Sign in with
Sign up | Sign in
Your question
Solved

Hyper Transfer Sync Error -Drivers

Tags:
  • Motherboards
  • Drivers
  • Graphics Cards
  • Windows XP
  • Product
Last response: in Motherboards
Share
August 20, 2011 2:14:26 PM

Ok so I posted a previous thread in the XP forums when I thought it was XP or my GFX card. I have Win7 ultimate x86 installed right now and eveyrthing works fine.... Until I go to install drivers for audio or graphics card. Right now my graphics card shows in Device Manager but it is listed as 'Standard VGA Graphics Adapter'. I even install the ATI video driver off the Biostar utility cd and I get the same error. 'Hyper Transfer Flood Sync Error'. I've tried all versions of the catalyst software and all of them give me the same error. People all suggest this is a faulty RAM problem but it can't be. My system is stable without drivers installed...

Any suggestions?

More about : hyper transfer sync error drivers

a c 717 V Motherboard
a b \ Driver
a b U Graphics card
August 20, 2011 3:45:58 PM

That error can be caused by a variety of problems: MOBO, RAM, PSU, OC, BIOS, etc. First observation - don't use the CD; go to Biostar and download the NEWER drivers from their website.

Need to know your full specs (CPU, MOBO, GPU, PSU. RAM, and BIOS version); CPU-z can help identify -> http://www.cpuid.com/softwares/cpu-z.html

Otherwise my feeling are your MOBO, PSU or GPU. When the GPU drivers are running properly it draws additional power so the additional load is causing an error; similarly a bad GPU can also trigger a similar problem. Voltage drops and 'poof' you get the errors. **So try a different PSU from another PC **

You might want to look at the Event Manager and see what Critical errors are listed and what's the root cause(s); see http://i1013.photobucket.com/albums/af254/Jaquith/Event...
m
0
l
August 20, 2011 4:53:36 PM

Sorry I can't believe I forgot my system specs...

biostar A880G micro ATX
radeon hd 4770
Phenom II X6 1090T @ 3.2
4GB g.Skill DDR3 @ 1600

I got everything working fine by moving the 4 gig stick into the second slot again and drivers were installed, graphics card was working. Then I tried getting my second 4 gig stick in there and everything went to *** again. Back in the same loop. Even with 1 stick in the second card again it still fails.

When I first got it working I changed the hyper transport settings in BIOS to 1ghz and 16 bit. Its what got me up and running but now it doesn't even matter it is still toast.

I'm starting to think that it is a PSU issue as I've had it for a while and instead of 5v and 12v at startup I have 4.875 and 11.9. Is this normal?
m
0
l
Related resources
August 20, 2011 5:14:37 PM

I also got this upon returning to windows without video drivers...


Problem signature:
Problem Event Name: BlueScreen
OS Version: 6.1.7601.2.1.0.256.1
Locale ID: 1033

Additional information about the problem:
BCCode: 124
BCP1: 0000000000000000
BCP2: FFFFFA80049378F8
BCP3: 0000000000000000
BCP4: 0000000000000000
OS Version: 6_1_7601
Service Pack: 1_0
Product: 256_1

Files that help describe the problem:
C:\Windows\Minidump\082011-27736-01.dmp
C:\Users\Jeff\AppData\Local\Temp\WER-37299-0.sysdata.xml


I ran CPU-Z and of course all it could find was my processor information. No info on board or RAM....
m
0
l
a c 717 V Motherboard
a b \ Driver
a b U Graphics card
August 20, 2011 5:46:40 PM

Common BSOD Errors:
BSOD Error codes and what they mean:
0X00000050 << Incorrect Memory Timing/Freq or Uncore Multi
0X00000124 << Incorrect QPI/Vtt Voltage (To Much/Not Enough)
0X00000101 << Not enough Vcore Voltage

Manually set ALL RAM Values in the BIOS, first try DRAM Frequency -> DDR3 1333MHz.

If you post your exact set of RAM I can post the correct settings and check compatibility. "4GB g.Skill DDR3 @ 1600" narrows it down to A LOT of possibilities.

1. RAM - provide link to Set.
2. What BIOS version? See CPU-z Mainboard
m
0
l
August 20, 2011 6:40:45 PM

As I said before CPU-z is bringing up nothing for the mainboard or memory.

Those BSOD codes mean a lot though because I just noticed that my A880G+ board only supports up tho DDR3 1333MHz. Setting my bios down to 1333 will probably work! I'm not sure if i can find the settings to change that though. Will report back soon.

Thanks a lot for your help
m
0
l
August 20, 2011 7:46:08 PM

Changed the ram to 1333MHz to no avail. Still only runs with onboard graphics. Everything runs fine with gfx card if I am in safe mode but normal windows just keeps getting hyper sync flood error.... I am so confused!
m
0
l
August 20, 2011 9:16:06 PM

So CPU-Z is working for me now... this is what it came up with...

How do I get my FSB : DRAM ratio back down from 3:10... every time im in the bios FSB is locked at 200MHz









m
0
l
a c 717 V Motherboard
a b \ Driver
a b U Graphics card
August 20, 2011 9:34:21 PM

You need to post your exact MOBO, "As I said before" there are several versions of your 'A880G'.

So me picking one and posting settings might not pertain. In general you need to set the BIOS to allow Manual Overclocking then the FSB settings will show-up. It seems the only setting you did was to set the DRAM Frequency -> DDR3-1333MHz and not the CAS Timings...
m
0
l
August 20, 2011 10:06:27 PM

Ok... Well I upped the FSB from 200 to 220. Things are running now with drivers installed!

System crashed once but I have been stable for 30 minutes ( no processes really running)

I thought the screenshot from CPU-Z told you the MOBO info but I guess not.

http://www.newegg.com/Product/Product.aspx?Item=N82E168...

I still need help making my system more stable and getting my FSB: DRAM ratio in check.

I have CPU freq at 220Mhz, RAM timings are at 9-9-9-24, RAM voltage 1.5v, NB voltage is at 1.2

thanks for all your help im getting closer!



System crashed once already but no errors and can boot back up. Just looking for more stable settings. Will be back in a minute with BIOS version.
m
0
l

Best solution

a c 717 V Motherboard
a b \ Driver
a b U Graphics card
August 20, 2011 10:46:23 PM

There were (2) G+.

Good Luck! :) 
Share
August 20, 2011 11:10:25 PM

What do you mean 2 G+?

Also, everything runs fine but I have a clean install of windows... As soon as I run Prime95 it crashes and I still have the ratio of 3:10.

No matter what settings I change cpu-z says I have that ratio....
m
0
l
August 21, 2011 1:16:33 AM

Hopefully I get help with the last part. Anyhoot,,, jaquith PM me your paypal I'll buy you lunch tomorrow.
m
0
l
August 31, 2011 5:50:14 PM

This ended up being a RAM issue after all (I think)

I took one stick out and am running with just 1 stick fine on many different OC settings. Weird how one day it doesn't like my RAM. Hah
m
0
l
September 5, 2011 11:20:45 AM

Found a solution to the problem... Was only getting hung up when playing Bad Compnay 2... Found a thread somewhere else here stating that you should turn off all monitoring programs before playing. msi AB was running all the time, turned that off, and no hyper transfer errors anymore! wow!
m
0
l
September 10, 2011 1:29:47 PM

Best answer selected by pcenvy88.
m
0
l
!