routing table found!!!
>
> IRQ Summary: IRQs 3,11,14,15 are used by PCI devices
> Shared IRQs: There are no shared PCI IRQs
>
>
>
Related resources
Anonymous
a b B Homebuilt system
December 2, 2004 8:28:34 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

JAD a écrit:
> also is that a VIA based mainboard?

What do you mean with VIA ?

> miniport driver for irq steering may
> not be loaded.

I forgot to say that my OS is W98SE.
In the PCI bus properties, I have everything crossed (in "use the IRQ
steering) except "Getting the IRQ table from PCIBIOS 2.1 in protected mode.

> ACPI set to?

I don't think I have this option in the bios settings (but I'll check it )

thanks

>
>
> "claude" <nospam@nospam.fr> wrote in message
> news:41AF3BC6.8010701@nospam.fr...
>
>>I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
>>the following message:
>>
>>"ROM PCI IRQ routing table Windows 9x Compatibility Tests....
>>No ROM PCI IRQ routing table found!!!"
>>
>>Does anyone have an idea about it ?
>>
>>Thanks for you help
>>
>>Claude
>>
>>PS: Please find the complete results of the tests (displayed in a DOS
>>window):
>>
>>Craig Hart's PCI+AGP bus sniffer, version 0.49ß, freeware made in
>>1996-2004a.
>>
>>PCI BIOS Version 2.10 found!
>>Number of PCI Busses : 1
>>PCI Characteristics : Config Mechanism 1
>>
>>Searching for PCI Devices using the System BIOS
>>
>> Vendor 8086h Intel Corporation
>> Device 7100h 82439TX 430TX System Controller
>> Command 0006h (Memory Access, BusMaster)
>> Status 2200h (Received Master Abort, Medium Timing)
>> Revision 01h, Header Type 00h, Bus Latency 20h
>> Self test 00h (Self test not supported)
>> PCI Class Bridge, type PCI to HOST
>>
>> Vendor 8086h Intel Corporation
>> Device 7110h 82371AB PIIX4 ISA Bridge
>> Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>> Revision 01h, Header Type 80h, Bus Latency 00h
>> Self test 00h (Self test not supported)
>> PCI Class Bridge, type PCI to ISA
>>
>> Vendor 8086h Intel Corporation
>> Device 7111h 82371AB/EB/MB PIIX4/E/M EIDE Controller
>> Command 0005h (I/O Access, BusMaster)
>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>> Revision 01h, Header Type 00h, Bus Latency 20h
>> Self test 00h (Self test not supported)
>> PCI Class Storage, type IDE
>> PCI EIDE Controller Features :
>> BusMaster EIDE is supported
>> Primary Channel is at I/O Port 01F0h and IRQ 14
>> Secondary Channel is at I/O Port 0170h and IRQ 15
>> Address 4 is an I/O Port : 0000FFA0h
>>
>> Vendor 8086h Intel Corporation
>> Device 7112h 82371AB/EB/MB PIIX4/E/M USB Controller
>> Command 0005h (I/O Access, BusMaster)
>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>> Revision 01h, Header Type 00h, Bus Latency 40h
>> Self test 00h (Self test not supported)
>> PCI Class Serial, type USB (UHCI)
>> Address 4 is an I/O Port : 0000DB00h
>> System IRQ 3, INT# D
>>
>> Vendor 8086h Intel Corporation
>> Device 7113h 82371AB PIIX4 Power Management Controller
>> Command 0003h (I/O Access, Memory Access)
>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>> Revision 01h, Header Type 00h, Bus Latency 00h
>> Self test 00h (Self test not supported)
>> PCI Class Bridge, type PCI to Other
>>
>> Vendor 1002h ATI Technologies
>> Device 4755h Rage 3D II+ [Mach64 GTB]
>> Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>> Revision 9Ah, Header Type 00h, Bus Latency 40h
>> Self test 00h (Self test not supported)
>> Cache line size 32 Bytes (8 DWords)
>> PCI Class Display, type VGA
>> Subsystem ID 47551002h Rage 3D II+ [Mach64 GTB] (Generic ID)
>> Subsystem Vendor 1002h ATI Technologies
>> Address 0 is a Memory Address (anywhere in 0-4Gb) : FE000000h
>> Address 1 is an I/O Port : 0000DE00h
>> Address 2 is a Memory Address (anywhere in 0-4Gb) : FFEFF000h
>> Expansion ROM of 0Kb decoded by this card
>>
>> Vendor 10ECh Realtek Semiconductor
>> Device 8139h RT8139 (A/B/C/813x) Fast Ethernet Adapter
>> Command 0105h (I/O Access, BusMaster, System Errors)
>> Status 0290h (Has Capabilities List, Supports Back-To-Back Trans.,
>> Medium Timing)
>> Revision 10h, Header Type 00h, Bus Latency 80h
>> Self test 00h (Self test not supported)
>> PCI Class Network, type Ethernet
>> Subsystem ID 50001799h F5D5000 10/100 Fast Ethernet Adapter
>> Subsystem Vendor 1799h Belkin Research and Development Labs
>> Address 0 is an I/O Port : 0000DC00h
>> Address 1 is a Memory Address (anywhere in 0-4Gb) : FFEFEF00h
>> System IRQ 11, INT# A
>> Expansion ROM of 0Kb decoded by this card
>> New Capabilities List Present:
>> Power Management Capability, Version 1.1
>> Supports low power State D1
>> Supports low power State D2
>> Supports PME# from mode(s) D1, D2, D3hot
>> Current Power State : D0 (Device operational, no power saving)
>>
>>ROM PCI IRQ routing table Windows 9x Compatibility Tests....
>>No ROM PCI IRQ routing table found!!!
>>
>>IRQ Summary: IRQs 3,11,14,15 are used by PCI devices
>>Shared IRQs: There are no shared PCI IRQs
>>
>>
>>
>
>
>
Anonymous
a b B Homebuilt system
December 2, 2004 8:30:12 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

JAD a écrit:
> change PnP Os installed? to the opposite of what you have now in the
> bios...yes/no

I tried both. but, I 'll check it again

thanks

>
>
> "claude" <nospam@nospam.fr> wrote in message
> news:41AF3BC6.8010701@nospam.fr...
>
>>I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
>>the following message:
>>
>>"ROM PCI IRQ routing table Windows 9x Compatibility Tests....
>>No ROM PCI IRQ routing table found!!!"
>>
>>Does anyone have an idea about it ?
>>
>>Thanks for you help
>>
>>Claude
>>
>>PS: Please find the complete results of the tests (displayed in a DOS
>>window):
>>
>>Craig Hart's PCI+AGP bus sniffer, version 0.49ß, freeware made in
>>1996-2004a.
>>
>>PCI BIOS Version 2.10 found!
>>Number of PCI Busses : 1
>>PCI Characteristics : Config Mechanism 1
>>
>>Searching for PCI Devices using the System BIOS
>>
>> Vendor 8086h Intel Corporation
>> Device 7100h 82439TX 430TX System Controller
>> Command 0006h (Memory Access, BusMaster)
>> Status 2200h (Received Master Abort, Medium Timing)
>> Revision 01h, Header Type 00h, Bus Latency 20h
>> Self test 00h (Self test not supported)
>> PCI Class Bridge, type PCI to HOST
>>
>> Vendor 8086h Intel Corporation
>> Device 7110h 82371AB PIIX4 ISA Bridge
>> Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>> Revision 01h, Header Type 80h, Bus Latency 00h
>> Self test 00h (Self test not supported)
>> PCI Class Bridge, type PCI to ISA
>>
>> Vendor 8086h Intel Corporation
>> Device 7111h 82371AB/EB/MB PIIX4/E/M EIDE Controller
>> Command 0005h (I/O Access, BusMaster)
>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>> Revision 01h, Header Type 00h, Bus Latency 20h
>> Self test 00h (Self test not supported)
>> PCI Class Storage, type IDE
>> PCI EIDE Controller Features :
>> BusMaster EIDE is supported
>> Primary Channel is at I/O Port 01F0h and IRQ 14
>> Secondary Channel is at I/O Port 0170h and IRQ 15
>> Address 4 is an I/O Port : 0000FFA0h
>>
>> Vendor 8086h Intel Corporation
>> Device 7112h 82371AB/EB/MB PIIX4/E/M USB Controller
>> Command 0005h (I/O Access, BusMaster)
>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>> Revision 01h, Header Type 00h, Bus Latency 40h
>> Self test 00h (Self test not supported)
>> PCI Class Serial, type USB (UHCI)
>> Address 4 is an I/O Port : 0000DB00h
>> System IRQ 3, INT# D
>>
>> Vendor 8086h Intel Corporation
>> Device 7113h 82371AB PIIX4 Power Management Controller
>> Command 0003h (I/O Access, Memory Access)
>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>> Revision 01h, Header Type 00h, Bus Latency 00h
>> Self test 00h (Self test not supported)
>> PCI Class Bridge, type PCI to Other
>>
>> Vendor 1002h ATI Technologies
>> Device 4755h Rage 3D II+ [Mach64 GTB]
>> Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>> Revision 9Ah, Header Type 00h, Bus Latency 40h
>> Self test 00h (Self test not supported)
>> Cache line size 32 Bytes (8 DWords)
>> PCI Class Display, type VGA
>> Subsystem ID 47551002h Rage 3D II+ [Mach64 GTB] (Generic ID)
>> Subsystem Vendor 1002h ATI Technologies
>> Address 0 is a Memory Address (anywhere in 0-4Gb) : FE000000h
>> Address 1 is an I/O Port : 0000DE00h
>> Address 2 is a Memory Address (anywhere in 0-4Gb) : FFEFF000h
>> Expansion ROM of 0Kb decoded by this card
>>
>> Vendor 10ECh Realtek Semiconductor
>> Device 8139h RT8139 (A/B/C/813x) Fast Ethernet Adapter
>> Command 0105h (I/O Access, BusMaster, System Errors)
>> Status 0290h (Has Capabilities List, Supports Back-To-Back Trans.,
>> Medium Timing)
>> Revision 10h, Header Type 00h, Bus Latency 80h
>> Self test 00h (Self test not supported)
>> PCI Class Network, type Ethernet
>> Subsystem ID 50001799h F5D5000 10/100 Fast Ethernet Adapter
>> Subsystem Vendor 1799h Belkin Research and Development Labs
>> Address 0 is an I/O Port : 0000DC00h
>> Address 1 is a Memory Address (anywhere in 0-4Gb) : FFEFEF00h
>> System IRQ 11, INT# A
>> Expansion ROM of 0Kb decoded by this card
>> New Capabilities List Present:
>> Power Management Capability, Version 1.1
>> Supports low power State D1
>> Supports low power State D2
>> Supports PME# from mode(s) D1, D2, D3hot
>> Current Power State : D0 (Device operational, no power saving)
>>
>>ROM PCI IRQ routing table Windows 9x Compatibility Tests....
>>No ROM PCI IRQ routing table found!!!
>>
>>IRQ Summary: IRQs 3,11,14,15 are used by PCI devices
>>Shared IRQs: There are no shared PCI IRQs
>>
>>
>>
>
>
>
Anonymous
a b B Homebuilt system
December 2, 2004 8:38:16 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

Whatever the PnP OS settings (yes/no), I get the same result: No ROM PCI
IRQ routing table found.

I haven't found anything looking like an ACPI option in the bios settings.

claude a écrit:
>
>
> JAD a écrit:
>
>> change PnP Os installed? to the opposite of what you have now in the
>> bios...yes/no
>
>
> I tried both. but, I 'll check it again
>
> thanks
>
>>
>>
>> "claude" <nospam@nospam.fr> wrote in message
>> news:41AF3BC6.8010701@nospam.fr...
>>
>>> I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
>>> the following message:
>>>
>>> "ROM PCI IRQ routing table Windows 9x Compatibility Tests....
>>> No ROM PCI IRQ routing table found!!!"
>>>
>>> Does anyone have an idea about it ?
>>>
>>> Thanks for you help
>>>
>>> Claude
>>>
>>> PS: Please find the complete results of the tests (displayed in a DOS
>>> window):
>>>
>>> Craig Hart's PCI+AGP bus sniffer, version 0.49ß, freeware made in
>>> 1996-2004a.
>>>
>>> PCI BIOS Version 2.10 found!
>>> Number of PCI Busses : 1
>>> PCI Characteristics : Config Mechanism 1
>>>
>>> Searching for PCI Devices using the System BIOS
>>>
>>> Vendor 8086h Intel Corporation
>>> Device 7100h 82439TX 430TX System Controller
>>> Command 0006h (Memory Access, BusMaster)
>>> Status 2200h (Received Master Abort, Medium Timing)
>>> Revision 01h, Header Type 00h, Bus Latency 20h
>>> Self test 00h (Self test not supported)
>>> PCI Class Bridge, type PCI to HOST
>>>
>>> Vendor 8086h Intel Corporation
>>> Device 7110h 82371AB PIIX4 ISA Bridge
>>> Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
>>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>>> Revision 01h, Header Type 80h, Bus Latency 00h
>>> Self test 00h (Self test not supported)
>>> PCI Class Bridge, type PCI to ISA
>>>
>>> Vendor 8086h Intel Corporation
>>> Device 7111h 82371AB/EB/MB PIIX4/E/M EIDE Controller
>>> Command 0005h (I/O Access, BusMaster)
>>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>>> Revision 01h, Header Type 00h, Bus Latency 20h
>>> Self test 00h (Self test not supported)
>>> PCI Class Storage, type IDE
>>> PCI EIDE Controller Features :
>>> BusMaster EIDE is supported
>>> Primary Channel is at I/O Port 01F0h and IRQ 14
>>> Secondary Channel is at I/O Port 0170h and IRQ 15
>>> Address 4 is an I/O Port : 0000FFA0h
>>>
>>> Vendor 8086h Intel Corporation
>>> Device 7112h 82371AB/EB/MB PIIX4/E/M USB Controller
>>> Command 0005h (I/O Access, BusMaster)
>>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>>> Revision 01h, Header Type 00h, Bus Latency 40h
>>> Self test 00h (Self test not supported)
>>> PCI Class Serial, type USB (UHCI)
>>> Address 4 is an I/O Port : 0000DB00h
>>> System IRQ 3, INT# D
>>>
>>> Vendor 8086h Intel Corporation
>>> Device 7113h 82371AB PIIX4 Power Management Controller
>>> Command 0003h (I/O Access, Memory Access)
>>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>>> Revision 01h, Header Type 00h, Bus Latency 00h
>>> Self test 00h (Self test not supported)
>>> PCI Class Bridge, type PCI to Other
>>>
>>> Vendor 1002h ATI Technologies
>>> Device 4755h Rage 3D II+ [Mach64 GTB]
>>> Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
>>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>>> Revision 9Ah, Header Type 00h, Bus Latency 40h
>>> Self test 00h (Self test not supported)
>>> Cache line size 32 Bytes (8 DWords)
>>> PCI Class Display, type VGA
>>> Subsystem ID 47551002h Rage 3D II+ [Mach64 GTB] (Generic ID)
>>> Subsystem Vendor 1002h ATI Technologies
>>> Address 0 is a Memory Address (anywhere in 0-4Gb) : FE000000h
>>> Address 1 is an I/O Port : 0000DE00h
>>> Address 2 is a Memory Address (anywhere in 0-4Gb) : FFEFF000h
>>> Expansion ROM of 0Kb decoded by this card
>>>
>>> Vendor 10ECh Realtek Semiconductor
>>> Device 8139h RT8139 (A/B/C/813x) Fast Ethernet Adapter
>>> Command 0105h (I/O Access, BusMaster, System Errors)
>>> Status 0290h (Has Capabilities List, Supports Back-To-Back Trans.,
>>> Medium Timing)
>>> Revision 10h, Header Type 00h, Bus Latency 80h
>>> Self test 00h (Self test not supported)
>>> PCI Class Network, type Ethernet
>>> Subsystem ID 50001799h F5D5000 10/100 Fast Ethernet Adapter
>>> Subsystem Vendor 1799h Belkin Research and Development Labs
>>> Address 0 is an I/O Port : 0000DC00h
>>> Address 1 is a Memory Address (anywhere in 0-4Gb) : FFEFEF00h
>>> System IRQ 11, INT# A
>>> Expansion ROM of 0Kb decoded by this card
>>> New Capabilities List Present:
>>> Power Management Capability, Version 1.1
>>> Supports low power State D1
>>> Supports low power State D2
>>> Supports PME# from mode(s) D1, D2, D3hot
>>> Current Power State : D0 (Device operational, no power saving)
>>>
>>> ROM PCI IRQ routing table Windows 9x Compatibility Tests....
>>> No ROM PCI IRQ routing table found!!!
>>>
>>> IRQ Summary: IRQs 3,11,14,15 are used by PCI devices
>>> Shared IRQs: There are no shared PCI IRQs
>>>
>>>
>>>
>>
>>
>>
>
Anonymous
a b B Homebuilt system
December 2, 2004 9:03:12 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

I don't know if this can help you, but, I have a dual boot W98SE/linux.
and, in the linux logs, I have this curious message:
"Nov 26 16:24:27 kernel: PCI: Cannot allocate resource region 0 of
device 0000:00:08.0"

the device 8 is my vga card as described here:

Bus 0, device 8, function 0:
VGA compatible controller: ATI Technologies Inc 3D Rage II+ 215GTB
[Mach64 GTB] (rev 154).
Master Capable. Latency=64. Min Gnt=8.
Non-prefetchable 32 bit memory at 0x10000000 [0x10ffffff].
I/O at 0xde00 [0xdeff].
Non-prefetchable 32 bit memory at 0xffeff000 [0xffefffff].

