Sign in with
Sign up | Sign in
Your question

Getting a BIOS error when system wakes up from windows sleep

Last response: in Systems
Share
September 6, 2010 5:18:22 PM

I built a new system recently and everything is working great except when windows 7 sleeps and wakes up.
I am getting this error in BIOS when the system wakes from windows 7 sleep.

"System has experience boot failures because of overclocking..."

and asks me to press any key for continuing or del to enter bios. If I press any key it continues and to resume windows and everything works fine. I have not overclocked or done any modifications

System Config:
AMD Phenom(tm) II X4 965 Processor- BE
GA-880GMA-UD2H
Seagate 1TB HDD
G.Skill 2GB *2 RAM





Memory SPD
-------------------------------------------------------------------------

DIMM # 1
SMBus address 0x50
Memory type DDR3
Module format UDIMM
Manufacturer (ID) G.Skill (7F7F7F7FCD000000)
Size 2048 MBytes
Max bandwidth PC3-10700 (667 MHz)
Part number F3-12800CL9-2GBRL
Number of banks 8
Nominal Voltage 1.50 Volts
EPP no
XMP yes
XMP revision 0.0
JEDEC timings table CL-tRCD-tRP-tRAS-tRC @ frequency
JEDEC #1 6.0-6-6-17-23 @ 457 MHz
JEDEC #2 7.0-7-7-20-27 @ 533 MHz
JEDEC #3 8.0-8-8-22-31 @ 609 MHz
JEDEC #4 9.0-9-9-25-34 @ 685 MHz
XMP profile XMP-1600
Specification PC3-12800
Voltage level 1.500 Volts
Min Cycle time 1.250 ns (800 MHz)
Min tRP 11.00 ns
Min tRCD 11.00 ns
Min tWR 15.00 ns
Min tRAS 30.00 ns
Min tRC 49.00 ns
Min tRFC 110.00 ns
Min tRTP 7.50 ns
Min tRRD 6.00 ns
Command Rate 2T
XMP timings table CL-tRCD-tRP-tRAS-tRC-CR @ frequency (voltage)
XMP #1 9.0-9-9-25-41-2T @ 818 MHz (1.500 Volts)

DIMM # 2
SMBus address 0x51
Memory type DDR3
Module format UDIMM
Manufacturer (ID) G.Skill (7F7F7F7FCD000000)
Size 2048 MBytes
Max bandwidth PC3-10700 (667 MHz)
Part number F3-12800CL9-2GBRL
Number of banks 8
Nominal Voltage 1.50 Volts
EPP no
XMP yes
XMP revision 0.0
JEDEC timings table CL-tRCD-tRP-tRAS-tRC @ frequency
JEDEC #1 6.0-6-6-17-23 @ 457 MHz
JEDEC #2 7.0-7-7-20-27 @ 533 MHz
JEDEC #3 8.0-8-8-22-31 @ 609 MHz
JEDEC #4 9.0-9-9-25-34 @ 685 MHz
XMP profile XMP-1600
Specification PC3-12800
Voltage level 1.500 Volts
Min Cycle time 1.250 ns (800 MHz)
Min tRP 11.00 ns
Min tRCD 11.00 ns
Min tWR 15.00 ns
Min tRAS 30.00 ns
Min tRC 49.00 ns
Min tRFC 110.00 ns
Min tRTP 7.50 ns
Min tRRD 6.00 ns
Command Rate 2T
XMP timings table CL-tRCD-tRP-tRAS-tRC-CR @ frequency (voltage)
XMP #1 9.0-9-9-25-41-2T @ 818 MHz (1.500 Volts)
a c 104 B Homebuilt system
a b $ Windows 7
September 6, 2010 5:24:40 PM

I had a similar issue with an Asus board ones. It had a auto setting in bios for overclocking and I resolved it by setting it to manual.
m
0
l
September 13, 2010 5:00:19 AM

Sorry for the late reply I have the gigabyte motherboard, which specific setting are u referring to I was not able to find a overclocking setting that was enabled.
m
0
l
Related resources
a c 104 B Homebuilt system
a b $ Windows 7
September 13, 2010 11:25:33 PM

I have a AM2+ board from Gigabyte and in BIOS there is MB intelligent tweaker (MIT) it has overclocking options on AUTO. I resolved my ASUS issue in similar settings by putting it on manual retaining stock settings for the affected hardware.
m
0
l
September 16, 2010 8:07:00 AM

In my bios-MIT I do not se any option for overclocking but I see an option called "CPU clock ratio" set to "auto" and I assume for my processor it should be set to 17 (Phenom II 965 is 3400mhz = 17 * 200mhz) I assume.
m
0
l
April 26, 2011 9:55:24 PM

i'm curious... did that fix it? cuz i have the same issue
m
0
l
!