Tom's Hardware > Forum > Overclocking > CPUs > Prime95 error codes

Prime95 error codes

Forum Overclocking : CPUs - Prime95 error codes

Tom's Hardware: Over 1.4 million members in 6 different countries available to answer all your high-tech questions. Sign up now! Its free!
Ask the community Add a reply
Word :    Username :           
 
drums101   05-16-2009 at 08:48:34 AM

Ok so I am overclocking my e7300. I have it at 3.4ghz with voltage at 1.272v. I run prime95 and it runs for like 2 hours and then stopped only on one core and gave me this error message. FATAL ERROR: Final result was 16295BCF, expected: C75824DB I have searched high and low and cannot find out what that means. Do I need to up the core voltage? I have my ram which is 4gb of ocz 800mhz ram 2x2gb at 1.9 volts. Cooling is not an issue. I just cant figure out what the damn error code means. Any suggestions to prevent the error and make it stable? let me know if you need more info. Thanks any suggestions would be great!

------------------------------ Core i7 950@ 4GHZ-6gb Corsair Dominator 1600mhz-GTX285 OCX SLi-ASUS P6T Deluxe V2-WD 300GB Velociraptor
Add a reply
Sponsored Links
Register or log in to remove.
blackpanther26   05-16-2009 at 09:41:49 AM
- 0 +

More than likly you'll have to up the vcore.

------------------------------ http://valid.canardpc.com/cache/banner/631829.png
http://valid.canardpc.com/cache/banner/549389.png
 Reply to blackpanther26
MaDMagik   05-16-2009 at 04:44:32 PM
- 0 +

+1^

Up the voltage by a notch or two, test again

Reply to MaDMagik
drums101   05-16-2009 at 07:02:25 PM
- 0 +

ok thanks I will try that.

------------------------------ Core i7 950@ 4GHZ-6gb Corsair Dominator 1600mhz-GTX285 OCX SLi-ASUS P6T Deluxe V2-WD 300GB Velociraptor
 Reply to drums101
drums101   05-16-2009 at 07:07:57 PM
- 0 +

Another quick question I have the voltage set to like 1.3065 in the BIOS but then why does it shoe up as 1.28 in cpuz and pcwizard2008? which one is more accurate?

------------------------------ Core i7 950@ 4GHZ-6gb Corsair Dominator 1600mhz-GTX285 OCX SLi-ASUS P6T Deluxe V2-WD 300GB Velociraptor
 Reply to drums101
MaDMagik   05-16-2009 at 11:02:44 PM
- 0 +

They both are. Vcore reported inside windows will always be lower than whatever you set it to in bios. Its called Vdrop i believe. When posting always use the one reported by cpu-z, same thing applies when you read other peoples posts.

Reply to MaDMagik
drums101   05-17-2009 at 12:30:03 AM
- 0 +

ok thanks man that makes sense I have heard that term before

------------------------------ Core i7 950@ 4GHZ-6gb Corsair Dominator 1600mhz-GTX285 OCX SLi-ASUS P6T Deluxe V2-WD 300GB Velociraptor
 Reply to drums101
ragsters   05-17-2009 at 02:46:28 AM
- 0 +

Use LinX for about 25 passes to check if your Voltages are OK. After that use prime 95 blend for about 6-8 hours.

Reply to ragsters
Ask the community Add a reply
Tom's Hardware > Forum > Overclocking > CPUs > Prime95 error codes
Go to:

There are 1210 identified and unidentified users. To see the list of identified users, Click here.

Forum map
Bestofmedia Forum ©
2000-2009 Bestofmedia Group
Page generated in 0.250 seconds
Sponsored links
  • Ask the community now
  • Publish
Ad
Related Topics
See all relatives topics
They won a badge
Join us in greeting them