It would seem that my processor is not able to access directly to the
video RAM... but, i'm not sure of this.
what do you think of this issue ?

thanks


JAD a écrit:
> also is that a VIA based mainboard? miniport driver for irq steering may
> not be loaded. ACPI
> set to?
>
>
> "claude" <nospam@nospam.fr> wrote in message
> news:41AF3BC6.8010701@nospam.fr...
>
>>I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
>>the following message:
>>
>>"ROM PCI IRQ routing table Windows 9x Compatibility Tests....
>>No ROM PCI IRQ routing table found!!!"
>>
>>Does anyone have an idea about it ?
>>
>>Thanks for you help
>>
>>Claude
>>
>>PS: Please find the complete results of the tests (displayed in a DOS
>>window):
>>
>>Craig Hart's PCI+AGP bus sniffer, version 0.49ß, freeware made in
>>1996-2004a.
>>
>>PCI BIOS Version 2.10 found!
>>Number of PCI Busses : 1
>>PCI Characteristics : Config Mechanism 1
>>
>>Searching for PCI Devices using the System BIOS
>>
>> Vendor 8086h Intel Corporation
>> Device 7100h 82439TX 430TX System Controller
>> Command 0006h (Memory Access, BusMaster)
>> Status 2200h (Received Master Abort, Medium Timing)
>> Revision 01h, Header Type 00h, Bus Latency 20h
>> Self test 00h (Self test not supported)
>> PCI Class Bridge, type PCI to HOST
>>
>> Vendor 8086h Intel Corporation
>> Device 7110h 82371AB PIIX4 ISA Bridge
>> Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>> Revision 01h, Header Type 80h, Bus Latency 00h
>> Self test 00h (Self test not supported)
>> PCI Class Bridge, type PCI to ISA
>>
>> Vendor 8086h Intel Corporation
>> Device 7111h 82371AB/EB/MB PIIX4/E/M EIDE Controller
>> Command 0005h (I/O Access, BusMaster)
>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>> Revision 01h, Header Type 00h, Bus Latency 20h
>> Self test 00h (Self test not supported)
>> PCI Class Storage, type IDE
>> PCI EIDE Controller Features :
>> BusMaster EIDE is supported
>> Primary Channel is at I/O Port 01F0h and IRQ 14
>> Secondary Channel is at I/O Port 0170h and IRQ 15
>> Address 4 is an I/O Port : 0000FFA0h
>>
>> Vendor 8086h Intel Corporation
>> Device 7112h 82371AB/EB/MB PIIX4/E/M USB Controller
>> Command 0005h (I/O Access, BusMaster)
>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>> Revision 01h, Header Type 00h, Bus Latency 40h
>> Self test 00h (Self test not supported)
>> PCI Class Serial, type USB (UHCI)
>> Address 4 is an I/O Port : 0000DB00h
>> System IRQ 3, INT# D
>>
>> Vendor 8086h Intel Corporation
>> Device 7113h 82371AB PIIX4 Power Management Controller
>> Command 0003h (I/O Access, Memory Access)
>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>> Revision 01h, Header Type 00h, Bus Latency 00h
>> Self test 00h (Self test not supported)
>> PCI Class Bridge, type PCI to Other
>>
>> Vendor 1002h ATI Technologies
>> Device 4755h Rage 3D II+ [Mach64 GTB]
>> Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
>> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
>> Revision 9Ah, Header Type 00h, Bus Latency 40h
>> Self test 00h (Self test not supported)
>> Cache line size 32 Bytes (8 DWords)
>> PCI Class Display, type VGA
>> Subsystem ID 47551002h Rage 3D II+ [Mach64 GTB] (Generic ID)
>> Subsystem Vendor 1002h ATI Technologies
>> Address 0 is a Memory Address (anywhere in 0-4Gb) : FE000000h
>> Address 1 is an I/O Port : 0000DE00h
>> Address 2 is a Memory Address (anywhere in 0-4Gb) : FFEFF000h
>> Expansion ROM of 0Kb decoded by this card
>>
>> Vendor 10ECh Realtek Semiconductor
>> Device 8139h RT8139 (A/B/C/813x) Fast Ethernet Adapter
>> Command 0105h (I/O Access, BusMaster, System Errors)
>> Status 0290h (Has Capabilities List, Supports Back-To-Back Trans.,
>> Medium Timing)
>> Revision 10h, Header Type 00h, Bus Latency 80h
>> Self test 00h (Self test not supported)
>> PCI Class Network, type Ethernet
>> Subsystem ID 50001799h F5D5000 10/100 Fast Ethernet Adapter
>> Subsystem Vendor 1799h Belkin Research and Development Labs
>> Address 0 is an I/O Port : 0000DC00h
>> Address 1 is a Memory Address (anywhere in 0-4Gb) : FFEFEF00h
>> System IRQ 11, INT# A
>> Expansion ROM of 0Kb decoded by this card
>> New Capabilities List Present:
>> Power Management Capability, Version 1.1
>> Supports low power State D1
>> Supports low power State D2
>> Supports PME# from mode(s) D1, D2, D3hot
>> Current Power State : D0 (Device operational, no power saving)
>>
>>ROM PCI IRQ routing table Windows 9x Compatibility Tests....
>>No ROM PCI IRQ routing table found!!!
>>
>>IRQ Summary: IRQs 3,11,14,15 are used by PCI devices
>>Shared IRQs: There are no shared PCI IRQs
>>
>>
>>
>
>
>
Anonymous
a b B Homebuilt system
December 2, 2004 11:54:33 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

claude wrote:

> I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
> the following message:
>
> "ROM PCI IRQ routing table Windows 9x Compatibility Tests....
> No ROM PCI IRQ routing table found!!!"
>
> Does anyone have an idea about it ?

Your BIOS apparently doesn't have a PCI IRQ Routing Table so Windows will
not be able to dynamically route PCI IRQ assignments.

http://www.microsoft.com/whdc/archive/pciirq.mspx


> Thanks for you help
>
> Claude
>
> PS: Please find the complete results of the tests (displayed in a DOS
> window):
>
> Craig Hart's PCI+AGP bus sniffer, version 0.49ß, freeware made in
> 1996-2004a.
>
> PCI BIOS Version 2.10 found!
> Number of PCI Busses : 1
> PCI Characteristics : Config Mechanism 1
>
> Searching for PCI Devices using the System BIOS
>
> Vendor 8086h Intel Corporation
> Device 7100h 82439TX 430TX System Controller
> Command 0006h (Memory Access, BusMaster)
> Status 2200h (Received Master Abort, Medium Timing)
> Revision 01h, Header Type 00h, Bus Latency 20h
> Self test 00h (Self test not supported)
> PCI Class Bridge, type PCI to HOST
>
> Vendor 8086h Intel Corporation
> Device 7110h 82371AB PIIX4 ISA Bridge
> Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles)
> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
> Revision 01h, Header Type 80h, Bus Latency 00h
> Self test 00h (Self test not supported)
> PCI Class Bridge, type PCI to ISA
>
> Vendor 8086h Intel Corporation
> Device 7111h 82371AB/EB/MB PIIX4/E/M EIDE Controller
> Command 0005h (I/O Access, BusMaster)
> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
> Revision 01h, Header Type 00h, Bus Latency 20h
> Self test 00h (Self test not supported)
> PCI Class Storage, type IDE
> PCI EIDE Controller Features :
> BusMaster EIDE is supported
> Primary Channel is at I/O Port 01F0h and IRQ 14
> Secondary Channel is at I/O Port 0170h and IRQ 15
> Address 4 is an I/O Port : 0000FFA0h
>
> Vendor 8086h Intel Corporation
> Device 7112h 82371AB/EB/MB PIIX4/E/M USB Controller
> Command 0005h (I/O Access, BusMaster)
> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
> Revision 01h, Header Type 00h, Bus Latency 40h
> Self test 00h (Self test not supported)
> PCI Class Serial, type USB (UHCI)
> Address 4 is an I/O Port : 0000DB00h
> System IRQ 3, INT# D
>
> Vendor 8086h Intel Corporation
> Device 7113h 82371AB PIIX4 Power Management Controller
> Command 0003h (I/O Access, Memory Access)
> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
> Revision 01h, Header Type 00h, Bus Latency 00h
> Self test 00h (Self test not supported)
> PCI Class Bridge, type PCI to Other
>
> Vendor 1002h ATI Technologies
> Device 4755h Rage 3D II+ [Mach64 GTB]
> Command 0087h (I/O Access, Memory Access, BusMaster, Wait Cycles)
> Status 0280h (Supports Back-To-Back Trans., Medium Timing)
> Revision 9Ah, Header Type 00h, Bus Latency 40h
> Self test 00h (Self test not supported)
> Cache line size 32 Bytes (8 DWords)
> PCI Class Display, type VGA
> Subsystem ID 47551002h Rage 3D II+ [Mach64 GTB] (Generic ID)
> Subsystem Vendor 1002h ATI Technologies
> Address 0 is a Memory Address (anywhere in 0-4Gb) : FE000000h
> Address 1 is an I/O Port : 0000DE00h
> Address 2 is a Memory Address (anywhere in 0-4Gb) : FFEFF000h
> Expansion ROM of 0Kb decoded by this card
>
> Vendor 10ECh Realtek Semiconductor
> Device 8139h RT8139 (A/B/C/813x) Fast Ethernet Adapter
> Command 0105h (I/O Access, BusMaster, System Errors)
> Status 0290h (Has Capabilities List, Supports Back-To-Back Trans.,
> Medium Timing)
> Revision 10h, Header Type 00h, Bus Latency 80h
> Self test 00h (Self test not supported)
> PCI Class Network, type Ethernet
> Subsystem ID 50001799h F5D5000 10/100 Fast Ethernet Adapter
> Subsystem Vendor 1799h Belkin Research and Development Labs
> Address 0 is an I/O Port : 0000DC00h
> Address 1 is a Memory Address (anywhere in 0-4Gb) : FFEFEF00h
> System IRQ 11, INT# A
> Expansion ROM of 0Kb decoded by this card
> New Capabilities List Present:
> Power Management Capability, Version 1.1
> Supports low power State D1
> Supports low power State D2
> Supports PME# from mode(s) D1, D2, D3hot
> Current Power State : D0 (Device operational, no power saving)
>
> ROM PCI IRQ routing table Windows 9x Compatibility Tests....
> No ROM PCI IRQ routing table found!!!
>
> IRQ Summary: IRQs 3,11,14,15 are used by PCI devices
> Shared IRQs: There are no shared PCI IRQs
>
>
>
Anonymous
a b B Homebuilt system
December 3, 2004 12:45:42 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

"David Maynard" <dNOTmayn@ev1.net> a écrit dans le message de
news:10qvlbjf7vvb0c9@corp.supernews.com...
claude wrote:

> I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
> the following message:
>
> "ROM PCI IRQ routing table Windows 9x Compatibility Tests....
> No ROM PCI IRQ routing table found!!!"
>
> Does anyone have an idea about it ?

Your BIOS apparently doesn't have a PCI IRQ Routing Table so Windows will
not be able to dynamically route PCI IRQ assignments.

http://www.microsoft.com/whdc/archive/pciirq.mspx



what's the impact of this missing table ? should I do anything with the BIOS
?
in the following link (http://www.microsoft.com/whdc/archive/pciixa.mspx),
they talk about my chipset (PIIX4 chip set): it would be possible to get the
IRQ routing on my W98SE. I only need to run regedit and update the right
registry. but, I know there's some risk to use regedit....

thanks
Claude
Anonymous
a b B Homebuilt system
December 3, 2004 12:45:43 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

Claude wrote:

> "David Maynard" <dNOTmayn@ev1.net> a écrit dans le message de
> news:10qvlbjf7vvb0c9@corp.supernews.com...
> claude wrote:
>
>
>>I ran PCITEST downloaed from http://ubcd.sourceforge.net/, and, I get
>>the following message:
>>
>>"ROM PCI IRQ routing table Windows 9x Compatibility Tests....
>>No ROM PCI IRQ routing table found!!!"
>>
>>Does anyone have an idea about it ?
>
>
> Your BIOS apparently doesn't have a PCI IRQ Routing Table so Windows will
> not be able to dynamically route PCI IRQ assignments.
>
> http://www.microsoft.com/whdc/archive/pciirq.mspx
>
>
>
> what's the impact of this missing table ?

Judging by the IRQ list you gave, pretty much nothing.

> should I do anything with the BIOS

You could check for a BIOS update.

What motherboard is it anyway?

> ?
> in the following link (http://www.microsoft.com/whdc/archive/pciixa.mspx),
> they talk about my chipset (PIIX4 chip set): it would be possible to get the
> IRQ routing on my W98SE. I only need to run regedit and update the right
> registry. but, I know there's some risk to use regedit....

That page isn't really for users but it suggests that maybe you didn't load
all the motherboard drivers: in particular the miniport driver, if it has one.

>
> thanks
> Claude

Besides you having found this IRQ table message in a diagnostic program,
just exactly what in your system isn't working?
Anonymous
a b B Homebuilt system
December 3, 2004 2:05:40 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

David Maynard a écrit:
>> Your BIOS apparently doesn't have a PCI IRQ Routing Table so Windows will
>> not be able to dynamically route PCI IRQ assignments.
>>
>> http://www.microsoft.com/whdc/archive/pciirq.mspx
>>
>>
>>
>> what's the impact of this missing table ?
>
>
> Judging by the IRQ list you gave, pretty much nothing.
>
>> should I do anything with the BIOS
>
>
> You could check for a BIOS update.

I dit it 3 weeks ago. since this update my dual boot system (w98se,
linux) is instable.
I leave a message here following some concerns I had with the update
program: http://members.driverguide.com/driver/detail.php?driver...
but, I have no answer from them :-(
>
> What motherboard is it anyway?
>
PC Chips - M572. the doc is here :
ftp://ftp.bns-computer.de/bns-computer/SUPPORT/MANUALS/...

here : http://members.driverguide.com/list/company796/page2/in...
there are 2 drivers: one for the bios (M572 Driver) and the other one
for the motherboard (M572 Mainboard Driver). I only use the first one. I
'm not sure i need the 2nd one.

>> in the following link
>> (http://www.microsoft.com/whdc/archive/pciixa.mspx),
>> they talk about my chipset (PIIX4 chip set): it would be possible to
>> get the
>> IRQ routing on my W98SE. I only need to run regedit and update the right
>> registry. but, I know there's some risk to use regedit....
>
>
> That page isn't really for users but it suggests that maybe you didn't
> load all the motherboard drivers: in particular the miniport driver, if
> it has one.
>
how can I check this ?
>
> Besides you having found this IRQ table message in a diagnostic program,
> just exactly what in your system isn't working?
>
for example, I am not able to reinstall linux anymore. I have errors
during the installation.
regarding w98se, I have many difficulties to install network and sound
chipset drivers. before this BIOS update, I was not faced to those concerns.

thanks for yopur help
Claude
Anonymous
a b B Homebuilt system
December 3, 2004 4:43:30 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

David Maynard a écrit:
>
> That page isn't really for users but it suggests that maybe you didn't
> load all the motherboard drivers: in particular the miniport driver, if
> it has one.
>

additional informations :

in the PCI bus properties:
- the stering IRQ properties mention "IRQ table read from the bios with
the help of the real mode interface" and "IRQ miniport has been loaded"...
- the parameters mention : use hardware is crossed and not use bios

thank you for your advices
Claude
Anonymous
a b B Homebuilt system
December 3, 2004 11:28:28 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

claude wrote:
>
>
> David Maynard a écrit:
>
>>> Your BIOS apparently doesn't have a PCI IRQ Routing Table so Windows
>>> will
>>> not be able to dynamically route PCI IRQ assignments.
>>>
>>> http://www.microsoft.com/whdc/archive/pciirq.mspx
>>>
>>>
>>>
>>> what's the impact of this missing table ?
>>
>>
>>
>> Judging by the IRQ list you gave, pretty much nothing.
>>
>>> should I do anything with the BIOS
>>
>>
>>
>> You could check for a BIOS update.
>
>
> I dit it 3 weeks ago. since this update my dual boot system (w98se,
> linux) is instable.
> I leave a message here following some concerns I had with the update
> program: http://members.driverguide.com/driver/detail.php?driver...
> but, I have no answer from them :-(
>
>>
>> What motherboard is it anyway?
>>
> PC Chips - M572. the doc is here :
> ftp://ftp.bns-computer.de/bns-computer/SUPPORT/MANUALS/...
>
> here : http://members.driverguide.com/list/company796/page2/in...
> there are 2 drivers: one for the bios (M572 Driver) and the other one
> for the motherboard (M572 Mainboard Driver). I only use the first one. I
> 'm not sure i need the 2nd one.
>
>>> in the following link
>>> (http://www.microsoft.com/whdc/archive/pciixa.mspx),
>>> they talk about my chipset (PIIX4 chip set): it would be possible to
>>> get the
>>> IRQ routing on my W98SE. I only need to run regedit and update the right
>>> registry. but, I know there's some risk to use regedit....
>>
>>
>>
>> That page isn't really for users but it suggests that maybe you didn't
>> load all the motherboard drivers: in particular the miniport driver,
>> if it has one.
>>
> how can I check this ?
>
>>
>> Besides you having found this IRQ table message in a diagnostic
>> program, just exactly what in your system isn't working?
>>
> for example, I am not able to reinstall linux anymore. I have errors
> during the installation.
> regarding w98se, I have many difficulties to install network and sound
> chipset drivers. before this BIOS update, I was not faced to those
> concerns.
>
> thanks for yopur help
> Claude
>

Well, I see that BIOS file but, other than the person that posted it, I
have no idea where it came from or who made it.

