Sign in with
Sign up | Sign in
Your question

Phenom II x6 1045t

Last response: in Overclocking
Share
March 14, 2012 11:12:00 PM

I have a phenom II x6 1045t i want to overclock I have played around without good results, I have been told that disabling 2 cores and overclocking is the best the cpu is in a gigabyte ga-m68mt-s2 am3+ mobo if anyone can help walk me thru some of this would be awesome

More about : phenom 1045t

a b À AMD
a b K Overclocking
March 15, 2012 1:12:49 AM

I have my 1045t OC'd to 3.4 Ghz with all 6 cores running. It could go higher but, I'm limited by heat because I can't fit a bigger cooler in my case.

I recommend getting some free software first. CPU-Z and HWmonitor, and prime95.

CPU-Z will show you frequencies, voltages and ram timings.

HWmonitor will show you temps. *Be warned* HWmonitor was showing my core temps 10 degrees lower than they actually were. The temp labeled "TMPIN2" was actually tracking perfectly with the core temps shown in AMD Overdive. So look for the highest temperature other than your video card. (many video cards can safely run at hotter temps than your CPU.) The hottest one on my Gigabyte 990 fxa ud3 (other than the video card) is the core temp. Try to keep it below 55C under full load.

Prime95 is the program that will stress test your computer to see if it can remain stable and cool under load. 2hrs of the blend test with no errors and no overheating is a general rule of thumb for a stable OC.

Now for the fun stuff.

Go into your BIOS and lower the multiples for your CPU and your Ram by a few steps. (The 1045t won't let you increase the multiplier above stock)
Then disable turbo (aka "core performance boost")
Then find your CPU Host clock control and set it to "manual"
Then You should be able to change the "CPU Frequency" (I'll call it FSB) (This is before the multiplier, so it will be low. Mine started at 200)
Now increase that variable by a bit.

I recommend balancing your FSB and your "memory clock" (RAM) multiplier to a point where your ram is back down to stock speeds after you bump the FSB. So raise your FSB to something like 250 then adjust your RAM multiplier down so that your RAM us running at or near stock speeds.

Now move on to your CPU clock ratio. With the faster FSB, you will be able to run your CPU at higher frequencies with a lower-than-stock multiplier. I eventually took mine all the way back up to 13.5 with a final frequency of 3.4 Ghz.

I would recommend starting with a lower multiple that gets you just a couple hundred Mhz boost over stock at first. Then test for stability and heat. Run prime 95 for at least 30 minutes if you want to see your hottest temps. The blend doesn't get things hot until about the third bank of tests.

If things look good, go back into the BIOS and bump the multiplier some more and re-test.

My MB got rather ambitious with the voltages when I left it in auto, so use CPU-Z to keep an eye on core voltages. Many recommend just staying under 1.45 volts. I recommend not going any higher than you need to for a given clock speed. This will help keep heat down. I ended up using a negative offset "CPU voltage control" of -0.075 volts. This brought my core voltages down to about 1.344v at full load.

*note* I'm scraping the floor on voltage with my particular chip/speed. One notch lower and I get BSOD. You may be able to go a little lower or you may need a little more voltage for your chip and clock speed.

Now just test and adjust and repeat.

Generally speaking:

BSOD means you need more voltage, and/or less speed.

Overheating means you need less voltage and/or less speed. (or a better cooler for your CPU.)

If you get to the point where your temps are good and your computer is sable, and you still want to go faster (than ~3.4Ghz), you can go back and bump up the FSB. But remember to adjust your RAM multiplier back down to stock-ish speeds.

You can OC your RAM later, but that gets a little more complicated as you may have to adjust CAS timings and RAM voltages to make it work. Keeping your RAM at stock speeds should give you one less thing to worry about while you probe the limits of your CPU.

Good luck!
March 15, 2012 1:44:20 AM

ok thanx first off for the detailed walkthru and the effort you put in to your response, I am gonna give it a crack again hopefully with more success this time I'll let ya know how it goes
Related resources
a b À AMD
a b K Overclocking
March 15, 2012 1:47:28 AM

I also forgot to mention that you should keep an eye on your HT link speed. (In CPU-Z)

I have heard that you want to keep it close to 2000 (or lower). My MB does it automatically up to about 250 FSB speed. Above that FSB speed you have to start bringing The HT back down like your RAM.
March 15, 2012 2:07:45 AM

ok well the only way I can find to adjust fsb is by using easytuner6 i don't think i can via bios the mob probably sux its a gigabytr ga-m68mt-s2 , either the options are not available in my bios or its just confusing me.....dunno what to try any suggestions maybe bios upgrade???? i dunno
a b À AMD
a b K Overclocking
March 15, 2012 12:20:12 PM

I just glanced at the manual for your MB and I can't find a FSB adjustment either. It's odd that they let you adjust the ram clock though.

The best you can do in the BIOS then will be to disable cool and quiet. That one modification made a bigger difference for my everyday computing than my OC.

With cool and quiet active, your CPU will down-clock as low as 800 Mhz and simple things like surfing the web will really drag.
March 15, 2012 4:16:08 PM

ok thanx for checking it out, maybe thats why the mobo driver disc came with easy tuner 6 I tried using it tho and it would just freeze most times
May 16, 2012 10:17:26 AM

i have the same cpu and mobo is a asrock n68-s3 but my mobo max wattage 95 and thts the same wattage as the cpu so if i want 2 oc i dont rasie my voltage plz rely
!