Give me a hand since i spend alot of money....to get this,,,, rating.
1st In 3d Mark06 Rating only got 10409 bad rating.....Sad
2nd My board only shonw 800mhz
3rd His graphic won't automaticallly adjust fan speed.
4th Vista 32 always hanging....
another 1 issue, when lunch game it hanging..
please help for a sulation...maybe griphic card got problem? since rating bad, hang when lunching game....
76C' when starting lunching Vista 32bit sp1.
before that i tried CPU score in 3dmark06 is 0-1...
i doing uninstall new ati driver , to install previous version intead.
Fan speeding 1sec only when during restart. it when speeding in window, only the way is River tune...
I did auto tune in crystalyst, but fails with hanging.... WHY?????
Assuming that all the hardware is working. Some adjustments to the bios are needed. Insure that all of the latest and greatest drivers are installed. Check control panel power options set to home/desktop pc. 10.5+/-k+ is not that bad for a cpu running at 2.2ghz. Try some bios adjustments. CPU-Z? GPU-Z? You might install Riva tuner for the vc.
"2nd My board only shonw 800mhz"? Is this for the ram? Manual setting in bios with correct voltage ajustment.
After reading the last couple of posts about Games slow/ hang to load I am wondering about the raid setup. Double check that the whole HD/ raid system is setup correctly especially the drivers for vista. This may be the source of your problems.
pcpitstop.com
Message edited by topper743 on 05-03-2008 at 08:50:02 PM
LPCIO
-----------------------------------------------------
Vendor ITE
Model IT8718
Vendor ID 0x90
Chip ID 0x8718
Revision ID 0x4
Config Mode I/O address 0x2E
Processors Information
------------------------------------------------------------------------------------
Processor 1 (ID = 0)
Number of cores 4 (max 4)
Number of threads 4 (max 4)
Name AMD Phenom 9500
Codename Agena
Specification AMD Phenom(tm) 9500 Quad-Core Processor
Package Socket AM2+ (940)
CPUID F.2.2
Extended CPUID 10.2
Brand ID 10
Core Stepping DR-B2
Technology 65 nm
Core Speed 1105.3 MHz (5.5 x 201.0 MHz)
HT Link speed 1808.7 MHz
Stock frequency 2200 MHz
Instructions sets MMX (+), 3DNow! (+), SSE, SSE2, SSE3, SSE4A, x86-64
L1 Data cache 4 x 64 KBytes, 2-way set associative, 64-byte line size
L1 Instruction cache 4 x 64 KBytes, 2-way set associative, 64-byte line size
L2 cache 4 x 512 KBytes, 16-way set associative, 64-byte line size
L3 cache 2 MBytes, 32-way set associative, 64-byte line size
FID/VID Control yes
FID range 5.0x - 11.0x
max VID 1.250 V
Features XD, VT
Package Type 0x1
Model 95
String 1 0x2
String 2 0x0
Page 0x0
Attached device PCI device at bus 0, device 24, function 0
Attached device PCI device at bus 0, device 24, function 1
Attached device PCI device at bus 0, device 24, function 2
Attached device PCI device at bus 0, device 24, function 3
Attached device PCI device at bus 0, device 24, function 4
Looks like your CPU is running fine in your 3dmark its about right. However, your gfx score is massively low for a 3870X2. Also your CPU temps are fairly high if thats 46C idle. Try re-seating your heatsink. Or turn Cool and Quiet off in your BIOS.
As for getting your 3870X2 to run properly it's about 3-4k points out on 3dmark. I seriously doubt your spider platform is lacking in bandwidth so bottlenecking shouldn't a cure. Is CrossfireX enabled in CCC?
Yor ram probably needs timings and voltages set manually in the Bios. And since you are running 4g it will nee .1-.2 more volts then it says.
Your CPU is bottlenecking that video card. Systems that get close to 20000 score are running Intel Quads at 4.0 or higher your running 2.2, seems like the score is about right.
Message edited by roadrunner197069 on 05-03-2008 at 09:27:13 PM
CCC menas?
My HDD sometime got old HDD sound but still working proper..
thanks you i gtg sleep woking tomorrow try to help me solve my pc problem.
chat tomorrow. hope to see you again
YOu can keep going, i'll check tomorrow. thanks