New to overclocking need help -q9550

[dupp]

Hi i would like to overclock my q9550 to 3.6 ghz because my gtx 295 is bottlenecking that cpu i think :S
heres my computer specs:
asus gtx 295
gigabyte GA-EP45T-DS3R
yorkfield q9550
antec nine hundred
750w coolermaster
CORSAIR XMS3 4GB (2 x 2GB) 1333mhz ddr3 9-9-9-24 1.7V
OS: vista 64bit home premium

I'm new to overclocking, ive seen a good guide to overclock under my own bios, please if you have time, change the following information to what i would need, thank you very much.

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Fast
CPU Clock Ratio ..........................: 8
Fine CPU Clock Ratio.....................:.5
CPU Frequency ...........................: 3.612


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 425Mhz
PCI Express Frequency (Mhz) .........:Set to 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 50-150
MCH Clock Skew (ps)...................: <<< 150-250


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.00D
Memory Frequency (Mhz) ..............: 850Mhz
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................4/5
tRCD .........................................4/5
tRP'...........................................4/5
tRAS..........................................12/15

^^^ You may be able to get 544-12 or 544-15, but if not should be able to use 555-12 ^^^

Advanced Timing Control
tRRD...........................................3-5
tWTR..........................................4-8
tWR............................................5-10
tRFC...........................................56-72
tRTP...........................................4-6
Command Rate (CMD) ....................:2

Driving Strength Profiles
Driving Strength ............................800-1066

Channel A
Static tRead Value.........................:9-12

 tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

Channel B
Static tRead Value.........................:9-12

 tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: All up to your chip.  Keep in mind what you set here is not what you get in windows (You can check the difference with CPU-z, but it is also not always the same and may vary at different volt ranges)......  I see some do 3.6+ on 1.24 or Less Actual, some need 1.25-1.3 or more.  So set high enough for sure to boot then you can lower later

CPU Termination…..... 1.200V*.......: <<< 1.24-1.38
CPU PLL…………………....1.500V*.......: << Please set to stock, Auto overvolts this way to much

CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly

CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly

MCH/ICH
MCH Core…………….....1.100V...........: << 1.25-1.35
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< 1.55-1.6
ICH Core…………...……1.100V............: <<< 1.1x-1.2

DRAM
DRAM Voltage ……....1.800V............: 2.0-2.1
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

[/quote]

 

[RJR]

How about you do a little more research and try learning how to overclock yourself.

You can't just tell someone all the settings they will need, every chip,mb,ram is different.

Then, if you get stuck come back and ask a question. Thank you very much.

 

[fedtmusen]

Easy Tune6 can be used to change those values, but from windows.
Se the changes before and after using Easy Tune6. Start slow...but you could be there in a rather fast time, like 10 minutes, tjeck temps, a lot!
Should be on your drivers disk. Works for 64bit too.
As JRJ wrote, research is the thing.
I got my q9450 from 2.666 to 3.666 with Easy Tune6, stable.
I too, dont know much about OC, but this non-value -can start many things, like research.
Happy days

 

[dupp]

i done alot of research b ut its different for every rig ive seen a post on another forum, som1 just told him all the values he needed, i would apreciate it soo much i dont know what are tha values that im needing, sorry if my english is bad :S

Thank you.