Here's the PCChips downloads for it.

http://www.pcchipsusa.com/support-discontinued-bios.asp...
Anonymous
a b B Homebuilt system
December 4, 2004 1:00:19 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

"David Maynard" <dNOTmayn@ev1.net> a écrit dans le message de
news:10r286o83psqc47@corp.supernews.com...
claude wrote:
>
>> You could check for a BIOS update.
>
>
> I dit it 3 weeks ago. since this update my dual boot system (w98se,
> linux) is instable.
> I leave a message here following some concerns I had with the update
> program: http://members.driverguide.com/driver/detail.php?driver...
> but, I have no answer from them :-(
>
>>
>> What motherboard is it anyway?
>>
> PC Chips - M572. the doc is here :
> ftp://ftp.bns-computer.de/bns-computer/SUPPORT/MANUALS/...
>
> here : http://members.driverguide.com/list/company796/page2/in...
> there are 2 drivers: one for the bios (M572 Driver) and the other one
> for the motherboard (M572 Mainboard Driver). I only use the first one. I
> 'm not sure i need the 2nd one.
>
>>> in the following link
>>> (http://www.microsoft.com/whdc/archive/pciixa.mspx),
>>> they talk about my chipset (PIIX4 chip set): it would be possible to
>>> get the
>>> IRQ routing on my W98SE. I only need to run regedit and update the right
>>> registry. but, I know there's some risk to use regedit....
>>
>>
>>
>> That page isn't really for users but it suggests that maybe you didn't
>> load all the motherboard drivers: in particular the miniport driver,
>> if it has one.
>>
> how can I check this ?
>
>>
>> Besides you having found this IRQ table message in a diagnostic
>> program, just exactly what in your system isn't working?
>>
> for example, I am not able to reinstall linux anymore. I have errors
> during the installation.
> regarding w98se, I have many difficulties to install network and sound
> chipset drivers. before this BIOS update, I was not faced to those
> concerns.
>
> thanks for yopur help
> Claude
>

Well, I see that BIOS file but, other than the person that posted it, I
have no idea where it came from or who made it.

Here's the PCChips downloads for it.

http://www.pcchipsusa.com/support-discontinued-bios.asp...



it's not mine. M572 is the right one
Anonymous
a b B Homebuilt system
December 4, 2004 1:00:20 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

Claude wrote:

> "David Maynard" <dNOTmayn@ev1.net> a écrit dans le message de
> news:10r286o83psqc47@corp.supernews.com...
> claude wrote:
>
>>>You could check for a BIOS update.
>>
>>
>>I dit it 3 weeks ago. since this update my dual boot system (w98se,
>>linux) is instable.
>>I leave a message here following some concerns I had with the update
>>program: http://members.driverguide.com/driver/detail.php?driver...
>>but, I have no answer from them :-(
>>
>>
>>>What motherboard is it anyway?
>>>
>>
>>PC Chips - M572. the doc is here :
>>ftp://ftp.bns-computer.de/bns-computer/SUPPORT/MANUALS/...
>>
>>here : http://members.driverguide.com/list/company796/page2/in...
>>there are 2 drivers: one for the bios (M572 Driver) and the other one
>>for the motherboard (M572 Mainboard Driver). I only use the first one. I
>>'m not sure i need the 2nd one.
>>
>>
>>>>in the following link
>>>>(http://www.microsoft.com/whdc/archive/pciixa.mspx),
>>>>they talk about my chipset (PIIX4 chip set): it would be possible to
>>>>get the
>>>>IRQ routing on my W98SE. I only need to run regedit and update the right
>>>>registry. but, I know there's some risk to use regedit....
>>>
>>>
>>>
>>>That page isn't really for users but it suggests that maybe you didn't
>>>load all the motherboard drivers: in particular the miniport driver,
>>>if it has one.
>>>
>>
>>how can I check this ?
>>
>>
>>>Besides you having found this IRQ table message in a diagnostic
>>>program, just exactly what in your system isn't working?
>>>
>>
>>for example, I am not able to reinstall linux anymore. I have errors
>>during the installation.
>>regarding w98se, I have many difficulties to install network and sound
>>chipset drivers. before this BIOS update, I was not faced to those
>>concerns.
>>
>>thanks for yopur help
>>Claude
>>
>
>
> Well, I see that BIOS file but, other than the person that posted it, I
> have no idea where it came from or who made it.
>
> Here's the PCChips downloads for it.
>
> http://www.pcchipsusa.com/support-discontinued-bios.asp...
>
>
>
> it's not mine. M572 is the right one
>
>

What do you mean "it's not mine?"

Product Name Type of chipset Bios Type Bios File Name
M572/
M572A/
Intel i430 TX AMI M572 BIOS File: 5728B27.ZIP (11/27/98,
115KB)
Anonymous
a b B Homebuilt system
December 4, 2004 6:14:23 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

David Maynard a écrit:

>>
>> Well, I see that BIOS file but, other than the person that posted it, I
>> have no idea where it came from or who made it.
>>
>> Here's the PCChips downloads for it.
>>
>> http://www.pcchipsusa.com/support-discontinued-bios.asp...
>>
>>
>>
>> it's not mine. M572 is the right one
>>
>>
>
> What do you mean "it's not mine?"
>
> Product Name Type of chipset Bios Type Bios File Name
> M572/
> M572A/
> Intel i430 TX AMI M572 BIOS File: 5728B27.ZIP
> (11/27/98, 115KB)
>


Sorry, I was not precise enough. M550 isn't my mobo. it is M572
(http://motherboards.mbarron.net/models/pcchips/m572.htm ). here, you
can find the ID of my mobo before the BIOS upgrade:
51-1216-001437-00111110-071595-I430TX-001_10_TX-H. with this ID, you can
find the BIOS program (990224S.exe) that I use to flash my BIOS.
you can find it there:
http://members.driverguide.com/driver/detail.php?driver... . you
can notice the ID is exactly the same.

on the website you send,
http://www.pcchipsusa.com/support-discontinued-bios.asp..., there is
the 5728b27.zip which contains only 1 file: 5721127.rom. No boot file
like aminfxxxx.exe. I ask on driverguide website why there are 2 files
on their website. but, I have no answer.

I don't know what to do. I cannot find again my old bios (971216S.ROM).
i would be sure i use the right program (990224S.exe) for my bios.

thanks
Claude
Anonymous
a b B Homebuilt system
December 4, 2004 8:45:51 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

claude wrote:

>
>
> David Maynard a écrit:
>
>>>
>>> Well, I see that BIOS file but, other than the person that posted it, I
>>> have no idea where it came from or who made it.
>>>
>>> Here's the PCChips downloads for it.
>>>
>>> http://www.pcchipsusa.com/support-discontinued-bios.asp...
>>>
>>>
>>>
>>> it's not mine. M572 is the right one
>>>
>>>
>>
>> What do you mean "it's not mine?"
>>
>> Product Name Type of chipset Bios Type Bios File Name M572/
>> M572A/
>> Intel i430 TX AMI M572 BIOS File: 5728B27.ZIP
>> (11/27/98, 115KB)
>>
>
>
> Sorry, I was not precise enough. M550 isn't my mobo. it is M572

I understand that. What I don't understand is why you think "M572 BIOS
File: 5728B27.ZIP" means M550.

There are three listed:

M572 BIOS File : 5728B27.ZIP (11/27/98, 115KB) ... for the M572

M572A BIOS File : 572A0630.ZIP (6/30/98, 115KB)... for the M572A

M550 BIOS File : 5501117S.ZIP (11/17/97, 124KB)... for the M550

Obviously, if you have an M572 you use the one for the M572.

> (http://motherboards.mbarron.net/models/pcchips/m572.htm ). here, you
> can find the ID of my mobo before the BIOS upgrade:
> 51-1216-001437-00111110-071595-I430TX-001_10_TX-H. with this ID,

What I don't see is what version your board is. Look for a version number
near where keyboard plugs in e.g. V 1.2, or 2.5. etc.

> you can
> find the BIOS program (990224S.exe) that I use to flash my BIOS.
> you can find it there:
> http://members.driverguide.com/driver/detail.php?driver... . you
> can notice the ID is exactly the same.

Yes, I notice. But I don't know where it came from or who made it or what
it was supposed to 'fix'. And I don't know if they did it right. But since
you have problems with it...


> on the website you send,
> http://www.pcchipsusa.com/support-discontinued-bios.asp..., there is
> the 5728b27.zip which contains only 1 file: 5721127.rom. No boot file

It is typical for mobo manufacturers to place only the BIOS image itself in
the 'BIOS' download and the flash program in a separate download.


> like aminfxxxx.exe. I ask on driverguide website why there are 2 files
> on their website. but, I have no answer.

It's the flash program.


> I don't know what to do. I cannot find again my old bios (971216S.ROM).

Neither can I. It's so old that it doesn't show up on any 'update' lists.

> i would be sure i use the right program (990224S.exe) for my bios.
>
> thanks
> Claude
>

Try here. http://bns-computer.de/Support/mb_572.htm

It's in german but decipherable and they have a BIOS update for the M572
later than that outdated PCChips page (which I found through a back door as
they no longer list the M572 ANY where on their site the 'normal' way). The
24.02.99 5720224s.rom (same as the 990224S.exe BIOS) notes say it fixes
drives > 8.4 gig. (page also has the flash utility as a separate download,
like I mentioned).

Or, you can pick any previous version.

I also found this patched version of the 990224S for enabling
K6-II+/K6-III+ processors (I used a similar patched BIOS on my now dead
M571 and it worked fine). Their patched BIOS refers to the 990224S as the
'original' source they used to patch and create their 990224SJ.ZIP version.

http://web.inter.nl.net/hcc/J.Steunebrink/k6plus.htm


After all that it kind of makes me think it isn't the BIOS that's your
problem. Did you clear CMOS after the flash?
Anonymous
a b B Homebuilt system
December 5, 2004 6:46:45 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

"David Maynard" <dNOTmayn@ev1.net> a écrit dans le message de
news:10r4j1ppehp4b0b@corp.supernews.com...
claude wrote:

>
> Sorry, I was not precise enough. M550 isn't my mobo. it is M572

I understand that. What I don't understand is why you think "M572 BIOS
File: 5728B27.ZIP" means M550.

no, I don't. I only say that I found, on driverguibe website, 2 files
matching my M572 : 5728B27.ZIP and 990224S.exe. I used the 2nd one. but, I
hope it's the right one fitting my bios.


> (http://motherboards.mbarron.net/models/pcchips/m572.htm ). here, you
> can find the ID of my mobo before the BIOS upgrade:
> 51-1216-001437-00111110-071595-I430TX-001_10_TX-H. with this ID,

What I don't see is what version your board is. Look for a version number
near where keyboard plugs in e.g. V 1.2, or 2.5. etc.

I don't understand what you mean with "keyboard plugs". where can I find
this number ?


Try here. http://bns-computer.de/Support/mb_572.htm

It's in german but decipherable and they have a BIOS update for the M572
later than that outdated PCChips page (which I found through a back door as
they no longer list the M572 ANY where on their site the 'normal' way).

I know this site, but, as you say, with a "normal way" - as I did -, I was
not able to find those informations.


The 24.02.99 5720224s.rom (same as the 990224S.exe BIOS) notes say it
fixes
drives > 8.4 gig. (page also has the flash utility as a separate download,
like I mentioned).

do you think I can use the 5720224s.rom without fear ? If I face to
concerns, I 'll be able to use the 990224S.exe to go back to the current
bios. correct ?
do I use amifl815.exe or amifl634.com ?

Or, you can pick any previous version.

I also found this patched version of the 990224S for enabling
K6-II+/K6-III+ processors (I used a similar patched BIOS on my now dead
M571 and it worked fine). Their patched BIOS refers to the 990224S as the
'original' source they used to patch and create their 990224SJ.ZIP version.

http://web.inter.nl.net/hcc/J.Steunebrink/k6plus.htm


But, as you know, neither I have K6-II+/K6-III+ processors nor AMD.


After all that it kind of makes me think it isn't the BIOS that's your
problem. Did you clear CMOS after the flash?

Yes, I did. I can clear again ?

thanks a lot for all those infos !!
Claude
Anonymous
a b B Homebuilt system
December 5, 2004 11:37:41 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

Claude wrote:

> "David Maynard" <dNOTmayn@ev1.net> a écrit dans le message de
> news:10r4j1ppehp4b0b@corp.supernews.com...
> claude wrote:
>
>
>>Sorry, I was not precise enough. M550 isn't my mobo. it is M572
>
>
> I understand that. What I don't understand is why you think "M572 BIOS
> File: 5728B27.ZIP" means M550.
>
> no, I don't.

Then why do you keep saying "M550 isn't my mobo"?

> I only say that I found, on driverguibe website, 2 files
> matching my M572 : 5728B27.ZIP and 990224S.exe. I used the 2nd one. but, I
> hope it's the right one fitting my bios.

They both 'fit'. They're different releases at different times. "990224S"
is apparently the 'newest' and last one they released.


>>(http://motherboards.mbarron.net/models/pcchips/m572.htm ). here, you
>>can find the ID of my mobo before the BIOS upgrade:
>>51-1216-001437-00111110-071595-I430TX-001_10_TX-H. with this ID,
>
>
> What I don't see is what version your board is. Look for a version number
> near where keyboard plugs in e.g. V 1.2, or 2.5. etc.
>
> I don't understand what you mean with "keyboard plugs". where can I find
> this number ?

You have a keyboard. It plugs into the motherboard. Look where it plugs in.


> Try here. http://bns-computer.de/Support/mb_572.htm
>
> It's in german but decipherable and they have a BIOS update for the M572
> later than that outdated PCChips page (which I found through a back door as
> they no longer list the M572 ANY where on their site the 'normal' way).
>
> I know this site, but, as you say, with a "normal way" - as I did -, I was
> not able to find those informations.
>
>
> The 24.02.99 5720224s.rom (same as the 990224S.exe BIOS) notes say it
> fixes
> drives > 8.4 gig. (page also has the flash utility as a separate download,
> like I mentioned).
>
> do you think I can use the 5720224s.rom without fear ? If I face to
> concerns, I 'll be able to use the 990224S.exe to go back to the current
> bios. correct ?

They're the same BIOS (or are supposed to be) but I trust that the
5720224s.rom is 'official' while I am not so sure about stuff submitted by
lord knows who on the various flavors of drivers.com


> do I use amifl815.exe or amifl634.com ?

I'm not on that page any more but, barring a note on it to the contrary,
I'd use the later version, meaning amifl815.exe.

>
> Or, you can pick any previous version.
>
> I also found this patched version of the 990224S for enabling
> K6-II+/K6-III+ processors (I used a similar patched BIOS on my now dead
> M571 and it worked fine). Their patched BIOS refers to the 990224S as the
> 'original' source they used to patch and create their 990224SJ.ZIP version.
>
> http://web.inter.nl.net/hcc/J.Steunebrink/k6plus.htm
>
>
> But, as you know, neither I have K6-II+/K6-III+ processors nor AMD.

Doesn't matter. It supports all the same ones, PLUS the K6-II+/III+ processors.


> After all that it kind of makes me think it isn't the BIOS that's your
> problem. Did you clear CMOS after the flash?
>
> Yes, I did. I can clear again ?

Unplug the machine and reset CMOS for a couple of minutes; then put the
jumper back to normal.

>
> thanks a lot for all those infos !!
> Claude
>
>
Anonymous
a b B Homebuilt system
December 6, 2004 10:50:11 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

David Maynard a écrit:
> Claude wrote:
>
> Then why do you keep saying "M550 isn't my mobo"?
>

it's a misunderstanding of myself. let's stop with M550.

>
>> What I don't see is what version your board is. Look for a version number
>> near where keyboard plugs in e.g. V 1.2, or 2.5. etc.
>>
>> I don't understand what you mean with "keyboard plugs". where can I find
>> this number ?
>
>
> You have a keyboard. It plugs into the motherboard. Look where it plugs in.

