Sign in with
Sign up | Sign in
Your question

Pls. tel me how can i lower my Ram Frequency from 333 to 266

Last response: in Memory
Share
May 7, 2007 8:15:20 AM

Pls. tel me how can i lower my Ram Frequency from 333 to 266 and where i need to go?kindy advise me on how?
May 7, 2007 8:26:24 AM

i have a ddr2 667 5-5-5-15-20 2T timing on stock, they said if i lower it to 4-4-4-12-161T it will be much faster???is it correct?do i need to lower or match the frequency?or i will just leave it that way?? 4-4-4-12-16 1T 333 frequency???kindly advise..
May 7, 2007 8:37:36 AM

Quote:
i have a ddr2 667 5-5-5-15-20 2T timing on stock, they said if i lower it to 4-4-4-12-161T it will be much faster???is it correct?do i need to lower or match the frequency?or i will just leave it that way?? 4-4-4-12-16 1T 333 frequency???kindly advise..


Uh.. no.
Higher clocks > Tighter timings.

You will lose a lot of performance going to 667 CL5 to 533 CL4.
Related resources
May 7, 2007 8:53:41 AM

So what is the correct timmings for ddr2 667 Kingston value ram 1gb? i saw on cpu z it can be 3-3-3-9-12 1T,4-4-4-12-16 1T,5-5-5-15-20 2T please help?i want my ram to run faster and stable than stock
May 7, 2007 9:40:54 AM

The ram speed needs to be matched to your cpu's front side bus speed, ideally at 1:1 but using a ratio if not (note current Intel processors at stock speed and multiplier ie. 1066 fsb can't usually be run at 1:1). The auto setting in your BIOS will normally take care of this.

Slowing your ram to slower speeds than the FSB will severely slow your system down as you'll bottleneck it.

If you want to tighten timings, go to the manufacturers web site and look up your ram. Timings should be listed. Set these timings in your bios.

These are usually the guaranteed timings. If you want to try tighter timings, then increase the timing speed in steps of 1 unit and see if your computer a) posts and b) passes a test with memtest 86.

The most important element to try 1st is the jump from 2T to 1T. This can be adjusted before touching any other timings.

If your system passes both tests then those tighter timings are ok. If you want to try further, tighten them further. When your pc no longer posts or passes memtest, or both, thats the time to back the timings off a little until you get successful results in both once more.
May 7, 2007 9:51:23 AM

Thank you very much!!! i will try it when i go home!!! i hope i can play fear and titan quest much faster?? on higher settings


P4HT 3.4 OC
P4N SLI MOBO
2X 1 GB HYPER X DDR2 667
2X 1 GB KINGSTON VALUE RAM DDR2 667
2X7600 GT OC
2X 259 HD ON RAID 0
ATRIX 500T EXTREAM POWER DUAL RAIL
May 7, 2007 9:57:24 AM

Thank you very much!!! i will try it when i go home!!! i hope i can play fear and titan quest much faster?? on higher settings


P4HT 3.4 OC
P4N SLI MOBO
2X 1 GB HYPER X DDR2 667
2X 1 GB KINGSTON VALUE RAM DDR2 667
2X7600 GT OC
2X 259 HD ON RAID 0
ATRIX 500T EXTREAM POWER DUAL RAIL
May 7, 2007 10:07:44 AM

Actualy i have 2x 8800gts 320 oc but im reserving it for the mobo that i am building right now....i only need a board, cpu then i will be up and running!any advise for a good mobo and cpu thats not that expensive but with a good and fast performance cause iam kinda short i spend too much on my gpu's...actualy i run every game on my rig on high and somtimes max without a glitch! only titan quest it is my prob?i exp hangs and lags but not that big only slight i want this to disapear, i think with a right settings it will run smoothly.


P4HT 3.4 OC
P4N SLI MOBO
2X 1 GB HYPER X DDR2 667
2X 1 GB KINGSTON VALUE RAM DDR2 667
2X7600 GT OC
2X 259 HD ON RAID 0
ATRIX 500T EXTREAM POWER DUAL RAIL
May 7, 2007 10:29:05 AM

i bought alraedy a thermaltake purepower 700watts psu...i think its enough? 48A???? i cant believe it??? the 680i and 650i is my prob?its very exppensive????!!!!
May 7, 2007 12:52:40 PM

I saw this striker board and evga board but the cheapest with the same perormance mobo i saw is msi p6n sli platinum at around 850SR is it good brand and mobo with a good performance and quality
!