[Solved] Help me overclock my 1100T Phenom BE!

I was using CPu-Z to monitor. No burn in tests though. Never really thought about it!
I was just slowly upping the ratio and fsb till it crashed then brought it back down.


Processors
-------------------------------------------------------------------------

Number of processors 1
Number of threads 6

APICs
-------------------------------------------------------------------------

Processor 0
-- Core 0
-- Thread 0 0
-- Core 1
-- Thread 0 1
-- Core 2
-- Thread 0 2
-- Core 3
-- Thread 0 3
-- Core 4
-- Thread 0 4
-- Core 5
-- Thread 0 5

Processors Information
-------------------------------------------------------------------------

Processor 1 ID = 0
Number of cores 6 (max 6)
Number of threads 6 (max 6)
Name AMD Phenom II X6 1100T
Codename Thuban
Specification AMD Phenom(tm) II X6 1100T Processor
Package Socket AM3 (938)
CPUID F.A.0
Extended CPUID 10.A
Core Stepping PH-E0
Technology 45 nm
TDP Limit 126 Watts
Core Speed 3300.0 MHz
Multiplier x FSB 16.5 x 200.0 MHz
HT Link speed 2000.0 MHz
Stock frequency 3300 MHz
Instructions sets MMX (+), 3DNow! (+), SSE, SSE2, SSE3, SSE4A, x86-64, AMD-V
L1 Data cache 6 x 64 KBytes, 2-way set associative, 64-byte line size
L1 Instruction cache 6 x 64 KBytes, 2-way set associative, 64-byte line size
L2 cache 6 x 512 KBytes, 16-way set associative, 64-byte line size
L3 cache 6 MBytes, 48-way set associative, 64-byte line size
FID/VID Control yes
Min FID 4.0x
P-State FID 0x15 - VID 0x06 - IDD 16 (18.50x - 1.475 V)
P-State FID 0x11 - VID 0x0E - IDD 16 (16.50x - 1.375 V)
P-State FID 0x9 - VID 0x12 - IDD 12 (12.50x - 1.325 V)
P-State FID 0x1 - VID 0x16 - IDD 9 (8.50x - 1.275 V)
P-State FID 0x100 - VID 0x1A - IDD 5 (4.00x - 1.225 V)

Package Type 0x1
Model 10
String 1 0x0
String 2 0x1
Page 0x0
CmpCap 6
ApicIdCoreSize 8
TDC Limit 96 Amps
Max non-turbo ratio 16.50x
Max turbo ratio 18.50x
Attached device PCI device at bus 0, device 24, function 0
Attached device PCI device at bus 0, device 24, function 1
Attached device PCI device at bus 0, device 24, function 2
Attached device PCI device at bus 0, device 24, function 3
Attached device PCI device at bus 0, device 24, function 4

OK. Your post suggests that you didn't touch any voltage settings. If this is true, then your stability can be increased by raising vcore, but first try this:

1. Raise the FSB until failure again
2. Set RAM to specs shown on the side sticker
3. Disable Cool n Quiet
4. Raise vcore by one level. Some BIOS allow you to press the "+" key; some require you to use the up/down arrows. Either way, just increase vcore by one level (key stroke) at a time.

If this doesn't help, there may be need for additional steps. You may need to adjust the Northbridge multiplier; you may even need to lower your RAM frequency.

Edit: To make this clearer, increase vcore one step at a time and test the OC settings in Windows. To test for stability, download, install, and run Prime95. Run this test on blend for about 1/2 hour.

Okay.
So This is where im at now:
3.885Mhz (3.8Ghz)
18.5 Multiplier
210 FSB
1.40v to the cpu

Should i keep pushing it??

raise vcore to 1.44-1.45 , you use X6 at 3.8Ghz ... try it and test use IBT for shortime just 30minutes and use Prime95 for Longtime 8hours minimal

You need to back up and stress test at a reasonable setting. Set it to 3.7 and then run prime95 until your temps level out or you crash. If you BSOD, up the voltage a bit and repeat the stress test. If it passes, up the frequency, test, repeat, etc.

I use 1055T can get 3.8ghz with vcore 1.44 , cpu nb 0.025, nb at 2800 he he very stong corevid1.32v, vdim at 1.58V .. I you can get 3.8gjz use 1.40 it's very very good

It worked!