Sign in with
Sign up | Sign in
Your question

Configure ISA card in winxp

Last response: in Windows XP
Share
November 7, 2012 1:53:41 PM

I have P4BWA mother board recently bought it.

http://www.commell.com.tw/product/SBC/P4BWA.HTM

This card have 2 ISA slots.


We have one ISA slot card 16 bit working with windows 98.
The software DAAS32 with it is 32 bit.

one chinese site says it works with windows xp.
http://www.nju520.com/bbs/dv_rss.asp...d=10461&page=1

注意:因为原DAAS32不支持WindowsXP,如果在Windows XP下运行DAAS32,请用Windows98兼容模式。

Translation :
Note: because original DAAS32 not support WindowsXP, Windows98 compatibility mode if running under Windows XP DAAS32,.


The software works ok but the card is not recognized.
we think this card is not PNP.
So it has to be set manually.

The ISA card manual says :
The default setting in ISA slot card is 358h-35Fh

Address of Converter
Board Selects the address range of the DAASâ32 converter
board. The normal setting is address 358h-35Fh. If this
setting leads to address conflicts with other boards the
range can be changed by setting jumpers on the converter
board. If the jumper setting does not correspond with the
setting under this menu heading, the error message "No
answer from converter board..."appears.
The following address ranges are possible:
· 1D8h - 1DFh, Jumper setting: J1 . . J8 = 0 0 0 1 1 0 1 0
· 2D8h - 2DFh, Jumper setting: J1 . . J8 = 0 0 1 1 0 0 1 0
· 320h - 327h, Jumper setting: J1 . . J8 = 1 1 0 0 0 1 1 1
· 350h - 357h, Jumper setting: J1 . . J8 = 1 0 0 1 0 0 1 1
· 358h - 35Fh, Jumper setting: J1 . . J8 = 1 0 0 1 0 0 1 0

How to get this card configured?

waiting for help/guidance in the matter,
November 8, 2012 2:37:28 AM

Yes, I am running under win98 compatibility mode.

I will try as mentioned in the link you have suggested.

The ISA board normal setting is address 358h-35Fh
How to configure this?
m
0
l
Related resources
November 8, 2012 3:08:38 PM

mhtplsh said:
Yes, I am running under win98 compatibility mode.

I will try as mentioned in the link you have suggested.

The ISA board normal setting is address 358h-35Fh
How to configure this?


Should be able to in the last step of the link instructions.
m
0
l
November 10, 2012 6:52:16 AM

hang-the-9 said:
Should be able to in the last step of the link instructions.


I tried to do as mentioned in the link & your instructions.
But windows xp don't allow us to add address required for my ISA card.
The following address ranges are possible:
· 1D8h - 1DFh, Jumper setting: J1 . . J8 = 0 0 0 1 1 0 1 0
· 2D8h - 2DFh, Jumper setting: J1 . . J8 = 0 0 1 1 0 0 1 0
· 320h - 327h, Jumper setting: J1 . . J8 = 1 1 0 0 0 1 1 1
· 350h - 357h, Jumper setting: J1 . . J8 = 1 0 0 1 0 0 1 1
· 358h - 35Fh, Jumper setting: J1 . . J8 = 1 0 0 1 0 0 1 0

But instead xp suggest some other address.
My addresses are shown as invalid.


Guide me further.
m
0
l
November 12, 2012 12:59:42 PM

mhtplsh said:
I tried to do as mentioned in the link & your instructions.
But windows xp don't allow us to add address required for my ISA card.
The following address ranges are possible:
· 1D8h - 1DFh, Jumper setting: J1 . . J8 = 0 0 0 1 1 0 1 0
· 2D8h - 2DFh, Jumper setting: J1 . . J8 = 0 0 1 1 0 0 1 0
· 320h - 327h, Jumper setting: J1 . . J8 = 1 1 0 0 0 1 1 1
· 350h - 357h, Jumper setting: J1 . . J8 = 1 0 0 1 0 0 1 1
· 358h - 35Fh, Jumper setting: J1 . . J8 = 1 0 0 1 0 0 1 0

But instead xp suggest some other address.
My addresses are shown as invalid.


Guide me further.


Your card may not work under XP, did you check with the vendor?
m
0
l
November 14, 2012 6:44:46 AM

hang-the-9 said:
Your card may not work under XP, did you check with the vendor?


Thanks hang-the-9.
The vendor hv new pci/usb models for winxp.
So he is not ready to help or the card might not work for xp as u say.
m
0
l
November 24, 2012 2:59:54 AM

mhtplsh said:
I have P4BWA mother board recently bought it.

http://www.commell.com.tw/product/SBC/P4BWA.HTM

This card have 2 ISA slots.


We have one ISA slot card 16 bit working with windows 98.
The software DAAS32 with it is 32 bit.

one chinese site says it works with windows xp.
http://www.nju520.com/bbs/dv_rss.asp...d=10461&page=1

注意:因为原DAAS32不支持WindowsXP,如果在Windows XP下运行DAAS32,请用Windows98兼容模式。

Translation :
Note: because original DAAS32 not support WindowsXP, Windows98 compatibility mode if running under Windows XP DAAS32,.


The software works ok but the card is not recognized.
we think this card is not PNP.
So it has to be set manually.

The ISA card manual says :
The default setting in ISA slot card is 358h-35Fh

Address of Converter
Board Selects the address range of the DAASâ32 converter
board. The normal setting is address 358h-35Fh. If this
setting leads to address conflicts with other boards the
range can be changed by setting jumpers on the converter
board. If the jumper setting does not correspond with the
setting under this menu heading, the error message "No
answer from converter board..."appears.
The following address ranges are possible:
· 1D8h - 1DFh, Jumper setting: J1 . . J8 = 0 0 0 1 1 0 1 0
· 2D8h - 2DFh, Jumper setting: J1 . . J8 = 0 0 1 1 0 0 1 0
· 320h - 327h, Jumper setting: J1 . . J8 = 1 1 0 0 0 1 1 1
· 350h - 357h, Jumper setting: J1 . . J8 = 1 0 0 1 0 0 1 1
· 358h - 35Fh, Jumper setting: J1 . . J8 = 1 0 0 1 0 0 1 0

How to get this card configured?

waiting for help/guidance in the matter,

never heard of it, floppy disc yes but no ISA, could be miss read ssd maybe
m
0
l
!