new case please help!

[da_kurlzz]

alright i just bought a new case for my homebuilt pc

but i dont know where the computer case: sound wires , power and reset wires , and other random wires go on my motherboard i tried combinations checked my motherboard manuel and dont understand so i was hopping for some help.

my motherboard manuel

http://www.asrock.com/mb/manual.asp?Model=AM2NF6G-VSTA&s=n


heres the groupes of wires my computer case i dont know where to put on my motherboard

groupe 1
power sw (white and blue wire together)
reset sw ( white and red wire together)

group 2
spkout R(green wire)
spkout L(white wire)
return L(blue wire)
return R(grey wire)
mic-in(red wire)
mic-base(yellow wire)
gnd (bkack wire)

group 3
gnd 1(bkack wire)
gnd 2(bkack wire)
+d 1(green wire)
-d 1(white wire)
+d 2(green wire)
-d 2(white wire)
+ 5v 1(red wire)
+ 5v 2(red wire)


so thanx for any help right now im really lost so thanx again

 

[da_kurlzz]

com on no anwser

 

[g-paw]

It's on page 21 under System Panel Header, case wires should have similar name on each set of wire anything followed by LED will be a light on the front of the, e.g., hard drive. The two most important are the power and reset. The front case sound, the beep when you start the computer should be a four pin connector. This is not the front speaker connector, there either on you sound card or somewhere else on the mobo if you're using on board sound

 

[alcattle]

Page #10 is board layout with the header names/numbers


groupe 1 go to #16 10 pins 10 blank
power sw (white and blue wire together) 6-8
reset sw ( white and red wire together) 5-7
pins 1-4 are for leds


group 2 go to #23 pin#8 blank
spkout R(green wire) #6
spkout L(white wire) #9
return L(blue wire)
return R(grey wire)
mic-in(red wire) #1
mic-base(yellow wire) #6
gnd (bkack wire) #2

Read page #20 for more

group 3 these are for USB ports, whichever is closest to front of board #15 or #17 pin #9 blank
gnd 1(bkack wire) #7
gnd 2(bkack wire) #8
+d 1(green wire) #6
-d 1(white wire) #4
+d 2(green wire) #5
-d 2(white wire) #3
+ 5v 1(red wire) #1
+ 5v 2(red wire) #2

Ask if you need more help

 

[da_kurlzz]

i really dont get if u can explain more about the numbers it would be great\

sorry im such a nub with case wireing


thanks for the help doh

 

[Mondoman]

If you're having this much trouble on something that is so basic to setting things up properly and not frying your computer or injuring yourself, you really need to get someone to help you in person, not over a text forum like this. It should be pretty easy to learn that way, but it is more likely than not that you will misconnect something with bad results this way.

 

[da_kurlzz]

i know witch port to put them om i just dont know witch pins on the port

when u refernece #10 do u me the port in the book and by numbers by pins???

 

[alcattle]

first #10, page in manual, second #10 is number of pins total, third #10 means that pin is missing from the set. all sets start #1 at bottom left and #2 top left. even number on top, odd on bottom with one pin missing on every set.

 

[da_kurlzz]

Thank You alcattle evreything works fine now thank u for ur time and supporti very much aprreciate it ..




thanks

 

[alcattle]

Glad to hear it, stop by and lend a hand now that you are no longer a rookie