Outside of my PC: It plugs on DB-9 serial port behind my PC. Nothing is
written around. On the left, I have the mouse plug, and, on the right,
the parallelle port.
Does I need to look inside of my PC ? on the mobo ?

>
> Unplug the machine and reset CMOS for a couple of minutes; then put the
> jumper back to normal.
>

ok. I will do that in the next days and keep you inform of the results.

Thanks a lot !

Claude
Anonymous
a b B Homebuilt system
December 6, 2004 10:50:12 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

claude wrote:

> David Maynard a écrit:
>
>> Claude wrote:
>>
>> Then why do you keep saying "M550 isn't my mobo"?
>>
>
> it's a misunderstanding of myself. let's stop with M550.
>
>>
>>> What I don't see is what version your board is. Look for a version
>>> number
>>> near where keyboard plugs in e.g. V 1.2, or 2.5. etc.
>>>
>>> I don't understand what you mean with "keyboard plugs". where can I find
>>> this number ?
>>
>>
>>
>> You have a keyboard. It plugs into the motherboard. Look where it
>> plugs in.
>
>
> Outside of my PC: It plugs on DB-9 serial port behind my PC.

Either you have the strangest self modified keyboard I've heard of yet or
you can't possibly mean your keyboard is on a DB9 serial port.

Doesn't matter. When I say where the keyboard plugs in I mean where the
motherboard expects it to plug in. The ROUND connector.

> Nothing is
> written around. On the left, I have the mouse plug, and, on the right,
> the parallelle port.
> Does I need to look inside of my PC ? on the mobo ?

YES inside on the mobo.

>
>>
>> Unplug the machine and reset CMOS for a couple of minutes; then put
>> the jumper back to normal.
>>
>
> ok. I will do that in the next days and keep you inform of the results.
>
> Thanks a lot !
>
> Claude
>
Anonymous
a b B Homebuilt system
December 7, 2004 9:17:08 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

David Maynard a écrit:

>>
>> Outside of my PC: It plugs on DB-9 serial port behind my PC.
>
>
> Either you have the strangest self modified keyboard I've heard of yet
> or you can't possibly mean your keyboard is on a DB9 serial port.

of course, you're right: I reversed the plugs... sorry.

>> Does I need to look inside of my PC ? on the mobo ?
>
>
> YES inside on the mobo.
>
OK. but, I've to take off my mobo. if not, it's impossible to see something.

Thanks a lot !

Claude
>>
>
Anonymous
a b B Homebuilt system
December 14, 2004 7:37:54 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

David Maynard a écrit:

>
>>
>>>
>>> Unplug the machine and reset CMOS for a couple of minutes; then put
>>> the jumper back to normal.
>>>

I flashed the bios with the 5720224s.rom and amifl815.exe programs. the
results are exactly the same, got, before, with 990224s.rom

I also clear CMOS.

Hereunder, you can read one part of the the Aida32 results :

--------[ AIDA32 (c) 1995-2004 Tamas Miklos
]---------------------------------------------------------------------------

Version AIDA32 v3.94.2
Auteur
tamas.miklos@aida32.hu
Site web http://www.aida32.hu
Type de rapport Générateur de
rapports Pro/Lite
Ordinateur ADAGIO (Pentrium II)
Générateur claude
Système d'exploitation Microsoft Windows
98 SE 4.10.2222A (Win98 SE)
Date 1980-01-04
Heure 15:29


--------[ Résumé
]------------------------------------------------------------------------------------------------------

Ordinateur:
Système d'exploitation Microsoft
Windows 98 SE
Service Pack du système Aucun
Internet Explorer 6.0.2800.1106
(IE 6.0 SP1)
Nom du système ADAGIO
(Pentrium II)
Nom d'utilisateur claude

Carte mère:
Type de processeur Intel Pentium
MMX, 233 MHz
Nom de la carte mère Inconnu
Chipset de la carte mère Intel Triton
82430TX
Mémoire système 256 Mo (SDRAM)
Type de BIOS AMI (07/15/95)
Port de communication Port de
communication (COM1)
Port de communication Port de
communication (COM2)
Port de communication Port imprimante
(LPT1)

Moniteur:
Carte vidéo ATI Rage II+
PCI (ati_m64) (2 Mo)
Accélérateur 3D ATI 3D-Rage II+
Moniteur ViewSonic
VP171b (A1U040600116)

Multimédia:
Carte audio C-Media CMI8330
Audio Adapter


--------[ Processeur
]--------------------------------------------------------------------------------------------------

Propriétés du CPU:
Type de processeur Intel Pentium
MMX, 233 MHz
Alias du CPU P55C, A80503
CPU Stepping xB1
Cache de code de niveau 1 16 Ko
Cache de données de niveau 1 16 Ko
Cache de niveau 2 0

Informations physiques sur le CPU:
Forme du composant 296 Pin PGA
Taille du composant 4.95 cm x 4.95 cm
Transistors 4.5 million(s)
Technologie utilisée 4M, 0.28 um, CMOS
Taille interne 140 / 128 mm2
Voltage au coeur 2.8 V
Voltage d'entrée/sortie 3.3 V
Puissance typique 6.1 - 7.9 W
(dépendant de la vitesse d'horloge)
Puissance maximale 13.1 - 17 W
(dépendant de la vitesse d'horloge)

Fabricant du processeur:
Nom de l'entreprise Intel Corporation
Information sur le produit
http://www.intel.com/products/browse/processor.htm

Utilisation du CPU:
CPU nº1 0 %

Problèmes et suggestions:
Problème Aucun cache de
niveau 2 trouvé sur le CPU. Cela peut entraîner une dégradation des
performances.


--------[ CPUID
]-------------------------------------------------------------------------------------------------------

(CPUID) Propriétés:
(CPUID) Fabricant GenuineIntel
(CPUID) Révision 0543h
Identifiant de la plate-forme 00h (Inconnu)
(IA) Numéro de série du CPU Inconnu

Jeu d'instructions:
AMD 3DNow! Non géré
AMD 3DNow! Professional Non géré
AMD Enhanced 3DNow! Non géré
AMD Extended MMX Non géré
AMD64 Non géré
Cyrix Extended MMX Non géré
IA-64 Non géré
IA MMX Géré
IA SSE Non géré
IA SSE 2 Non géré
IA SSE 3 Non géré
Instruction CLFLUSH Non géré
Instruction CMPXCHG8B Géré
Instruction CMPXCHG16B Non géré
Instruction Conditional Move Non géré
Instruction FEMMS Non géré
Instruction MONITOR / MWAIT Non géré

(CPUID) Fonctionnalités:
36-bit Page Size Extension Non géré
Advanced Cryptography Engine Non géré
Alternate Instruction Set Non géré
Automatic Clock Control Non géré
CPL Qualified Debug Store Non géré
Debug Trace Store Non géré
Debugging Extension Géré
Enhanced SpeedStep Technology Non géré
Fast Save & Restore Non géré
Fast System Call Non géré
Hyper-Threading Technology Non géré
L1 Context ID Non géré
Local APIC On Chip Non géré
LongRun Non géré
LongRun Table Interface Non géré
Machine-Check Architecture Non géré
Machine-Check Exception Géré
Memory Type Range Registers Non géré
Model Specific Registers Géré
No-Execute Page Protection Non géré
Page Attribute Table Non géré
Page Global Extension Non géré
Page Size Extension Géré
Pending Break Event Non géré
Physical Address Extension Non géré
Processor Duty Cycle Control Non géré
Processor Serial Number Non géré
Random Number Generator Non géré
Self-Snoop Non géré
Thermal Monitor Non géré
Thermal Monitor 2 Non géré
Time Stamp Counter Géré
Virtual Mode Extension Géré

Problèmes et suggestions:
Suggestion SSE n'est pas
géré sur ce système. Mettez à jour votre processeur pour tirer parti des
extensions SSE dans les applications qui les utilisent.


--------[ Carte mère
]--------------------------------------------------------------------------------------------------

Propriétés de la carte mère:
Identifiant de la carte mère
51-0224-001437-00101111-071595-572$M572-V1.28679Release 02/24/1999 S
Nom de la carte mère Inconnu


--------[ Mémoire
]-----------------------------------------------------------------------------------------------------

Mémoire physique:
Total 255 Mo
Utilisé 135 Mo
Disponible 119 Mo
Utilisation 53 %

Zone de swap:
Total 358 Mo
Utilisé 80 Mo
Disponible 278 Mo
Utilisation 22 %

Mémoire virtuelle:
Total 614 Mo
Utilisé 216 Mo
Disponible 398 Mo
Utilisation 35 %

Problèmes et suggestions:
Suggestion Installez
davantage de mémoire système pour améliorer les performances des
applications.


--------[ Chipset
]-----------------------------------------------------------------------------------------------------

Propriétés du chipset:
Chipset de la carte mère Intel Triton
82430TX
CAS Latency 3T
RAS To CAS Delay 3T
RAS Precharge 3T
RAS Active Time 5T
Taille du cache externe 512 Ko
Type du cache externe Dual-Bank
Pipelined Burst
État du cache externe Activé

Slots mémoire:
Slot DRAM nº1 128 Mo (SDRAM)
Slot DRAM nº2 128 Mo (SDRAM)

Fabricant du chipset:
Nom de l'entreprise Intel Corporation
Information sur le produit
http://www.intel.com/products/browse/chipsets.htm
Télécharger le pilote
http://support.intel.com/support/chipsets/index.htm


--------[ BIOS
]--------------------------------------------------------------------------------------------------------

Propriétés du BIOS:
Type de BIOS AMI
Date du BIOS système 07/15/95
Date du BIOS vidéo 97/08/22

Fabricant du BIOS:
Nom de l'entreprise American
Megatrends Inc.
Information sur le produit
http://www.ami.com/amibios


--------[ Vidéo Windows
--------------------------------------------------------------------------

[ ATI Rage II+ PCI (ati_m64) ]

Propriétés de la carte vidéo:
Description du périphérique ATI Rage II+
PCI (ati_m64)
Type de circuit Mach64: Rage II+
Type de DAC Interne
Pilotes installés ati_m64.drv
Taille de la mémoire 2 Mo

Fabricant de la carte vidéo:
Nom de l'entreprise ATI
Technologies Inc.
Information sur le produit
http://www.ati.com/products/home-office.html
Télécharger le pilote
http://www.ati.com/support/driver.html

Problèmes et suggestions:
Problème Il y a moins de
4 Mo de mémoire vidéo installés. Mettez à jour votre carte vidéo pour
obtenir de meilleures performances.


--------[ Vidéo PCI/AGP
]-----------------------------------------------------------------------------------------------

ATI 3D-Rage II+
Carte vidéo
ATI 3D-Rage II+
Accélérateur 3D


--------[ Moniteur
]----------------------------------------------------------------------------------------------------

[ ViewSonic VP171b ]

Propriétés du moniteur:
Nom du moniteur ViewSonic VP171b
Identification du moniteur VSC0C11
Modèle VP171b
Date de fabrication Semaine 6 / 2004
Numéro de série A1U040600116
Taille d'affichage maximale visible 34 cm x 27 cm
(17.1")
Ratio d'aspect de l'image 4:3
Fréquence horizontale 30 - 82 KHz
Fréquence verticale 50 - 75 Hz
Résolution maximale 1280 x 1024
Gamma 2.20
Gestion du mode DPMS Active-Off

Modes vidéo gérés:
640 x 480 75 Hz
800 x 600 75 Hz
1024 x 768 75 Hz
1152 x 864 75 Hz
1280 x 1024 75 Hz

Fabricant du moniteur:
Nom de l'entreprise ViewSonic
Corporation
Information sur le produit
http://www.viewsonic.com/products/desktop_display.htm
Télécharger le pilote
http://www.viewsonic.com/support/drivers.htm

==============================================================================

what's the video BIOS ? Is there any upgrade I could do ?

what's the cache level 2 ?


Thanks a lot !

Claude
December 14, 2004 7:37:55 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

have you loaded the motherboard drivers for the chipset? CD that came with
the board...

