HELP ME O.C FOR E5200 + GA-G41M-ES2L

[zadt_pro]

HEY GUYS...
CAN I REACH 3.5 - 3.7 Ghz with E5200 CPU WITH G41 MOBO?
I HAVE TRY E8400 AND E5300 CPU
THE HIGHEST O.C I CAN GET IS
-E8400 OC 3.08GHZ (9 X 343)
-E5300 OC 3.12GHZ (13 X 240)
ga - g41m - es2l
2 x 2046 CORSAIR DDR2 800 RAM
TEMP : ~ 36c - 62c Max
100% STABLE..
I TEST ALL WITH INTEL BURN TEST 2.5
PASS ALL 25 TESTS WITH MAX STRESS.

I WANT TO BUY E5200.BUT CAN IT GET 3.5Ghz O.C?
HELP...
IM NOOB LOL...
I Have read from this forum and they say e5200 can get more higher in o.c then e5300..
so can i get high o.c with e5200?
please help me...
any suggession?

 

[d1rtyju1c3]

You should be able to Hit 4ghz with any of the above CPU's.

 

[d1rtyju1c3]

Post your PC configuration.

 

[zadt_pro]

GA-G41M-ES2L (BIOS VER: F9)
CPU E5300 @ 2.60GHz
Core Speed 3120.3 MHz
Multiplier x FSB 13.0 x 240.0 MHz
Rated Bus speed 960.1 MHz
Stock frequency 2600 MH
Max VID 1.288 V
Max.Temp ~52°C (Core #0)
~52°C (Core #1)
---
CORSAIR CGM2X2G800
PC2-6400
2 x 2048 DDR2
400.0 MHz (3:5)
5-5-5-18
~1.8v
-ASUS EN9500GT O.C 512M DDR3
-INTEL STOCK COOLER.
-PSU ORBIX ATX-VST 480X
--
Hardware monitor ITE IT87
~ 1.23 V (CPU VCORE)
~ 1.89 V (VIN1)
~ 3.28 V (+3.3V)
~4.95 V (+5V)
~ 3.07 V (+12V)
~ 5.16 V (+5V VCCH)
~ 3.10 V (VBAT)
--

 

[zadt_pro]

-WINDOWS 7 ULTIMATED
-WINDOWS 7 ULTIMATED x64.
i will be able to hit 4.0Ghz with e5200?
I should try e5200 later..
thanks

 

[zadt_pro]

i want to knw which of this cpu is the best that able to hit 3-5ghz - 4.0ghz with
(41M-ES2L + DDR2 800)
E5300 or E5200?
any suggession?

 

[d1rtyju1c3]

You may be able to get the E5300 there with slightly lower temps but they would both get to 4ghz, If you purchased an aftermarket cooler. The stock intel cooler wont cut it.
The safe load temps for a 24/7 overclock is 70c for the Core2duo's and you are already at 62c at 3.1ghz which is pretty good but you wont be able to 4ghz unless you upgrade the cooler.
The E8400 will probably do it better than either one of the E5000 CPU's would, and run a lot cooler. I have had an E8400 to 4.2ghz on air but you need an aftermarket cooler to do it. You can run an E8400 at 3.6ghz on stock voltage.

 

[jsc]

Whether or not you can reach 4 GHz with an E5200 or E5300 will depend on your particular chip. The best I was able to do with my E5200 was 3.78 GHz. (315 MHz X 12). I even tried increasing vcore to 1.6 volts.

The E8400 will not be able to reach 4.0 GHz in a G41 board. The internal multiplier is too low and the G41 FSB freq usually will not go much past about 350 MHz.

 

[d1rtyju1c3]

I never even thought about the motherboard limitations, I was just thinking about what the CPU's could do.

jsc is right "The E8400 will not be able to reach 4.0 GHz in a G41 board. The internal multiplier is too low and the G41 FSB freq usually will not go much past about 350 MHz".

sorry for leading you the wrong way.

 

[jsc]

That's why they call it a system.

I really like the little G'byte G41 boards. I have built several good, solid, cheap systems - mostly for others.

 

[d1rtyju1c3]

That's why they call it a system.

I really like the little G'byte G41 boards. I have built several good, solid, cheap systems - mostly for others.

I know, I have just never dealt with the G41 boards before.
I just thought they would overclock similar to a P45. I guessed wrong.

I do know if the onboard graphics is disabled(using dedicated graphics card)you can push the OC a littlre more. Correct me if Im wrong.

 

[zadt_pro]

Im using dedicated graphic card..The max limit i can reach is 3.24Ghz (13.5 x 240).Higher then that it BSOD at windows startup.
It POST at (10 x 333) ~3.3Ghz and (12 x 300) ~3.6Ghz..
Is that my PSU or this cheap G41M-ES2L mobo that wont let me pass over 3.24Ghz ???
I have try etc...Vcore ~1.45v..It wont pass windows startup..BSOD!!!
Im noob..

"Sorry for my bad english "