Tom's Hardware > Forum > Homebuilt Systems > New System Build > Can't get new computer working

Can't get new computer working

Forum Homebuilt Systems : New System Build - Can't get new computer working

Tom's Hardware: Over 1.4 million members in 6 different countries available to answer all your high-tech questions. Sign up now! Its free!

Ask the community Add a reply

Bottom Search this thread

Asus M4A79 Deluxe, AMD 790FX, AMD2+
WD VelociRaptor 150GB sata
AMD Phenom II X4 940/AM2+ 3GHz 6MB
Zalman 9500ALED CPUCooler
Thermaltake V9 Black 23Cm Fan
CoolerMaster Real Power Modular - 850W
Corsair TWIN2X4096-8500C5D, 2x2048mb
Asus ENGTX285/HTDP/1GD3, GDDR3, PCI-E

the fans starts working, and the gfx shows green light, but the monitor remains in standby. i have removed one of the dominator corsair ram, tried to put the gfx card in different pci-e slots, and tried with a different monitor.

Do you have any suggestions, im starting to get short on ideas.

Add a reply

Try getting an older cpu to update the Bios with and then it should work

Reply to Helloworld_98

i would do the obvious when going with a phenom 2 ...that is, check again if i have the newest bios installed for the motherboard...since most am2+ boards do require a bios update for phenom 2 to work... unfortunately some boards wont even post with an x4 940 so u cannot update the bios...the only way left is to use an older supported proc to update it first...
....try doing it if u have an older x2 or sempron or take it to a local computer shop may be they can help in flashing it for you..

http://support.asus.com/download/d [...] uage=en-us

Reply to mbbs20

plugged an old pci radeon in, and it started up. Doesn't an m4a79 deluxe board support nvidia cards, or was the gtx285 just damaged ?

Reply to nuclearcola

Did you have both 6-pin power connectors plugged in to the GTX 285?

Reply to shortstuff_mt

yeah, and then it lighted green, with one 6-pin it lighted red, but no difference with the boot.

Reply to nuclearcola

Was it seated all the way?

------------------------------ CM HAF 932 - 300GB Velociraptor
GIGABYTE GA-EP45T-DS3R
E8500 - Sapphire 1Gb 4850
4G DDR3 OCZ Reaper 1333
Reply to aford10

yeah, even tried to bend the metal, where you put the screw down, to see if i could get the card further down. But nothing, just the same, haven't tried pci-e before, so maybe there's something special im doing wrong.

Reply to nuclearcola

are you sure it isnt POSTING?

do you have the case speaker attached and is it making any beeps at all when it powers on?
If the case speaker isnt in put it in now and it will tell you what is wrong with a beep code

Reply to Outlander_04

try pluggin the monitor into the OTHER dvi port on the card

And for single card use, read the manual for which slot to have it in. It won't work in the wrong one..

Message edited by doormatderek on 02-20-2009 at 10:54:55 PM

Reply to doormatderek

Ask the community Add a reply

Tom's Hardware > Forum > Homebuilt Systems > New System Build > Can't get new computer working

Go to:

Help |
Forum rules

There are 580 identified and unidentified users. To see the list of identified users, Click here.

Page generated in 0.551 seconds

Please mind

You are about to answer a thread that has been inactive for more than 6 months.
If you still wish to proceed, please ensure that your posting is original and does not duplicate or overlap any prior responses to this thread.

Add a reply Cancel

Focus On

Can't get new computer working

Forum Homebuilt Systems : New System Build - Can't get new computer working

Please mind