"Claude" <nospam@nospam.fr> wrote in message
news:41BF08D2.4080502@nospam.fr...
> David Maynard a écrit:
>
> >
> >>
> >>>
> >>> Unplug the machine and reset CMOS for a couple of minutes; then put
> >>> the jumper back to normal.
> >>>
>
> I flashed the bios with the 5720224s.rom and amifl815.exe programs. the
> results are exactly the same, got, before, with 990224s.rom
>
> I also clear CMOS.
>
> Hereunder, you can read one part of the the Aida32 results :
>
> --------[ AIDA32 (c) 1995-2004 Tamas Miklos
> ]-------------------------------------------------------------------------
--
>
> Version AIDA32 v3.94.2
> Auteur
> tamas.miklos@aida32.hu
> Site web
http://www.aida32.hu
> Type de rapport Générateur de
> rapports Pro/Lite
> Ordinateur ADAGIO (Pentrium
II)
> Générateur claude
> Système d'exploitation Microsoft Windows
> 98 SE 4.10.2222A (Win98 SE)
> Date 1980-01-04
> Heure 15:29
>
>
> --------[ Résumé
> ]-------------------------------------------------------------------------
-----------------------------
>
> Ordinateur:
> Système d'exploitation Microsoft
> Windows 98 SE
> Service Pack du système Aucun
> Internet Explorer 6.0.2800.1106
> (IE 6.0 SP1)
> Nom du système ADAGIO
> (Pentrium II)
> Nom d'utilisateur claude
>
> Carte mère:
> Type de processeur Intel Pentium
> MMX, 233 MHz
> Nom de la carte mère Inconnu
> Chipset de la carte mère Intel Triton
> 82430TX
> Mémoire système 256 Mo (SDRAM)
> Type de BIOS AMI (07/15/95)
> Port de communication Port de
> communication (COM1)
> Port de communication Port de
> communication (COM2)
> Port de communication Port imprimante
> (LPT1)
>
> Moniteur:
> Carte vidéo ATI Rage II+
> PCI (ati_m64) (2 Mo)
> Accélérateur 3D ATI 3D-Rage II+
> Moniteur ViewSonic
> VP171b (A1U040600116)
>
> Multimédia:
> Carte audio C-Media CMI8330
> Audio Adapter
>
>
> --------[ Processeur
> ]-------------------------------------------------------------------------
-------------------------
>
> Propriétés du CPU:
> Type de processeur Intel Pentium
> MMX, 233 MHz
> Alias du CPU P55C, A80503
> CPU Stepping xB1
> Cache de code de niveau 1 16 Ko
> Cache de données de niveau 1 16 Ko
> Cache de niveau 2 0
>
> Informations physiques sur le CPU:
> Forme du composant 296 Pin PGA
> Taille du composant 4.95 cm x 4.95 cm
> Transistors 4.5 million(s)
> Technologie utilisée 4M, 0.28 um, CMOS
> Taille interne 140 / 128 mm2
> Voltage au coeur 2.8 V
> Voltage d'entrée/sortie 3.3 V
> Puissance typique 6.1 - 7.9 W
> (dépendant de la vitesse d'horloge)
> Puissance maximale 13.1 - 17 W
> (dépendant de la vitesse d'horloge)
>
> Fabricant du processeur:
> Nom de l'entreprise Intel Corporation
> Information sur le produit
> http://www.intel.com/products/browse/processor.htm
>
> Utilisation du CPU:
> CPU nº1 0 %
>
> Problèmes et suggestions:
> Problème Aucun cache de
> niveau 2 trouvé sur le CPU. Cela peut entraîner une dégradation des
> performances.
>
>
> --------[ CPUID
> ]-------------------------------------------------------------------------
------------------------------
>
> (CPUID) Propriétés:
> (CPUID) Fabricant GenuineIntel
> (CPUID) Révision 0543h
> Identifiant de la plate-forme 00h (Inconnu)
> (IA) Numéro de série du CPU Inconnu
>
> Jeu d'instructions:
> AMD 3DNow! Non géré
> AMD 3DNow! Professional Non géré
> AMD Enhanced 3DNow! Non géré
> AMD Extended MMX Non géré
> AMD64 Non géré
> Cyrix Extended MMX Non géré
> IA-64 Non géré
> IA MMX Géré
> IA SSE Non géré
> IA SSE 2 Non géré
> IA SSE 3 Non géré
> Instruction CLFLUSH Non géré
> Instruction CMPXCHG8B Géré
> Instruction CMPXCHG16B Non géré
> Instruction Conditional Move Non géré
> Instruction FEMMS Non géré
> Instruction MONITOR / MWAIT Non géré
>
> (CPUID) Fonctionnalités:
> 36-bit Page Size Extension Non géré
> Advanced Cryptography Engine Non géré
> Alternate Instruction Set Non géré
> Automatic Clock Control Non géré
> CPL Qualified Debug Store Non géré
> Debug Trace Store Non géré
> Debugging Extension Géré
> Enhanced SpeedStep Technology Non géré
> Fast Save & Restore Non géré
> Fast System Call Non géré
> Hyper-Threading Technology Non géré
> L1 Context ID Non géré
> Local APIC On Chip Non géré
> LongRun Non géré
> LongRun Table Interface Non géré
> Machine-Check Architecture Non géré
> Machine-Check Exception Géré
> Memory Type Range Registers Non géré
> Model Specific Registers Géré
> No-Execute Page Protection Non géré
> Page Attribute Table Non géré
> Page Global Extension Non géré
> Page Size Extension Géré
> Pending Break Event Non géré
> Physical Address Extension Non géré
> Processor Duty Cycle Control Non géré
> Processor Serial Number Non géré
> Random Number Generator Non géré
> Self-Snoop Non géré
> Thermal Monitor Non géré
> Thermal Monitor 2 Non géré
> Time Stamp Counter Géré
> Virtual Mode Extension Géré
>
> Problèmes et suggestions:
> Suggestion SSE n'est pas
> géré sur ce système. Mettez à jour votre processeur pour tirer parti des
> extensions SSE dans les applications qui les utilisent.
>
>
> --------[ Carte mère
> ]-------------------------------------------------------------------------
-------------------------
>
> Propriétés de la carte mère:
> Identifiant de la carte mère
> 51-0224-001437-00101111-071595-572$M572-V1.28679Release 02/24/1999 S
> Nom de la carte mère Inconnu
>
>
> --------[ Mémoire
> ]-------------------------------------------------------------------------
----------------------------
>
> Mémoire physique:
> Total 255 Mo
> Utilisé 135 Mo
> Disponible 119 Mo
> Utilisation 53 %
>
> Zone de swap:
> Total 358 Mo
> Utilisé 80 Mo
> Disponible 278 Mo
> Utilisation 22 %
>
> Mémoire virtuelle:
> Total 614 Mo
> Utilisé 216 Mo
> Disponible 398 Mo
> Utilisation 35 %
>
> Problèmes et suggestions:
> Suggestion Installez
> davantage de mémoire système pour améliorer les performances des
> applications.
>
>
> --------[ Chipset
> ]-------------------------------------------------------------------------
----------------------------
>
> Propriétés du chipset:
> Chipset de la carte mère Intel Triton
> 82430TX
> CAS Latency 3T
> RAS To CAS Delay 3T
> RAS Precharge 3T
> RAS Active Time 5T
> Taille du cache externe 512 Ko
> Type du cache externe Dual-Bank
> Pipelined Burst
> État du cache externe Activé
>
> Slots mémoire:
> Slot DRAM nº1 128 Mo (SDRAM)
> Slot DRAM nº2 128 Mo (SDRAM)
>
> Fabricant du chipset:
> Nom de l'entreprise Intel Corporation
> Information sur le produit
> http://www.intel.com/products/browse/chipsets.htm
> Télécharger le pilote
> http://support.intel.com/support/chipsets/index.htm
>
>
> --------[ BIOS
> ]-------------------------------------------------------------------------
-------------------------------
>
> Propriétés du BIOS:
> Type de BIOS AMI
> Date du BIOS système 07/15/95
> Date du BIOS vidéo 97/08/22
>
> Fabricant du BIOS:
> Nom de l'entreprise American
> Megatrends Inc.
> Information sur le produit
> http://www.ami.com/amibios
>
>
> --------[ Vidéo Windows
> --------------------------------------------------------------------------
>
> [ ATI Rage II+ PCI (ati_m64) ]
>
> Propriétés de la carte vidéo:
> Description du périphérique ATI Rage II+
> PCI (ati_m64)
> Type de circuit Mach64: Rage II+
> Type de DAC Interne
> Pilotes installés ati_m64.drv
> Taille de la mémoire 2 Mo
>
> Fabricant de la carte vidéo:
> Nom de l'entreprise ATI
> Technologies Inc.
> Information sur le produit
> http://www.ati.com/products/home-office.html
> Télécharger le pilote
> http://www.ati.com/support/driver.html
>
> Problèmes et suggestions:
> Problème Il y a moins de
> 4 Mo de mémoire vidéo installés. Mettez à jour votre carte vidéo pour
> obtenir de meilleures performances.
>
>
> --------[ Vidéo PCI/AGP
> ]-------------------------------------------------------------------------
----------------------
>
> ATI 3D-Rage II+
> Carte vidéo
> ATI 3D-Rage II+
> Accélérateur 3D
>
>
> --------[ Moniteur
> ]-------------------------------------------------------------------------
---------------------------
>
> [ ViewSonic VP171b ]
>
> Propriétés du moniteur:
> Nom du moniteur ViewSonic VP171b
> Identification du moniteur VSC0C11
> Modèle VP171b
> Date de fabrication Semaine 6 / 2004
> Numéro de série A1U040600116
> Taille d'affichage maximale visible 34 cm x 27 cm
> (17.1")
> Ratio d'aspect de l'image 4:3
> Fréquence horizontale 30 - 82 KHz
> Fréquence verticale 50 - 75 Hz
> Résolution maximale 1280 x 1024
> Gamma 2.20
> Gestion du mode DPMS Active-Off
>
> Modes vidéo gérés:
> 640 x 480 75 Hz
> 800 x 600 75 Hz
> 1024 x 768 75 Hz
> 1152 x 864 75 Hz
> 1280 x 1024 75 Hz
>
> Fabricant du moniteur:
> Nom de l'entreprise ViewSonic
> Corporation
> Information sur le produit
> http://www.viewsonic.com/products/desktop_display.htm
> Télécharger le pilote
> http://www.viewsonic.com/support/drivers.htm
>
>
============================================================================
==
>
> what's the video BIOS ? Is there any upgrade I could do ?
>
> what's the cache level 2 ?
>
>
> Thanks a lot !
>
> Claude
>
>
>
Anonymous
a b B Homebuilt system
December 14, 2004 9:31:15 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

I never had any CD for my mobo. my PC is not a brand like HP, Compaq ...
where can I find those drivers ?

thx
Claude

JAD a écrit:
> have you loaded the motherboard drivers for the chipset? CD that came with
> the board...
>
> "Claude" <nospam@nospam.fr> wrote in message
> news:41BF08D2.4080502@nospam.fr...
>
>>David Maynard a écrit:
>>
>>
>>>>>Unplug the machine and reset CMOS for a couple of minutes; then put
>>>>>the jumper back to normal.
>>>>>
>>>>
>>I flashed the bios with the 5720224s.rom and amifl815.exe programs. the
>>results are exactly the same, got, before, with 990224s.rom
>>
>>I also clear CMOS.
>>
>>Hereunder, you can read one part of the the Aida32 results :
>>
>>--------[ AIDA32 (c) 1995-2004 Tamas Miklos
>>]-------------------------------------------------------------------------
>
> --
>
>> Version AIDA32 v3.94.2
>> Auteur
>>tamas.miklos@aida32.hu
>> Site web
>
> http://www.aida32.hu
>
>> Type de rapport Générateur de
>>rapports Pro/Lite
>> Ordinateur ADAGIO (Pentrium
>
> II)
>
>> Générateur claude
>> Système d'exploitation Microsoft Windows
>>98 SE 4.10.2222A (Win98 SE)
>> Date 1980-01-04
>> Heure 15:29
>>
>>
>>--------[ Résumé
>>]-------------------------------------------------------------------------
>
> -----------------------------
>
>> Ordinateur:
>> Système d'exploitation Microsoft
>>Windows 98 SE
>> Service Pack du système Aucun
>> Internet Explorer 6.0.2800.1106
>>(IE 6.0 SP1)
>> Nom du système ADAGIO
>>(Pentrium II)
>> Nom d'utilisateur claude
>>
>> Carte mère:
>> Type de processeur Intel Pentium
>>MMX, 233 MHz
>> Nom de la carte mère Inconnu
>> Chipset de la carte mère Intel Triton
>>82430TX
>> Mémoire système 256 Mo (SDRAM)
>> Type de BIOS AMI (07/15/95)
>> Port de communication Port de
>>communication (COM1)
>> Port de communication Port de
>>communication (COM2)
>> Port de communication Port imprimante
>>(LPT1)
>>
>> Moniteur:
>> Carte vidéo ATI Rage II+
>>PCI (ati_m64) (2 Mo)
>> Accélérateur 3D ATI 3D-Rage II+
>> Moniteur ViewSonic
>>VP171b (A1U040600116)
>>
>> Multimédia:
>> Carte audio C-Media CMI8330
>>Audio Adapter
>>
>>
>>--------[ Processeur
>>]-------------------------------------------------------------------------
>
> -------------------------
>
>> Propriétés du CPU:
>> Type de processeur Intel Pentium
>>MMX, 233 MHz
>> Alias du CPU P55C, A80503
>> CPU Stepping xB1
>> Cache de code de niveau 1 16 Ko
>> Cache de données de niveau 1 16 Ko
>> Cache de niveau 2 0
>>
>> Informations physiques sur le CPU:
>> Forme du composant 296 Pin PGA
>> Taille du composant 4.95 cm x 4.95 cm
>> Transistors 4.5 million(s)
>> Technologie utilisée 4M, 0.28 um, CMOS
>> Taille interne 140 / 128 mm2
>> Voltage au coeur 2.8 V
>> Voltage d'entrée/sortie 3.3 V
>> Puissance typique 6.1 - 7.9 W
>>(dépendant de la vitesse d'horloge)
>> Puissance maximale 13.1 - 17 W
>>(dépendant de la vitesse d'horloge)
>>
>> Fabricant du processeur:
>> Nom de l'entreprise Intel Corporation
>> Information sur le produit
>>http://www.intel.com/products/browse/processor.htm
>>
>> Utilisation du CPU:
>> CPU nº1 0 %
>>
>> Problèmes et suggestions:
>> Problème Aucun cache de
>>niveau 2 trouvé sur le CPU. Cela peut entraîner une dégradation des
>>performances.
>>
>>
>>--------[ CPUID
>>]-------------------------------------------------------------------------
>
> ------------------------------
>
>> (CPUID) Propriétés:
>> (CPUID) Fabricant GenuineIntel
>> (CPUID) Révision 0543h
>> Identifiant de la plate-forme 00h (Inconnu)
>> (IA) Numéro de série du CPU Inconnu
>>
>> Jeu d'instructions:
>> AMD 3DNow! Non géré
>> AMD 3DNow! Professional Non géré
>> AMD Enhanced 3DNow! Non géré
>> AMD Extended MMX Non géré
>> AMD64 Non géré
>> Cyrix Extended MMX Non géré
>> IA-64 Non géré
>> IA MMX Géré
>> IA SSE Non géré
>> IA SSE 2 Non géré
>> IA SSE 3 Non géré
>> Instruction CLFLUSH Non géré
>> Instruction CMPXCHG8B Géré
>> Instruction CMPXCHG16B Non géré
>> Instruction Conditional Move Non géré
>> Instruction FEMMS Non géré
>> Instruction MONITOR / MWAIT Non géré
>>
>> (CPUID) Fonctionnalités:
>> 36-bit Page Size Extension Non géré
>> Advanced Cryptography Engine Non géré
>> Alternate Instruction Set Non géré
>> Automatic Clock Control Non géré
>> CPL Qualified Debug Store Non géré
>> Debug Trace Store Non géré
>> Debugging Extension Géré
>> Enhanced SpeedStep Technology Non géré
>> Fast Save & Restore Non géré
>> Fast System Call Non géré
>> Hyper-Threading Technology Non géré
>> L1 Context ID Non géré
>> Local APIC On Chip Non géré
>> LongRun Non géré
>> LongRun Table Interface Non géré
>> Machine-Check Architecture Non géré
>> Machine-Check Exception Géré
>> Memory Type Range Registers Non géré
>> Model Specific Registers Géré
>> No-Execute Page Protection Non géré
>> Page Attribute Table Non géré
>> Page Global Extension Non géré
>> Page Size Extension Géré
>> Pending Break Event Non géré
>> Physical Address Extension Non géré
>> Processor Duty Cycle Control Non géré
>> Processor Serial Number Non géré
>> Random Number Generator Non géré
>> Self-Snoop Non géré
>> Thermal Monitor Non géré
>> Thermal Monitor 2 Non géré
>> Time Stamp Counter Géré
>> Virtual Mode Extension Géré
>>
>> Problèmes et suggestions:
>> Suggestion SSE n'est pas
>>géré sur ce système. Mettez à jour votre processeur pour tirer parti des
>>extensions SSE dans les applications qui les utilisent.
>>
>>
>>--------[ Carte mère
>>]-------------------------------------------------------------------------
>
> -------------------------
>
>> Propriétés de la carte mère:
>> Identifiant de la carte mère
>>51-0224-001437-00101111-071595-572$M572-V1.28679Release 02/24/1999 S
>> Nom de la carte mère Inconnu
>>
>>
>>--------[ Mémoire
>>]-------------------------------------------------------------------------
>
> ----------------------------
>
>> Mémoire physique:
>> Total 255 Mo
>> Utilisé 135 Mo
>> Disponible 119 Mo
>> Utilisation 53 %
>>
>> Zone de swap:
>> Total 358 Mo
>> Utilisé 80 Mo
>> Disponible 278 Mo
>> Utilisation 22 %
>>
>> Mémoire virtuelle:
>> Total 614 Mo
>> Utilisé 216 Mo
>> Disponible 398 Mo
>> Utilisation 35 %
>>
>> Problèmes et suggestions:
>> Suggestion Installez
>>davantage de mémoire système pour améliorer les performances des
>>applications.
>>
>>
>>--------[ Chipset
>>]-------------------------------------------------------------------------
>
> ----------------------------
>
>> Propriétés du chipset:
>> Chipset de la carte mère Intel Triton
>>82430TX
>> CAS Latency 3T
>> RAS To CAS Delay 3T
>> RAS Precharge 3T
>> RAS Active Time 5T
>> Taille du cache externe 512 Ko
>> Type du cache externe Dual-Bank
>>Pipelined Burst
>> État du cache externe Activé
>>
>> Slots mémoire:
>> Slot DRAM nº1 128 Mo (SDRAM)
>> Slot DRAM nº2 128 Mo (SDRAM)
>>
>> Fabricant du chipset:
>> Nom de l'entreprise Intel Corporation
>> Information sur le produit
>>http://www.intel.com/products/browse/chipsets.htm
>> Télécharger le pilote
>>http://support.intel.com/support/chipsets/index.htm
>>
>>
>>--------[ BIOS
>>]-------------------------------------------------------------------------
>
> -------------------------------
>
>> Propriétés du BIOS:
>> Type de BIOS AMI
>> Date du BIOS système 07/15/95
>> Date du BIOS vidéo 97/08/22
>>
>> Fabricant du BIOS:
>> Nom de l'entreprise American
>>Megatrends Inc.
>> Information sur le produit
>>http://www.ami.com/amibios
>>
>>
>>--------[ Vidéo Windows
>>--------------------------------------------------------------------------
>>
>> [ ATI Rage II+ PCI (ati_m64) ]
>>
>> Propriétés de la carte vidéo:
>> Description du périphérique ATI Rage II+
>>PCI (ati_m64)
>> Type de circuit Mach64: Rage II+
>> Type de DAC Interne
>> Pilotes installés ati_m64.drv
>> Taille de la mémoire 2 Mo
>>
>> Fabricant de la carte vidéo:
>> Nom de l'entreprise ATI
>>Technologies Inc.
>> Information sur le produit
>>http://www.ati.com/products/home-office.html
>> Télécharger le pilote
>>http://www.ati.com/support/driver.html
>>
>> Problèmes et suggestions:
>> Problème Il y a moins de
>>4 Mo de mémoire vidéo installés. Mettez à jour votre carte vidéo pour
>>obtenir de meilleures performances.
>>
>>
>>--------[ Vidéo PCI/AGP
>>]-------------------------------------------------------------------------
>
> ----------------------
>
>> ATI 3D-Rage II+
>> Carte vidéo
>> ATI 3D-Rage II+
>> Accélérateur 3D
>>
>>
>>--------[ Moniteur
>>]-------------------------------------------------------------------------
>
> ---------------------------
>
>> [ ViewSonic VP171b ]
>>
>> Propriétés du moniteur:
>> Nom du moniteur ViewSonic VP171b
>> Identification du moniteur VSC0C11
>> Modèle VP171b
>> Date de fabrication Semaine 6 / 2004
>> Numéro de série A1U040600116
>> Taille d'affichage maximale visible 34 cm x 27 cm
>>(17.1")
>> Ratio d'aspect de l'image 4:3
>> Fréquence horizontale 30 - 82 KHz
>> Fréquence verticale 50 - 75 Hz
>> Résolution maximale 1280 x 1024
>> Gamma 2.20
>> Gestion du mode DPMS Active-Off
>>
>> Modes vidéo gérés:
>> 640 x 480 75 Hz
>> 800 x 600 75 Hz
>> 1024 x 768 75 Hz
>> 1152 x 864 75 Hz
>> 1280 x 1024 75 Hz
>>
>> Fabricant du moniteur:
>> Nom de l'entreprise ViewSonic
>>Corporation
>> Information sur le produit
>>http://www.viewsonic.com/products/desktop_display.htm
>> Télécharger le pilote
>>http://www.viewsonic.com/support/drivers.htm
>>
>>
>
> ============================================================================
> ==
>
>>what's the video BIOS ? Is there any upgrade I could do ?
>>
>>what's the cache level 2 ?
>>
>>
>>Thanks a lot !
>>
>>Claude
>>
>>
>>
>
>
>
Anonymous
a b B Homebuilt system
December 14, 2004 9:43:26 PM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

do you mean this one :
http://members.driverguide.com/list/company796/page2/in... ??

it's for W95. May I use it yet ?

