Closed Solved

Frustrating problems with motherboard turning on and off

Hi, I'm building my first computer and having a problem. I have a GIGABYTE motherboard and installed an intell CPU with a fan on it as well as 4 ram sticks. Also have a 600w power supply hooked up to it and connected all the cables from the case to the motherboard. I would tell you the beeps but the Antec 300 does not have a speaker built in.
When I went to do the first test all the LED lights came on to signal that the cables were plugged in properly and the CPU fan came on as well as the power supply fan but they quickly turned off, then they repeat this same cycle of turning on and off each time. I was grounded when I built it, no static. No idea what is going on, have been trying to figure out the problem for the past hour. Have reinstalled everything on the motherboard to make sure that they are connected correctly including the RAM, CPU and power supplies.

Frustrated that five hours of work has gone to waste :/ Can anyone help?
6 answers Last reply Best Answer
More about frustrating problems motherboard turning
  1. Best answer
    Work through our standard checklist and troubleshooting thread:
    I mean work through, not just read over it. We spent a lot of time on this. It should find most of the problems.

    If not, continue.

    I have tested the following beeps patterns on Gigabyte, eVGA, and ECS motherboards. Other BIOS' may be different.

    Breadboard - that will help isolate any kind of case problem you might have.

    Breadboard with just motherboard, CPU & HSF, case speaker, and PSU. You do have a case speaker installed, right? If not, you really, really need one. If your case or motherboard didn't come with a system speaker, you can buy one here:

    You can turn on the PC by momentarily shorting the two pins that the case power switch goes to. You should hear a series of long, single beeps indicating memory problems. Silence indicates a problem with (in most likely order) the PSU, motherboard, or CPU.

    Motherboard LED's mean very little. When on, all they are telling you is that the computer os plugged into a live power socket and the PSU is switched.

    Remember, at this time, you do not have a graphics card installed so the load on your PSU will be reduced.

    If no beeps:
    At this point, you can sort of check the PSU. Try to borrow a known good PSU of around 550 - 600 watts. That will power just about any system with a single GPU. If you cannot do that, use a DMM to measure the voltages. Measure between the colored wires and either chassis ground or the black wires. Yellow wires should be 12 volts. Red wires: +5 volts, orange wires: +3.3 volts, blue wire : -12 volts, violet wire: 5 volts always on. Tolerances are +/- 5% except for the -12 volts which is +/- 10%.

    The gray wire is really important. It should go from 0 to +5 volts when you turn the PSU on with the case switch. CPU needs this signal to boot.

    You can turn on the PSU by completely disconnecting the PSU and using a paperclip or jumper wire to short the green wire to one of the neighboring black wires.

    This checks the PSU under no load conditions, so it is not completely reliable. But if it can not pass this, it is dead. Then repeat the checks with the PSU plugged into the computer to put a load on the PSU.

    If the system beeps:
    If it looks like the PSU is good, install a memory stick. Boot. Beep pattern should change to one long and several short beeps indicating a missing graphics card. Silence or long single beeps indicate a problem with the memory.

    Insert the video card and connect any necessary PCIe power connectors. Boot. At this point, the system should POST successfully (a single short beep). Notice that you do not need keyboard, mouse, monitor, or drives to successfully POST.

    Now start connecting the rest of the devices starting with the monitor, then keyboard and mouse, then the rest of the devices, testing after each step.

    It's possible that you can pass the POST with a defective video card. The POST routines can only check the video interface. It cannot check the internal parts of the video card.
  2. I got it to work! I am so happy! Thank you so much! Most common new user mistake=my mistake
  3. Yeah, you didn't plug in the 4/8-pin connector?

    C'mon now . . . tell us which mistake . . . pretty please?

    Seriously, it could help us help the next guy.
  4. yeah the CPU power plug, it didn't specify to plug it in, in my handbook that I was using. Very odd that it didn't! But oh well, It's definitely up and running now.
  5. Best answer selected by emilaweb.
  6. This topic has been closed by Maziar
Ask a new question

Read More

Motherboards Power Supplies