Q6600 Temps

Just got my system up and running and my Q6600 is running at 43-44C is this too hot?

Register or log in to remove.

Well that all depends. First off you need to get a few programs to understand what you are looking at. First, get CPU-Z. This program will let you know which stepping revision you have. If it is the G0 stepping and you are using an aftermarket heatsink then you do have a problem. You also want to get coretemp 0.96.1. This program is extremely accurate on detecting temps. If you read up on their site intel and amd finally gave them the correct formula to find the temps apparently. Anyhow, I just finished doing a Q6600 build with a Zalman 9700 aftermarket heatsink and used arctic silver 5 thermal paste and the temps are around 19-24 at idle and around low 40s under full load on all 4 cores with prime95 running all night. So yeah your temps sound a bit high, however, if you have the stock heatsink/fan and have the thermal paste that came on that HSF then temps are going to be higher. Also, if it is B2 stepping then it will be hotter. I think B3 and G0 are similar, however, go is going to run cooler.

Anyways man good luck with everything. When you build find the stepping that you want. ClubIT is great for giving you stepping specific processors for around the same price as Newegg gives non stepping specific processors. This means with the Egg you have no idea what you are getting. Might get gold, might get poop. Never know. Anyways, good luck.

Message quoted 1 times

------------------------------ Gahleon Mod
http://img340.imageshack.us/my.php [...] 023yj7.jpg
http://img340.imageshack.us/my.php [...] 068gb0.jpg
Reply to gahleon

I also just installed a Q6600 about 45mins ago. I have it OC'ed @3.01 and it idles at 19-22c so and gets around 38-40c under load so these are pretty similar to gahleon. I am using an ASUS Silent Knight II cooler seems to be working pretty well. I have the G0 stepping. So yours does seem a bit high???

Message quoted 1 times

Reply to will31

gahleon wrote :

Well that all depends. First off you need to get a few programs to understand what you are looking at. First, get CPU-Z. This program will let you know which stepping revision you have. If it is the G0 stepping and you are using an aftermarket heatsink then you do have a problem. You also want to get coretemp 0.96.1. This program is extremely accurate on detecting temps. If you read up on their site intel and amd finally gave them the correct formula to find the temps apparently. Anyhow, I just finished doing a Q6600 build with a Zalman 9700 aftermarket heatsink and used arctic silver 5 thermal paste and the temps are around 19-24 at idle and around low 40s under full load on all 4 cores with prime95 running all night. So yeah your temps sound a bit high, however, if you have the stock heatsink/fan and have the thermal paste that came on that HSF then temps are going to be higher. Also, if it is B2 stepping then it will be hotter. I think B3 and G0 are similar, however, go is going to run cooler.

Anyways man good luck with everything. When you build find the stepping that you want. ClubIT is great for giving you stepping specific processors for around the same price as Newegg gives non stepping specific processors. This means with the Egg you have no idea what you are getting. Might get gold, might get poop. Never know. Anyways, good luck.

Ok I have the G0 stepping, and I ran coretemp its showing my temp at 42C im also running the stock heatsink so im gonna pick up a Zalman 9700.

Reply to Rohmaan

Download the program "coretemp" its the easiest way to find out your q6600s real temps. 40c under load....especially for an overclocked CPU does not sound correct.

@Rohmaan what's your cooling solution, and how much thermal compound did u use.

Message quoted 1 times

------------------------------ Q6600 B3 @ 3.3Ghz Air 1.37v (36c Idle: 65c 100%Load) <--hottest core || Zalman 9500
BFG 680i SLI Mobo 1466 FSB (for 366x9) || 2GB GSkill DDR2 800 @ ~900Mhz 2.075v 4-4-4-12
evga 8800 GT (S.C. ed.) || Antec Titan Server Case || Vantec Stealth || 13,949
Reply to PlasticSashimi

I don't see an issue with that as a core temp

------------------------------ jennyh wrote: AMD break-even Q4 2009. *Gauranteed*

RabidFanboysSpreadingFalse.Info
Reply to TechnologyCoordinator

42c sound about right for stock cooling...rohmaan.

You really only need better cooling if you're going to OC...which is kind of a no brainer with a q6600...

that zalman will get you to around 3.4 easy in my opinion.