JAD a écrit:
> have you loaded the motherboard drivers for the chipset? CD that came with
> the board...
>
> "Claude" <nospam@nospam.fr> wrote in message
> news:41BF08D2.4080502@nospam.fr...
>
>>David Maynard a écrit:
>>
>>
>>>>>Unplug the machine and reset CMOS for a couple of minutes; then put
>>>>>the jumper back to normal.
>>>>>
>>>>
>>I flashed the bios with the 5720224s.rom and amifl815.exe programs. the
>>results are exactly the same, got, before, with 990224s.rom
>>
>>I also clear CMOS.
>>
>>Hereunder, you can read one part of the the Aida32 results :
>>
>>--------[ AIDA32 (c) 1995-2004 Tamas Miklos
>>]-------------------------------------------------------------------------
>
> --
>
>> Version AIDA32 v3.94.2
>> Auteur
>>tamas.miklos@aida32.hu
>> Site web
>
> http://www.aida32.hu
>
>> Type de rapport Générateur de
>>rapports Pro/Lite
>> Ordinateur ADAGIO (Pentrium
>
> II)
>
>> Générateur claude
>> Système d'exploitation Microsoft Windows
>>98 SE 4.10.2222A (Win98 SE)
>> Date 1980-01-04
>> Heure 15:29
>>
>>
>>--------[ Résumé
>>]-------------------------------------------------------------------------
>
> -----------------------------
>
>> Ordinateur:
>> Système d'exploitation Microsoft
>>Windows 98 SE
>> Service Pack du système Aucun
>> Internet Explorer 6.0.2800.1106
>>(IE 6.0 SP1)
>> Nom du système ADAGIO
>>(Pentrium II)
>> Nom d'utilisateur claude
>>
>> Carte mère:
>> Type de processeur Intel Pentium
>>MMX, 233 MHz
>> Nom de la carte mère Inconnu
>> Chipset de la carte mère Intel Triton
>>82430TX
>> Mémoire système 256 Mo (SDRAM)
>> Type de BIOS AMI (07/15/95)
>> Port de communication Port de
>>communication (COM1)
>> Port de communication Port de
>>communication (COM2)
>> Port de communication Port imprimante
>>(LPT1)
>>
>> Moniteur:
>> Carte vidéo ATI Rage II+
>>PCI (ati_m64) (2 Mo)
>> Accélérateur 3D ATI 3D-Rage II+
>> Moniteur ViewSonic
>>VP171b (A1U040600116)
>>
>> Multimédia:
>> Carte audio C-Media CMI8330
>>Audio Adapter
>>
>>
>>--------[ Processeur
>>]-------------------------------------------------------------------------
>
> -------------------------
>
>> Propriétés du CPU:
>> Type de processeur Intel Pentium
>>MMX, 233 MHz
>> Alias du CPU P55C, A80503
>> CPU Stepping xB1
>> Cache de code de niveau 1 16 Ko
>> Cache de données de niveau 1 16 Ko
>> Cache de niveau 2 0
>>
>> Informations physiques sur le CPU:
>> Forme du composant 296 Pin PGA
>> Taille du composant 4.95 cm x 4.95 cm
>> Transistors 4.5 million(s)
>> Technologie utilisée 4M, 0.28 um, CMOS
>> Taille interne 140 / 128 mm2
>> Voltage au coeur 2.8 V
>> Voltage d'entrée/sortie 3.3 V
>> Puissance typique 6.1 - 7.9 W
>>(dépendant de la vitesse d'horloge)
>> Puissance maximale 13.1 - 17 W
>>(dépendant de la vitesse d'horloge)
>>
>> Fabricant du processeur:
>> Nom de l'entreprise Intel Corporation
>> Information sur le produit
>>http://www.intel.com/products/browse/processor.htm
>>
>> Utilisation du CPU:
>> CPU nº1 0 %
>>
>> Problèmes et suggestions:
>> Problème Aucun cache de
>>niveau 2 trouvé sur le CPU. Cela peut entraîner une dégradation des
>>performances.
>>
>>
>>--------[ CPUID
>>]-------------------------------------------------------------------------
>
> ------------------------------
>
>> (CPUID) Propriétés:
>> (CPUID) Fabricant GenuineIntel
>> (CPUID) Révision 0543h
>> Identifiant de la plate-forme 00h (Inconnu)
>> (IA) Numéro de série du CPU Inconnu
>>
>> Jeu d'instructions:
>> AMD 3DNow! Non géré
>> AMD 3DNow! Professional Non géré
>> AMD Enhanced 3DNow! Non géré
>> AMD Extended MMX Non géré
>> AMD64 Non géré
>> Cyrix Extended MMX Non géré
>> IA-64 Non géré
>> IA MMX Géré
>> IA SSE Non géré
>> IA SSE 2 Non géré
>> IA SSE 3 Non géré
>> Instruction CLFLUSH Non géré
>> Instruction CMPXCHG8B Géré
>> Instruction CMPXCHG16B Non géré
>> Instruction Conditional Move Non géré
>> Instruction FEMMS Non géré
>> Instruction MONITOR / MWAIT Non géré
>>
>> (CPUID) Fonctionnalités:
>> 36-bit Page Size Extension Non géré
>> Advanced Cryptography Engine Non géré
>> Alternate Instruction Set Non géré
>> Automatic Clock Control Non géré
>> CPL Qualified Debug Store Non géré
>> Debug Trace Store Non géré
>> Debugging Extension Géré
>> Enhanced SpeedStep Technology Non géré
>> Fast Save & Restore Non géré
>> Fast System Call Non géré
>> Hyper-Threading Technology Non géré
>> L1 Context ID Non géré
>> Local APIC On Chip Non géré
>> LongRun Non géré
>> LongRun Table Interface Non géré
>> Machine-Check Architecture Non géré
>> Machine-Check Exception Géré
>> Memory Type Range Registers Non géré
>> Model Specific Registers Géré
>> No-Execute Page Protection Non géré
>> Page Attribute Table Non géré
>> Page Global Extension Non géré
>> Page Size Extension Géré
>> Pending Break Event Non géré
>> Physical Address Extension Non géré
>> Processor Duty Cycle Control Non géré
>> Processor Serial Number Non géré
>> Random Number Generator Non géré
>> Self-Snoop Non géré
>> Thermal Monitor Non géré
>> Thermal Monitor 2 Non géré
>> Time Stamp Counter Géré
>> Virtual Mode Extension Géré
>>
>> Problèmes et suggestions:
>> Suggestion SSE n'est pas
>>géré sur ce système. Mettez à jour votre processeur pour tirer parti des
>>extensions SSE dans les applications qui les utilisent.
>>
>>
>>--------[ Carte mère
>>]-------------------------------------------------------------------------
>
> -------------------------
>
>> Propriétés de la carte mère:
>> Identifiant de la carte mère
>>51-0224-001437-00101111-071595-572$M572-V1.28679Release 02/24/1999 S
>> Nom de la carte mère Inconnu
>>
>>
>>--------[ Mémoire
>>]-------------------------------------------------------------------------
>
> ----------------------------
>
>> Mémoire physique:
>> Total 255 Mo
>> Utilisé 135 Mo
>> Disponible 119 Mo
>> Utilisation 53 %
>>
>> Zone de swap:
>> Total 358 Mo
>> Utilisé 80 Mo
>> Disponible 278 Mo
>> Utilisation 22 %
>>
>> Mémoire virtuelle:
>> Total 614 Mo
>> Utilisé 216 Mo
>> Disponible 398 Mo
>> Utilisation 35 %
>>
>> Problèmes et suggestions:
>> Suggestion Installez
>>davantage de mémoire système pour améliorer les performances des
>>applications.
>>
>>
>>--------[ Chipset
>>]-------------------------------------------------------------------------
>
> ----------------------------
>
>> Propriétés du chipset:
>> Chipset de la carte mère Intel Triton
>>82430TX
>> CAS Latency 3T
>> RAS To CAS Delay 3T
>> RAS Precharge 3T
>> RAS Active Time 5T
>> Taille du cache externe 512 Ko
>> Type du cache externe Dual-Bank
>>Pipelined Burst
>> État du cache externe Activé
>>
>> Slots mémoire:
>> Slot DRAM nº1 128 Mo (SDRAM)
>> Slot DRAM nº2 128 Mo (SDRAM)
>>
>> Fabricant du chipset:
>> Nom de l'entreprise Intel Corporation
>> Information sur le produit
>>http://www.intel.com/products/browse/chipsets.htm
>> Télécharger le pilote
>>http://support.intel.com/support/chipsets/index.htm
>>
>>
>>--------[ BIOS
>>]-------------------------------------------------------------------------
>
> -------------------------------
>
>> Propriétés du BIOS:
>> Type de BIOS AMI
>> Date du BIOS système 07/15/95
>> Date du BIOS vidéo 97/08/22
>>
>> Fabricant du BIOS:
>> Nom de l'entreprise American
>>Megatrends Inc.
>> Information sur le produit
>>http://www.ami.com/amibios
>>
>>
>>--------[ Vidéo Windows
>>--------------------------------------------------------------------------
>>
>> [ ATI Rage II+ PCI (ati_m64) ]
>>
>> Propriétés de la carte vidéo:
>> Description du périphérique ATI Rage II+
>>PCI (ati_m64)
>> Type de circuit Mach64: Rage II+
>> Type de DAC Interne
>> Pilotes installés ati_m64.drv
>> Taille de la mémoire 2 Mo
>>
>> Fabricant de la carte vidéo:
>> Nom de l'entreprise ATI
>>Technologies Inc.
>> Information sur le produit
>>http://www.ati.com/products/home-office.html
>> Télécharger le pilote
>>http://www.ati.com/support/driver.html
>>
>> Problèmes et suggestions:
>> Problème Il y a moins de
>>4 Mo de mémoire vidéo installés. Mettez à jour votre carte vidéo pour
>>obtenir de meilleures performances.
>>
>>
>>--------[ Vidéo PCI/AGP
>>]-------------------------------------------------------------------------
>
> ----------------------
>
>> ATI 3D-Rage II+
>> Carte vidéo
>> ATI 3D-Rage II+
>> Accélérateur 3D
>>
>>
>>--------[ Moniteur
>>]-------------------------------------------------------------------------
>
> ---------------------------
>
>> [ ViewSonic VP171b ]
>>
>> Propriétés du moniteur:
>> Nom du moniteur ViewSonic VP171b
>> Identification du moniteur VSC0C11
>> Modèle VP171b
>> Date de fabrication Semaine 6 / 2004
>> Numéro de série A1U040600116
>> Taille d'affichage maximale visible 34 cm x 27 cm
>>(17.1")
>> Ratio d'aspect de l'image 4:3
>> Fréquence horizontale 30 - 82 KHz
>> Fréquence verticale 50 - 75 Hz
>> Résolution maximale 1280 x 1024
>> Gamma 2.20
>> Gestion du mode DPMS Active-Off
>>
>> Modes vidéo gérés:
>> 640 x 480 75 Hz
>> 800 x 600 75 Hz
>> 1024 x 768 75 Hz
>> 1152 x 864 75 Hz
>> 1280 x 1024 75 Hz
>>
>> Fabricant du moniteur:
>> Nom de l'entreprise ViewSonic
>>Corporation
>> Information sur le produit
>>http://www.viewsonic.com/products/desktop_display.htm
>> Télécharger le pilote
>>http://www.viewsonic.com/support/drivers.htm
>>
>>
>
> ============================================================================
> ==
>
>>what's the video BIOS ? Is there any upgrade I could do ?
>>
>>what's the cache level 2 ?
>>
>>
>>Thanks a lot !
>>
>>Claude
>>
>>
>>
>
>
>
Anonymous
a b B Homebuilt system
December 15, 2004 4:42:35 AM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

Claude wrote:
> I never had any CD for my mobo. my PC is not a brand like HP, Compaq ...
> where can I find those drivers ?
>

The motherboard or chipset manufacturer's website...

> thx
> Claude
>
> JAD a écrit:
>
>> have you loaded the motherboard drivers for the chipset? CD that came
>> with
>> the board...
>>
>> "Claude" <nospam@nospam.fr> wrote in message
>> news:41BF08D2.4080502@nospam.fr...
>>
>>> David Maynard a écrit:
>>>
>>>
>>>>>> Unplug the machine and reset CMOS for a couple of minutes; then put
>>>>>> the jumper back to normal.
>>>>>>
>>>>>
>>> I flashed the bios with the 5720224s.rom and amifl815.exe programs. the
>>> results are exactly the same, got, before, with 990224s.rom
>>>
>>> I also clear CMOS.
>>>
>>> Hereunder, you can read one part of the the Aida32 results :
>>>
>>> --------[ AIDA32 (c) 1995-2004 Tamas Miklos
>>> ]-------------------------------------------------------------------------
>>>
>>
>>
>> --
>>
>>> Version AIDA32 v3.94.2
>>> Auteur
>>> tamas.miklos@aida32.hu
>>> Site web
>>
>>
>> http://www.aida32.hu
>>
>>> Type de rapport Générateur de
>>> rapports Pro/Lite
>>> Ordinateur ADAGIO (Pentrium
>>
>>
>> II)
>>
>>> Générateur claude
>>> Système d'exploitation Microsoft Windows
>>> 98 SE 4.10.2222A (Win98 SE)
>>> Date 1980-01-04
>>> Heure 15:29
>>>
>>>
>>> --------[ Résumé
>>> ]-------------------------------------------------------------------------
>>>
>>
>>
>> -----------------------------
>>
>>> Ordinateur:
>>> Système d'exploitation Microsoft
>>> Windows 98 SE
>>> Service Pack du système Aucun
>>> Internet Explorer 6.0.2800.1106
>>> (IE 6.0 SP1)
>>> Nom du système ADAGIO
>>> (Pentrium II)
>>> Nom d'utilisateur claude
>>>
>>> Carte mère:
>>> Type de processeur Intel Pentium
>>> MMX, 233 MHz
>>> Nom de la carte mère Inconnu
>>> Chipset de la carte mère Intel Triton
>>> 82430TX
>>> Mémoire système 256 Mo (SDRAM)
>>> Type de BIOS AMI (07/15/95)
>>> Port de communication Port de
>>> communication (COM1)
>>> Port de communication Port de
>>> communication (COM2)
>>> Port de communication Port imprimante
>>> (LPT1)
>>>
>>> Moniteur:
>>> Carte vidéo ATI Rage II+
>>> PCI (ati_m64) (2 Mo)
>>> Accélérateur 3D ATI 3D-Rage II+
>>> Moniteur ViewSonic
>>> VP171b (A1U040600116)
>>>
>>> Multimédia:
>>> Carte audio C-Media CMI8330
>>> Audio Adapter
>>>
>>>
>>> --------[ Processeur
>>> ]-------------------------------------------------------------------------
>>>
>>
>>
>> -------------------------
>>
>>> Propriétés du CPU:
>>> Type de processeur Intel Pentium
>>> MMX, 233 MHz
>>> Alias du CPU P55C, A80503
>>> CPU Stepping xB1
>>> Cache de code de niveau 1 16 Ko
>>> Cache de données de niveau 1 16 Ko
>>> Cache de niveau 2 0
>>>
>>> Informations physiques sur le CPU:
>>> Forme du composant 296 Pin PGA
>>> Taille du composant 4.95 cm x
>>> 4.95 cm
>>> Transistors 4.5 million(s)
>>> Technologie utilisée 4M, 0.28 um,
>>> CMOS
>>> Taille interne 140 / 128 mm2
>>> Voltage au coeur 2.8 V
>>> Voltage d'entrée/sortie 3.3 V
>>> Puissance typique 6.1 - 7.9 W
>>> (dépendant de la vitesse d'horloge)
>>> Puissance maximale 13.1 - 17 W
>>> (dépendant de la vitesse d'horloge)
>>>
>>> Fabricant du processeur:
>>> Nom de l'entreprise Intel
>>> Corporation
>>> Information sur le produit
>>> http://www.intel.com/products/browse/processor.htm
>>>
>>> Utilisation du CPU:
>>> CPU nº1 0 %
>>>
>>> Problèmes et suggestions:
>>> Problème Aucun cache de
>>> niveau 2 trouvé sur le CPU. Cela peut entraîner une dégradation des
>>> performances.
>>>
>>>
>>> --------[ CPUID
>>> ]-------------------------------------------------------------------------
>>>
>>
>>
>> ------------------------------
>>
>>> (CPUID) Propriétés:
>>> (CPUID) Fabricant GenuineIntel
>>> (CPUID) Révision 0543h
>>> Identifiant de la plate-forme 00h (Inconnu)
>>> (IA) Numéro de série du CPU Inconnu
>>>
>>> Jeu d'instructions:
>>> AMD 3DNow! Non géré
>>> AMD 3DNow! Professional Non géré
>>> AMD Enhanced 3DNow! Non géré
>>> AMD Extended MMX Non géré
>>> AMD64 Non géré
>>> Cyrix Extended MMX Non géré
>>> IA-64 Non géré
>>> IA MMX Géré
>>> IA SSE Non géré
>>> IA SSE 2 Non géré
>>> IA SSE 3 Non géré
>>> Instruction CLFLUSH Non géré
>>> Instruction CMPXCHG8B Géré
>>> Instruction CMPXCHG16B Non géré
>>> Instruction Conditional Move Non géré
>>> Instruction FEMMS Non géré
>>> Instruction MONITOR / MWAIT Non géré
>>>
>>> (CPUID) Fonctionnalités:
>>> 36-bit Page Size Extension Non géré
>>> Advanced Cryptography Engine Non géré
>>> Alternate Instruction Set Non géré
>>> Automatic Clock Control Non géré
>>> CPL Qualified Debug Store Non géré
>>> Debug Trace Store Non géré
>>> Debugging Extension Géré
>>> Enhanced SpeedStep Technology Non géré
>>> Fast Save & Restore Non géré
>>> Fast System Call Non géré
>>> Hyper-Threading Technology Non géré
>>> L1 Context ID Non géré
>>> Local APIC On Chip Non géré
>>> LongRun Non géré
>>> LongRun Table Interface Non géré
>>> Machine-Check Architecture Non géré
>>> Machine-Check Exception Géré
>>> Memory Type Range Registers Non géré
>>> Model Specific Registers Géré
>>> No-Execute Page Protection Non géré
>>> Page Attribute Table Non géré
>>> Page Global Extension Non géré
>>> Page Size Extension Géré
>>> Pending Break Event Non géré
>>> Physical Address Extension Non géré
>>> Processor Duty Cycle Control Non géré
>>> Processor Serial Number Non géré
>>> Random Number Generator Non géré
>>> Self-Snoop Non géré
>>> Thermal Monitor Non géré
>>> Thermal Monitor 2 Non géré
>>> Time Stamp Counter Géré
>>> Virtual Mode Extension Géré
>>>
>>> Problèmes et suggestions:
>>> Suggestion SSE n'est pas
>>> géré sur ce système. Mettez à jour votre processeur pour tirer parti des
>>> extensions SSE dans les applications qui les utilisent.
>>>
>>>
>>> --------[ Carte mère
>>> ]-------------------------------------------------------------------------
>>>
>>
>>
>> -------------------------
>>
>>> Propriétés de la carte mère:
>>> Identifiant de la carte mère
>>> 51-0224-001437-00101111-071595-572$M572-V1.28679Release 02/24/1999 S
>>> Nom de la carte mère Inconnu
>>>
>>>
>>> --------[ Mémoire
>>> ]-------------------------------------------------------------------------
>>>
>>
>>
>> ----------------------------
>>
>>> Mémoire physique:
>>> Total 255 Mo
>>> Utilisé 135 Mo
>>> Disponible 119 Mo
>>> Utilisation 53 %
>>>
>>> Zone de swap:
>>> Total 358 Mo
>>> Utilisé 80 Mo
>>> Disponible 278 Mo
>>> Utilisation 22 %
>>>
>>> Mémoire virtuelle:
>>> Total 614 Mo
>>> Utilisé 216 Mo
>>> Disponible 398 Mo
>>> Utilisation 35 %
>>>
>>> Problèmes et suggestions:
>>> Suggestion Installez
>>> davantage de mémoire système pour améliorer les performances des
>>> applications.
>>>
>>>
>>> --------[ Chipset
>>> ]-------------------------------------------------------------------------
>>>
>>
>>
>> ----------------------------
>>
>>> Propriétés du chipset:
>>> Chipset de la carte mère Intel Triton
>>> 82430TX
>>> CAS Latency 3T
>>> RAS To CAS Delay 3T
>>> RAS Precharge 3T
>>> RAS Active Time 5T
>>> Taille du cache externe 512 Ko
>>> Type du cache externe Dual-Bank
>>> Pipelined Burst
>>> État du cache externe Activé
>>>
>>> Slots mémoire:
>>> Slot DRAM nº1 128 Mo (SDRAM)
>>> Slot DRAM nº2 128 Mo (SDRAM)
>>>
>>> Fabricant du chipset:
>>> Nom de l'entreprise Intel
>>> Corporation
>>> Information sur le produit
>>> http://www.intel.com/products/browse/chipsets.htm
>>> Télécharger le pilote
>>> http://support.intel.com/support/chipsets/index.htm
>>>
>>>
>>> --------[ BIOS
>>> ]-------------------------------------------------------------------------
>>>
>>
>>
>> -------------------------------
>>
>>> Propriétés du BIOS:
>>> Type de BIOS AMI
>>> Date du BIOS système 07/15/95
>>> Date du BIOS vidéo 97/08/22
>>>
>>> Fabricant du BIOS:
>>> Nom de l'entreprise American
>>> Megatrends Inc.
>>> Information sur le produit
>>> http://www.ami.com/amibios
>>>
>>>
>>> --------[ Vidéo Windows
>>> --------------------------------------------------------------------------
>>>
>>>
>>> [ ATI Rage II+ PCI (ati_m64) ]
>>>
>>> Propriétés de la carte vidéo:
>>> Description du périphérique ATI Rage II+
>>> PCI (ati_m64)
>>> Type de circuit Mach64: Rage II+
>>> Type de DAC Interne
>>> Pilotes installés ati_m64.drv
>>> Taille de la mémoire 2 Mo
>>>
>>> Fabricant de la carte vidéo:
>>> Nom de l'entreprise ATI
>>> Technologies Inc.
>>> Information sur le produit
>>> http://www.ati.com/products/home-office.html
>>> Télécharger le pilote
>>> http://www.ati.com/support/driver.html
>>>
>>> Problèmes et suggestions:
>>> Problème Il y a moins de
>>> 4 Mo de mémoire vidéo installés. Mettez à jour votre carte vidéo pour
>>> obtenir de meilleures performances.
>>>
>>>
>>> --------[ Vidéo PCI/AGP
>>> ]-------------------------------------------------------------------------
>>>
>>
>>
>> ----------------------
>>
>>> ATI 3D-Rage II+
>>> Carte vidéo
>>> ATI 3D-Rage II+
>>> Accélérateur 3D
>>>
>>>
>>> --------[ Moniteur
>>> ]-------------------------------------------------------------------------
>>>
>>
>>
>> ---------------------------
>>
>>> [ ViewSonic VP171b ]
>>>
>>> Propriétés du moniteur:
>>> Nom du moniteur ViewSonic VP171b
>>> Identification du moniteur VSC0C11
>>> Modèle VP171b
>>> Date de fabrication Semaine 6 / 2004
>>> Numéro de série A1U040600116
>>> Taille d'affichage maximale visible 34 cm x 27 cm
>>> (17.1")
>>> Ratio d'aspect de l'image 4:3
>>> Fréquence horizontale 30 - 82 KHz
>>> Fréquence verticale 50 - 75 Hz
>>> Résolution maximale 1280 x 1024
>>> Gamma 2.20
>>> Gestion du mode DPMS Active-Off
>>>
>>> Modes vidéo gérés:
>>> 640 x 480 75 Hz
>>> 800 x 600 75 Hz
>>> 1024 x 768 75 Hz
>>> 1152 x 864 75 Hz
>>> 1280 x 1024 75 Hz
>>>
>>> Fabricant du moniteur:
>>> Nom de l'entreprise ViewSonic
>>> Corporation
>>> Information sur le produit
>>> http://www.viewsonic.com/products/desktop_display.htm
>>> Télécharger le pilote
>>> http://www.viewsonic.com/support/drivers.htm
>>>
>>>
>>
>> ============================================================================
>>
>> ==
>>
>>> what's the video BIOS ? Is there any upgrade I could do ?
>>>
>>> what's the cache level 2 ?
>>>
>>>
>>> Thanks a lot !
>>>
>>> Claude
>>>
>>>
>>>
>>
>>
>>
>


--
spammage trappage: replace fishies_ with yahoo

I'm going to die rather sooner than I'd like. I tried to protect my
neighbours from crime, and became the victim of it. To jump to the end
of the story, as a result of this I need a bone marrow transplant. Many
people around the world are waiting for a marrow transplant, too. Please
volunteer to be a marrow donor:
http://www.abmdr.org.au/
http://www.marrow.org/
Anonymous
a b B Homebuilt system
December 15, 2004 4:42:36 AM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

PCChips company is like its products : not serious.
no driver can be found there (http://www.pcchips.com.tw) for such an old
PII (socket 7) !!

spodosaurus a écrit:
> Claude wrote:
>
>> I never had any CD for my mobo. my PC is not a brand like HP, Compaq ...
>> where can I find those drivers ?
>>
>
> The motherboard or chipset manufacturer's website...
>
>> thx
>> Claude
>>
>> JAD a écrit:
>>
>>> have you loaded the motherboard drivers for the chipset? CD that
>>> came with
>>> the board...
>>>
>>> "Claude" <nospam@nospam.fr> wrote in message
>>> news:41BF08D2.4080502@nospam.fr...
>>>
>>>> David Maynard a écrit:
>>>>
>>>>
>>>>>>> Unplug the machine and reset CMOS for a couple of minutes; then put
>>>>>>> the jumper back to normal.
>>>>>>>
>>>>>>
>>>> I flashed the bios with the 5720224s.rom and amifl815.exe programs. the
>>>> results are exactly the same, got, before, with 990224s.rom
>>>>
>>>> I also clear CMOS.
>>>>
>>>> Hereunder, you can read one part of the the Aida32 results :
>>>>
>>>> --------[ AIDA32 (c) 1995-2004 Tamas Miklos
>>>> ]-------------------------------------------------------------------------
>>>>
>>>
>>>
>>>
>>> --
>>>
>>>> Version AIDA32 v3.94.2
>>>> Auteur
>>>> tamas.miklos@aida32.hu
>>>> Site web
>>>
>>>
>>>
>>> http://www.aida32.hu
>>>
>>>> Type de rapport Générateur de
>>>> rapports Pro/Lite
>>>> Ordinateur ADAGIO (Pentrium
>>>
>>>
>>>
>>> II)
>>>
>>>> Générateur claude
>>>> Système d'exploitation Microsoft Windows
>>>> 98 SE 4.10.2222A (Win98 SE)
>>>> Date 1980-01-04
>>>> Heure 15:29
>>>>
>>>>
>>>> --------[ Résumé
>>>> ]-------------------------------------------------------------------------
>>>>
>>>
>>>
>>>
>>> -----------------------------
>>>
>>>> Ordinateur:
>>>> Système d'exploitation Microsoft
>>>> Windows 98 SE
>>>> Service Pack du système Aucun
>>>> Internet Explorer 6.0.2800.1106
>>>> (IE 6.0 SP1)
>>>> Nom du système ADAGIO
>>>> (Pentrium II)
>>>> Nom d'utilisateur claude
>>>>
>>>> Carte mère:
>>>> Type de processeur Intel Pentium
>>>> MMX, 233 MHz
>>>> Nom de la carte mère Inconnu
>>>> Chipset de la carte mère Intel Triton
>>>> 82430TX
>>>> Mémoire système 256 Mo (SDRAM)
>>>> Type de BIOS AMI (07/15/95)
>>>> Port de communication Port de
>>>> communication (COM1)
>>>> Port de communication Port de
>>>> communication (COM2)
>>>> Port de communication Port imprimante
>>>> (LPT1)
>>>>
>>>> Moniteur:
>>>> Carte vidéo ATI Rage II+
>>>> PCI (ati_m64) (2 Mo)
>>>> Accélérateur 3D ATI 3D-Rage II+
>>>> Moniteur ViewSonic
>>>> VP171b (A1U040600116)
>>>>
>>>> Multimédia:
>>>> Carte audio C-Media CMI8330
>>>> Audio Adapter
>>>>
>>>>
>>>> --------[ Processeur
>>>> ]-------------------------------------------------------------------------
>>>>
>>>
>>>
>>>
>>> -------------------------
>>>
>>>> Propriétés du CPU:
>>>> Type de processeur Intel Pentium
>>>> MMX, 233 MHz
>>>> Alias du CPU P55C, A80503
>>>> CPU Stepping xB1
>>>> Cache de code de niveau 1 16 Ko
>>>> Cache de données de niveau 1 16 Ko
>>>> Cache de niveau 2 0
>>>>
>>>> Informations physiques sur le CPU:
>>>> Forme du composant 296 Pin PGA
>>>> Taille du composant 4.95 cm x
>>>> 4.95 cm
>>>> Transistors 4.5 million(s)
>>>> Technologie utilisée 4M, 0.28 um,
>>>> CMOS
>>>> Taille interne 140 / 128 mm2
>>>> Voltage au coeur 2.8 V
>>>> Voltage d'entrée/sortie 3.3 V
>>>> Puissance typique 6.1 - 7.9 W
>>>> (dépendant de la vitesse d'horloge)
>>>> Puissance maximale 13.1 - 17 W
>>>> (dépendant de la vitesse d'horloge)
>>>>
>>>> Fabricant du processeur:
>>>> Nom de l'entreprise Intel
>>>> Corporation
>>>> Information sur le produit
>>>> http://www.intel.com/products/browse/processor.htm
>>>>
>>>> Utilisation du CPU:
>>>> CPU nº1 0 %
>>>>
>>>> Problèmes et suggestions:
>>>> Problème Aucun cache de
>>>> niveau 2 trouvé sur le CPU. Cela peut entraîner une dégradation des
>>>> performances.
>>>>
>>>>
>>>> --------[ CPUID
>>>> ]-------------------------------------------------------------------------
>>>>
>>>
>>>
>>>
>>> ------------------------------
>>>
>>>> (CPUID) Propriétés:
>>>> (CPUID) Fabricant GenuineIntel
>>>> (CPUID) Révision 0543h
>>>> Identifiant de la plate-forme 00h (Inconnu)
>>>> (IA) Numéro de série du CPU Inconnu
>>>>
>>>> Jeu d'instructions:
>>>> AMD 3DNow! Non géré
>>>> AMD 3DNow! Professional Non géré
>>>> AMD Enhanced 3DNow! Non géré
>>>> AMD Extended MMX Non géré
>>>> AMD64 Non géré
>>>> Cyrix Extended MMX Non géré
>>>> IA-64 Non géré
>>>> IA MMX Géré
>>>> IA SSE Non géré
>>>> IA SSE 2 Non géré
>>>> IA SSE 3 Non géré
>>>> Instruction CLFLUSH Non géré
>>>> Instruction CMPXCHG8B Géré
>>>> Instruction CMPXCHG16B Non géré
>>>> Instruction Conditional Move Non géré
>>>> Instruction FEMMS Non géré
>>>> Instruction MONITOR / MWAIT Non géré
>>>>
>>>> (CPUID) Fonctionnalités:
>>>> 36-bit Page Size Extension Non géré
>>>> Advanced Cryptography Engine Non géré
>>>> Alternate Instruction Set Non géré
>>>> Automatic Clock Control Non géré
>>>> CPL Qualified Debug Store Non géré
>>>> Debug Trace Store Non géré
>>>> Debugging Extension Géré
>>>> Enhanced SpeedStep Technology Non géré
>>>> Fast Save & Restore Non géré
>>>> Fast System Call Non géré
>>>> Hyper-Threading Technology Non géré
>>>> L1 Context ID Non géré
>>>> Local APIC On Chip Non géré
>>>> LongRun Non géré
>>>> LongRun Table Interface Non géré
>>>> Machine-Check Architecture Non géré
>>>> Machine-Check Exception Géré
>>>> Memory Type Range Registers Non géré
>>>> Model Specific Registers Géré
>>>> No-Execute Page Protection Non géré
>>>> Page Attribute Table Non géré
>>>> Page Global Extension Non géré
>>>> Page Size Extension Géré
>>>> Pending Break Event Non géré
>>>> Physical Address Extension Non géré
>>>> Processor Duty Cycle Control Non géré
>>>> Processor Serial Number Non géré
>>>> Random Number Generator Non géré
>>>> Self-Snoop Non géré
>>>> Thermal Monitor Non géré
>>>> Thermal Monitor 2 Non géré
>>>> Time Stamp Counter Géré
>>>> Virtual Mode Extension Géré
>>>>
>>>> Problèmes et suggestions:
>>>> Suggestion SSE n'est pas
>>>> géré sur ce système. Mettez à jour votre processeur pour tirer parti
>>>> des
>>>> extensions SSE dans les applications qui les utilisent.
>>>>
>>>>
>>>> --------[ Carte mère
>>>> ]-------------------------------------------------------------------------
>>>>
>>>
>>>
>>>
>>> -------------------------
>>>
>>>> Propriétés de la carte mère:
>>>> Identifiant de la carte mère
>>>> 51-0224-001437-00101111-071595-572$M572-V1.28679Release 02/24/1999 S
>>>> Nom de la carte mère Inconnu
>>>>
>>>>
>>>> --------[ Mémoire
>>>> ]-------------------------------------------------------------------------
>>>>
>>>
>>>
>>>
>>> ----------------------------
>>>
>>>> Mémoire physique:
>>>> Total 255 Mo
>>>> Utilisé 135 Mo
>>>> Disponible 119 Mo
>>>> Utilisation 53 %
>>>>
>>>> Zone de swap:
>>>> Total 358 Mo
>>>> Utilisé 80 Mo
>>>> Disponible 278 Mo
>>>> Utilisation 22 %
>>>>
>>>> Mémoire virtuelle:
>>>> Total 614 Mo
>>>> Utilisé 216 Mo
>>>> Disponible 398 Mo
>>>> Utilisation 35 %
>>>>
>>>> Problèmes et suggestions:
>>>> Suggestion Installez
>>>> davantage de mémoire système pour améliorer les performances des
>>>> applications.
>>>>
>>>>
>>>> --------[ Chipset
>>>> ]-------------------------------------------------------------------------
>>>>
>>>
>>>
>>>
>>> ----------------------------
>>>
>>>> Propriétés du chipset:
>>>> Chipset de la carte mère Intel Triton
>>>> 82430TX
>>>> CAS Latency 3T
>>>> RAS To CAS Delay 3T
>>>> RAS Precharge 3T
>>>> RAS Active Time 5T
>>>> Taille du cache externe 512 Ko
>>>> Type du cache externe Dual-Bank
>>>> Pipelined Burst
>>>> État du cache externe Activé
>>>>
>>>> Slots mémoire:
>>>> Slot DRAM nº1 128 Mo (SDRAM)
>>>> Slot DRAM nº2 128 Mo (SDRAM)
>>>>
>>>> Fabricant du chipset:
>>>> Nom de l'entreprise Intel
>>>> Corporation
>>>> Information sur le produit
>>>> http://www.intel.com/products/browse/chipsets.htm
>>>> Télécharger le pilote
>>>> http://support.intel.com/support/chipsets/index.htm
>>>>
>>>>
>>>> --------[ BIOS
>>>> ]-------------------------------------------------------------------------
>>>>
>>>
>>>
>>>
>>> -------------------------------
>>>
>>>> Propriétés du BIOS:
>>>> Type de BIOS AMI
>>>> Date du BIOS système 07/15/95
>>>> Date du BIOS vidéo 97/08/22
>>>>
>>>> Fabricant du BIOS:
>>>> Nom de l'entreprise American
>>>> Megatrends Inc.
>>>> Information sur le produit
>>>> http://www.ami.com/amibios
>>>>
>>>>
>>>> --------[ Vidéo Windows
>>>> --------------------------------------------------------------------------
>>>>
>>>>
>>>> [ ATI Rage II+ PCI (ati_m64) ]
>>>>
>>>> Propriétés de la carte vidéo:
>>>> Description du périphérique ATI Rage II+
>>>> PCI (ati_m64)
>>>> Type de circuit Mach64: Rage
>>>> II+
>>>> Type de DAC Interne
>>>> Pilotes installés ati_m64.drv
>>>> Taille de la mémoire 2 Mo
>>>>
>>>> Fabricant de la carte vidéo:
>>>> Nom de l'entreprise ATI
>>>> Technologies Inc.
>>>> Information sur le produit
>>>> http://www.ati.com/products/home-office.html
>>>> Télécharger le pilote
>>>> http://www.ati.com/support/driver.html
>>>>
>>>> Problèmes et suggestions:
>>>> Problème Il y a moins de
>>>> 4 Mo de mémoire vidéo installés. Mettez à jour votre carte vidéo pour
>>>> obtenir de meilleures performances.
>>>>
>>>>
>>>> --------[ Vidéo PCI/AGP
>>>> ]-------------------------------------------------------------------------
>>>>
>>>
>>>
>>>
>>> ----------------------
>>>
>>>> ATI 3D-Rage II+
>>>> Carte vidéo
>>>> ATI 3D-Rage II+
>>>> Accélérateur 3D
>>>>
>>>>
>>>> --------[ Moniteur
>>>> ]-------------------------------------------------------------------------
>>>>
>>>
>>>
>>>
>>> ---------------------------
>>>
>>>> [ ViewSonic VP171b ]
>>>>
>>>> Propriétés du moniteur:
>>>> Nom du moniteur ViewSonic
>>>> VP171b
>>>> Identification du moniteur VSC0C11
>>>> Modèle VP171b
>>>> Date de fabrication Semaine 6 /
>>>> 2004
>>>> Numéro de série A1U040600116
>>>> Taille d'affichage maximale visible 34 cm x 27 cm
>>>> (17.1")
>>>> Ratio d'aspect de l'image 4:3
>>>> Fréquence horizontale 30 - 82 KHz
>>>> Fréquence verticale 50 - 75 Hz
>>>> Résolution maximale 1280 x 1024
>>>> Gamma 2.20
>>>> Gestion du mode DPMS Active-Off
>>>>
>>>> Modes vidéo gérés:
>>>> 640 x 480 75 Hz
>>>> 800 x 600 75 Hz
>>>> 1024 x 768 75 Hz
>>>> 1152 x 864 75 Hz
>>>> 1280 x 1024 75 Hz
>>>>
>>>> Fabricant du moniteur:
>>>> Nom de l'entreprise ViewSonic
>>>> Corporation
>>>> Information sur le produit
>>>> http://www.viewsonic.com/products/desktop_display.htm
>>>> Télécharger le pilote
>>>> http://www.viewsonic.com/support/drivers.htm
>>>>
>>>>
>>>
>>> ============================================================================
>>>
>>> ==
>>>
>>>> what's the video BIOS ? Is there any upgrade I could do ?
>>>>
>>>> what's the cache level 2 ?
>>>>
>>>>
>>>> Thanks a lot !
>>>>
>>>> Claude
>>>>
>>>>
>>>>
>>>
>>>
>>>
>>
>
>
Anonymous
a b B Homebuilt system
December 16, 2004 5:31:16 AM