------------------------------ Q6600 B3 @ 3.3Ghz Air 1.37v (36c Idle: 65c 100%Load) <--hottest core || Zalman 9500
BFG 680i SLI Mobo 1466 FSB (for 366x9) || 2GB GSkill DDR2 800 @ ~900Mhz 2.075v 4-4-4-12
evga 8800 GT (S.C. ed.) || Antec Titan Server Case || Vantec Stealth || 13,949
Reply to PlasticSashimi

Guys, if you want to know whether your temps are accurate, then check out the Core 2 Quad and Duo Temperature Guide: http://www.tomshardware.com/forum/ [...] ture-guide

You can learn how to test, calibrate and monitor CPU and Core temperatures so that you're certain they're correct.

Comp :sol:

------------------------------ i7 920 @ 4.1 | Vcore Load 1.360
61c CPU & 66c Core @ 22c Ambient
Xigmatek HDT-S1283 | Push-Pull Fans
Core i7 and Core 2 Temperature Guide --> http://www.tomshardware.com/forum/ [...] ture-guide
Reply to CompuTronix

Trust me the temps are correct under load. First off as I said it isn't stock cooling under load that I am attaining the around 40C temps, it is with a zalman 9700. The CPU is at stock speeds as of right now. It is perfectly normal for this stepping to have low temps and those temps are right under prime 95. Anyways, as the dude above said check out the tomshardware guide! Toms PWNS!

Message quoted 1 times

------------------------------ Gahleon Mod
http://img340.imageshack.us/my.php [...] 023yj7.jpg
http://img340.imageshack.us/my.php [...] 068gb0.jpg
Reply to gahleon

gahleon wrote :

Trust me the temps are correct under load. First off as I said it isn't stock cooling under load that I am attaining the around 40C temps, it is with a zalman 9700. The CPU is at stock speeds as of right now. It is perfectly normal for this stepping to have low temps and those temps are right under prime 95. Anyways, as the dude above said check out the tomshardware guide! Toms PWNS!

Was just a bit of confusion I think

G0 stepping + zalman 9700 + stock 2.4ghz = your temps on load

sounds accurate to me

Message edited by PlasticSashimi on 01-30-2008 at 08:08:41 PM

------------------------------ Q6600 B3 @ 3.3Ghz Air 1.37v (36c Idle: 65c 100%Load) <--hottest core || Zalman 9500
BFG 680i SLI Mobo 1466 FSB (for 366x9) || 2GB GSkill DDR2 800 @ ~900Mhz 2.075v 4-4-4-12
evga 8800 GT (S.C. ed.) || Antec Titan Server Case || Vantec Stealth || 13,949
Reply to PlasticSashimi

Im getting 42C idle 53C under load.

Reply to Rohmaan

PlasticSashimi wrote :

Download the program "coretemp" its the easiest way to find out your q6600s real temps. 40c under load....especially for an overclocked CPU does not sound correct.

@Rohmaan what's your cooling solution, and how much thermal compound did u use.

Im running stock cooling

Reply to Rohmaan

Ok I ran prime95 for 1 minute and in coretemp my temps jumped to 70C

Reply to Rohmaan

Well those temps are a bit on the uncomfortable side...but nothing too dangerous in the short term.

My advice is to keep "Intel Speed Step" or whatever CPU throttling is available in your BIOS activated and don't overclock your CPU (at least just yet).

Spend 40-50 bucks and get a decent third party cooler for your CPU sometime in the near future and then you'll be set.

You could try to re-seat the CPU, but honestly I'd just wait to do that until I got the better cooler, since doing that is a bit of a pain.

What voltage are you running to the chip? If it's @ stock speeds you might be able to reduce the voltage and thus the heat.

Message quoted 1 times

------------------------------ Q6600 B3 @ 3.3Ghz Air 1.37v (36c Idle: 65c 100%Load) <--hottest core || Zalman 9500
BFG 680i SLI Mobo 1466 FSB (for 366x9) || 2GB GSkill DDR2 800 @ ~900Mhz 2.075v 4-4-4-12
evga 8800 GT (S.C. ed.) || Antec Titan Server Case || Vantec Stealth || 13,949
Reply to PlasticSashimi

PlasticSashimi wrote :

Well those temps are a bit on the uncomfortable side...but nothing too dangerous in the short term.

My advice is to keep "Intel Speed Step" or whatever CPU throttling is available in your BIOS activated and don't overclock your CPU (at least just yet).

Spend 40-50 bucks and get a decent third party cooler for your CPU sometime in the near future and then you'll be set.