Archived from groups: alt.comp.hardware.pc-homebuilt (More info?)

Claude wrote:

> David Maynard a écrit:
>
>>
>>>
>>>>
>>>> Unplug the machine and reset CMOS for a couple of minutes; then put
>>>> the jumper back to normal.
>>>>
>
> I flashed the bios with the 5720224s.rom and amifl815.exe programs. the
> results are exactly the same, got, before, with 990224s.rom
>
> I also clear CMOS.
>
> Hereunder, you can read one part of the the Aida32 results :
>
> --------[ AIDA32 (c) 1995-2004 Tamas Miklos
> ]---------------------------------------------------------------------------
>
>
> Version AIDA32 v3.94.2
> Auteur tamas.miklos@aida32.hu
> Site web http://www.aida32.hu
> Type de rapport Générateur de
> rapports Pro/Lite
> Ordinateur ADAGIO (Pentrium II)
> Générateur claude
> Système d'exploitation Microsoft Windows
> 98 SE 4.10.2222A (Win98 SE)
> Date 1980-01-04
> Heure 15:29
>
>
> --------[ Résumé
> ]------------------------------------------------------------------------------------------------------
>
>
> Ordinateur:
> Système d'exploitation Microsoft
> Windows 98 SE
> Service Pack du système Aucun
> Internet Explorer 6.0.2800.1106
> (IE 6.0 SP1)
> Nom du système ADAGIO (Pentrium
> II)
> Nom d'utilisateur claude
>
> Carte mère:
> Type de processeur Intel Pentium
> MMX, 233 MHz
> Nom de la carte mère Inconnu
> Chipset de la carte mère Intel Triton
> 82430TX
> Mémoire système 256 Mo (SDRAM)
> Type de BIOS AMI (07/15/95)
> Port de communication Port de
> communication (COM1)
> Port de communication Port de
> communication (COM2)
> Port de communication Port imprimante
> (LPT1)
>
> Moniteur:
> Carte vidéo ATI Rage II+ PCI
> (ati_m64) (2 Mo)
> Accélérateur 3D ATI 3D-Rage II+
> Moniteur ViewSonic
> VP171b (A1U040600116)
>
> Multimédia:
> Carte audio C-Media CMI8330
> Audio Adapter
>
>
> --------[ Processeur
> ]--------------------------------------------------------------------------------------------------
>
>
> Propriétés du CPU:
> Type de processeur Intel Pentium
> MMX, 233 MHz
> Alias du CPU P55C, A80503
> CPU Stepping xB1
> Cache de code de niveau 1 16 Ko
> Cache de données de niveau 1 16 Ko
> Cache de niveau 2 0
>
> Informations physiques sur le CPU:
> Forme du composant 296 Pin PGA
> Taille du composant 4.95 cm x 4.95 cm
> Transistors 4.5 million(s)
> Technologie utilisée 4M, 0.28 um, CMOS
> Taille interne 140 / 128 mm2
> Voltage au coeur 2.8 V
> Voltage d'entrée/sortie 3.3 V
> Puissance typique 6.1 - 7.9 W
> (dépendant de la vitesse d'horloge)
> Puissance maximale 13.1 - 17 W
> (dépendant de la vitesse d'horloge)
>
> Fabricant du processeur:
> Nom de l'entreprise Intel Corporation
> Information sur le produit
> http://www.intel.com/products/browse/processor.htm
>
> Utilisation du CPU:
> CPU nº1 0 %
>
> Problèmes et suggestions:
> Problème Aucun cache de
> niveau 2 trouvé sur le CPU. Cela peut entraîner une dégradation des
> performances.
>
>
> --------[ CPUID
> ]-------------------------------------------------------------------------------------------------------
>
>
> (CPUID) Propriétés:
> (CPUID) Fabricant GenuineIntel
> (CPUID) Révision 0543h
> Identifiant de la plate-forme 00h (Inconnu)
> (IA) Numéro de série du CPU Inconnu
>
> Jeu d'instructions:
> AMD 3DNow! Non géré
> AMD 3DNow! Professional Non géré
> AMD Enhanced 3DNow! Non géré
> AMD Extended MMX Non géré
> AMD64 Non géré
> Cyrix Extended MMX Non géré
> IA-64 Non géré
> IA MMX Géré
> IA SSE Non géré
> IA SSE 2 Non géré
> IA SSE 3 Non géré
> Instruction CLFLUSH Non géré
> Instruction CMPXCHG8B Géré
> Instruction CMPXCHG16B Non géré
> Instruction Conditional Move Non géré
> Instruction FEMMS Non géré
> Instruction MONITOR / MWAIT Non géré
>
> (CPUID) Fonctionnalités:
> 36-bit Page Size Extension Non géré
> Advanced Cryptography Engine Non géré
> Alternate Instruction Set Non géré
> Automatic Clock Control Non géré
> CPL Qualified Debug Store Non géré
> Debug Trace Store Non géré
> Debugging Extension Géré
> Enhanced SpeedStep Technology Non géré
> Fast Save & Restore Non géré
> Fast System Call Non géré
> Hyper-Threading Technology Non géré
> L1 Context ID Non géré
> Local APIC On Chip Non géré
> LongRun Non géré
> LongRun Table Interface Non géré
> Machine-Check Architecture Non géré
> Machine-Check Exception Géré
> Memory Type Range Registers Non géré
> Model Specific Registers Géré
> No-Execute Page Protection Non géré
> Page Attribute Table Non géré
> Page Global Extension Non géré
> Page Size Extension Géré
> Pending Break Event Non géré
> Physical Address Extension Non géré
> Processor Duty Cycle Control Non géré
> Processor Serial Number Non géré
> Random Number Generator Non géré
> Self-Snoop Non géré
> Thermal Monitor Non géré
> Thermal Monitor 2 Non géré
> Time Stamp Counter Géré
> Virtual Mode Extension Géré
>
> Problèmes et suggestions:
> Suggestion SSE n'est pas
> géré sur ce système. Mettez à jour votre processeur pour tirer parti des
> extensions SSE dans les applications qui les utilisent.
>
>
> --------[ Carte mère
> ]--------------------------------------------------------------------------------------------------
>
>
> Propriétés de la carte mère:
> Identifiant de la carte mère
> 51-0224-001437-00101111-071595-572$M572-V1.28679Release 02/24/1999 S
> Nom de la carte mère Inconnu
>
>
> --------[ Mémoire
> ]-----------------------------------------------------------------------------------------------------
>
>
> Mémoire physique:
> Total 255 Mo
> Utilisé 135 Mo
> Disponible 119 Mo
> Utilisation 53 %
>
> Zone de swap:
> Total 358 Mo
> Utilisé 80 Mo
> Disponible 278 Mo
> Utilisation 22 %
>
> Mémoire virtuelle:
> Total 614 Mo
> Utilisé 216 Mo
> Disponible 398 Mo
> Utilisation 35 %
>
> Problèmes et suggestions:
> Suggestion Installez
> davantage de mémoire système pour améliorer les performances des
> applications.
>
>
> --------[ Chipset
> ]-----------------------------------------------------------------------------------------------------
>
>
> Propriétés du chipset:
> Chipset de la carte mère Intel Triton
> 82430TX
> CAS Latency 3T
> RAS To CAS Delay 3T
> RAS Precharge 3T
> RAS Active Time 5T
> Taille du cache externe 512 Ko
> Type du cache externe Dual-Bank
> Pipelined Burst
> État du cache externe Activé
>
> Slots mémoire:
> Slot DRAM nº1 128 Mo (SDRAM)
> Slot DRAM nº2 128 Mo (SDRAM)
>
> Fabricant du chipset:
> Nom de l'entreprise Intel Corporation
> Information sur le produit
> http://www.intel.com/products/browse/chipsets.htm
> Télécharger le pilote
> http://support.intel.com/support/chipsets/index.htm
>
>
> --------[ BIOS
> ]--------------------------------------------------------------------------------------------------------
>
>
> Propriétés du BIOS:
> Type de BIOS AMI
> Date du BIOS système 07/15/95
> Date du BIOS vidéo 97/08/22
>
> Fabricant du BIOS:
> Nom de l'entreprise American
> Megatrends Inc.
> Information sur le produit http://www.ami.com/amibios
>
>
> --------[ Vidéo Windows
> --------------------------------------------------------------------------
>
> [ ATI Rage II+ PCI (ati_m64) ]
>
> Propriétés de la carte vidéo:
> Description du périphérique ATI Rage II+ PCI
> (ati_m64)
> Type de circuit Mach64: Rage II+
> Type de DAC Interne
> Pilotes installés ati_m64.drv
> Taille de la mémoire 2 Mo
>
> Fabricant de la carte vidéo:
> Nom de l'entreprise ATI Technologies
> Inc.
> Information sur le produit
> http://www.ati.com/products/home-office.html
> Télécharger le pilote http://www.ati.com/support/driver.html
>
> Problèmes et suggestions:
> Problème Il y a moins de
> 4 Mo de mémoire vidéo installés. Mettez à jour votre carte vidéo pour
> obtenir de meilleures performances.
>
>
> --------[ Vidéo PCI/AGP
> ]-----------------------------------------------------------------------------------------------
>
>
> ATI 3D-Rage II+ Carte vidéo
> ATI 3D-Rage II+ Accélérateur 3D
>
>
> --------[ Moniteur
> ]----------------------------------------------------------------------------------------------------
>
>
> [ ViewSonic VP171b ]
>
> Propriétés du moniteur:
> Nom du moniteur ViewSonic VP171b
> Identification du moniteur VSC0C11
> Modèle VP171b
> Date de fabrication Semaine 6 / 2004
> Numéro de série A1U040600116
> Taille d'affichage maximale visible 34 cm x 27 cm
> (17.1")
> Ratio d'aspect de l'image 4:3
> Fréquence horizontale 30 - 82 KHz
> Fréquence verticale 50 - 75 Hz
> Résolution maximale 1280 x 1024
> Gamma 2.20
> Gestion du mode DPMS Active-Off
>
> Modes vidéo gérés:
> 640 x 480 75 Hz
> 800 x 600 75 Hz
> 1024 x 768 75 Hz
> 1152 x 864 75 Hz
> 1280 x 1024 75 Hz
>
> Fabricant du moniteur:
> Nom de l'entreprise ViewSonic
> Corporation
> Information sur le produit
> http://www.viewsonic.com/products/desktop_display.htm
> Télécharger le pilote http://www.viewsonic.com/support/drivers.htm
>
> ==============================================================================
>
>
> what's the video BIOS ? Is there any upgrade I could do ?

The video card also has a BIOS. Forget about it.

>
> what's the cache level 2 ?

Cache speeds up the processor. On modern ones it's ON the processor, in the
chip package. Yours has it on the motherboard, which isn't as good but
that's the way it was done back then.

I don't read French real well but I don't understand why it reports the
right date in the BIOS string, 02/24/1999, but then turns around a few
lines later and says your system BIOS date is "07/15/95."

But, hmm, now that you mentioned L2 cache I notice it's got pipeline burst
active. Not that I know this is a good, or bad, thing but it reminded me
there are usually a number of cache settings on those boards and maybe you
should try safe settings on those.

> Thanks a lot !
>
> Claude
>
>
!