You could try to re-seat the CPU, but honestly I'd just wait to do that until I got the better cooler, since doing that is a bit of a pain.

What voltage are you running to the chip? If it's @ stock speeds you might be able to reduce the voltage and thus the heat.

I re-seat the CPU, and heatsink its making good contact nothings blocking the fan my voltage is 1.176.

Reply to Rohmaan

Well the voltage is low if anything...so that can't be the source of the heat. The Q6600 is just a hot CPU so it's no wonder that it gets in the 70c range with the stock heatsink....

(I ran prime95 on my work comp, dual Quad Xeon chips, and they made it to the mid 80s in under 2 mins)

If you don't plan to overclock...you'd probably be fine....but 50 bucks is not too much for peace of mind and a nice overclock.

------------------------------ Q6600 B3 @ 3.3Ghz Air 1.37v (36c Idle: 65c 100%Load) <--hottest core || Zalman 9500
BFG 680i SLI Mobo 1466 FSB (for 366x9) || 2GB GSkill DDR2 800 @ ~900Mhz 2.075v 4-4-4-12
evga 8800 GT (S.C. ed.) || Antec Titan Server Case || Vantec Stealth || 13,949
Reply to PlasticSashimi

did you try reseating the cpu fan

Message quoted 1 times

Reply to cal8949

cal8949 wrote :

did you try reseating the cpu fan

Yes

Reply to Rohmaan

At stock voltages with no overclocking and it being idle depending on the room temperature are all the variables.

if your room is 70 degrees, you have good airflow through the case and its at idle with no overclock and stock voltages yes that is high. However its not in any sort of danger because i've seen mine go over 70c without any sort of stability problems. Granted that is at a high overclock on voltage and fsb and it had prime 95 running with 4 cores on small ftp.

Message quoted 1 times

------------------------------ A+ Certified 220-601 and 602
Antec Nine Hundred Gaming case/Core I7 920/Asus P6TSE/EVGA GTX 260/4GB OCZ 1600/Win 7 64bit

Reply to cranbers

cranbers wrote :

At stock voltages with no overclocking and it being idle depending on the room temperature are all the variables.

if your room is 70 degrees, you have good airflow through the case and its at idle with no overclock and stock voltages yes that is high. However its not in any sort of danger because i've seen mine go over 70c without any sort of stability problems. Granted that is at a high overclock on voltage and fsb and it had prime 95 running with 4 cores on small ftp.

You need to spend more time in the OC section.

A) 71.4C is the Intel Max Spec for a Q6600 (Tcase).
B) Cores run at a dT of 10+/-3C of the Tcase.
C) Saying "it's running at xx Degrees" means nothing without saying what sensor it is.

I *HEAVILY* advise the OP to read the guide posted by Computronix. It is very informative.

------------------------------ TeamBAG Member
Reply to cnumartyr

will31 wrote :

I also just installed a Q6600 about 45mins ago. I have it OC'ed @3.01 and it idles at 19-22c so and gets around 38-40c under load so these are pretty similar to gahleon. I am using an ASUS Silent Knight II cooler seems to be working pretty well. I have the G0 stepping. So yours does seem a bit high???

19c is your idle temp, that is 66 degrees f? What is the temp in the room its kept in? That is one thing that has to be considered here. The temp of the cpu will never go below what the temp is in the room, now add in a computer case that is cramped full of heat generating components, your system temps are definitely not normal or even average. You must have your computer in a room that doesn't have heat in the winter.

If someone keeps their computer in a room that is 75 degrees and has a computer that isn't all that well ventilated, its going to idle warm, no matter what.

Message quoted 1 times

------------------------------ A+ Certified 220-601 and 602
Antec Nine Hundred Gaming case/Core I7 920/Asus P6TSE/EVGA GTX 260/4GB OCZ 1600/Win 7 64bit

Reply to cranbers

cranbers wrote :

If someone keeps their computer in a room that is 75 degrees and has a computer that isn't all that well ventilated, its going to idle warm, no matter what.

What about active heat rejection?

My room is normally 22-24C, my CPU idles at 25-26C.

------------------------------ TeamBAG Member
Reply to cnumartyr

edit sorry

Message edited by lightsout714 on 01-28-2009 at 08:42:32 PM

Reply to lightsout714

Forum CPU & Components : CPUs - Q6600 Temps

Please mind

Become a fan

Q6600 Temps

Forum CPU & Components : CPUs - Q6600 Temps

Please mind