New PC Build - System will not turn on

bravo99

Distinguished
Aug 31, 2011
3
0
18,510
Hello,

I just built a new PC and when I plugged it in and turned it on, the power led light on the motherboard came on, but when I turn on the power switch on the front of the PC, absolutely nothing happens. No lights, no fans, nothing. I tried all of the various power switches (front of tower, back of power supply) and nothing happens. I also tried jumping the two pins on the motherboard for the power switch with a screwdriver to see if the front switch is bad... still nothing. Any suggestions?

ASUS P8Z68-V motherboard
Intel i5 2400 processor
Using on board graphics
12 MB Corsair Vengeance DDR3 1600 memory
COOLER MASTER Elite 430 RC-430-KWN1 Case
Antec 430W power supply

Thanks!
 
Solution
Work systematically through our standard checklist and troubleshooting thread:
http://www.tomshardware.com/forum/261145-31-read-posting-boot-problems
I mean work through, not just read over it. We spent a lot of time on this. It should find most of the problems.

If no luck, continue.

The following is an expansion of my troubleshooting tips in the breadboarding link in the "Cannot boot" thread.

I have tested the following beep patterns on Gigabyte, eVGA, and ECS motherboards. Other BIOS' may be different, but they all use a single short beep for a successful POST.

Breadboard - that will help isolate any kind of case problem you might have.
http://www.tomshardware.com/forum/262730-31-breadboarding

Breadboard with...

thaman9764

Distinguished
Aug 10, 2011
1
0
18,510


did u make sure the terminals are correct?
 
Work systematically through our standard checklist and troubleshooting thread:
http://www.tomshardware.com/forum/261145-31-read-posting-boot-problems
I mean work through, not just read over it. We spent a lot of time on this. It should find most of the problems.

If no luck, continue.

The following is an expansion of my troubleshooting tips in the breadboarding link in the "Cannot boot" thread.

I have tested the following beep patterns on Gigabyte, eVGA, and ECS motherboards. Other BIOS' may be different, but they all use a single short beep for a successful POST.

Breadboard - that will help isolate any kind of case problem you might have.
http://www.tomshardware.com/forum/262730-31-breadboarding

Breadboard with just motherboard, CPU & HSF, case speaker, and PSU.

Make sure you plug the CPU power cable in. The system will not boot without it.

I always breadboard a new build. It takes only a few minutes, and you know you are putting good parts in the case once you are finished.

You can turn on the PC by momentarily shorting the two pins that the case power switch goes to. You should hear a series of long, single beeps indicating memory problems. Silence indicates a problem with (in most likely order) the PSU, motherboard, or CPU. Remember, at this time, you do not have a graphics card installed so the load on your PSU will be reduced.

If no beeps:
Running fans and drives and motherboard LED's do not necessarily indicate a good PSU. In the absence of a single short beep, they also do not indicate that the system is booting.

At this point, you can sort of check the PSU. Try to borrow a known good PSU of around 550 - 600 watts. That will power just about any system with a single GPU. If you cannot do that, use a DMM to measure the voltages. Measure between the colored wires and either chassis ground or the black wires. Yellow wires should be 12 volts. Red wires: +5 volts, orange wires: +3.3 volts, blue wire : -12 volts, violet wire (standby power supply): 5 volts always on. Tolerances are +/- 5% except for the -12 volts which is +/- 10%.

The gray wire is really important. It should go from 0 to +5 volts when you turn the PSU on with the case switch. CPU needs this signal to boot.

You can turn on the PSU by completely disconnecting the PSU and using a paperclip or jumper wire to short the green wire to one of the neighboring black wires.
http://www.youtube.com/watch?v=5FWXgQSokF4&feature=youtube_gdata

A way that might be easier is to use the main power plug. Working from the back of the plug where the wires come out, use a bare paperclip to short between the green wire and one of the neighboring black wires. That will do the same thing with an installed PSU. It is also an easy way to bypass a questionable case power switch.

This checks the PSU under no load conditions, so it is not completely reliable. But if it can not pass this, it is dead. Then repeat the checks with the PSU plugged into the computer to put a load on the PSU.

If the system beeps:
If it looks like the PSU is good, install a memory stick. Boot. Beep pattern should change to one long and several short beeps indicating a missing graphics card. This should not happen if you have built in graphics

Silence, long single beeps, or series of short beeps indicate a problem with the memory. If you get short beeps verify that the memory is in the appropriate motherboard slots.

Insert the video card and connect any necessary PCIe power connectors. Boot. At this point, the system should POST successfully (a single short beep). Notice that you do not need keyboard, mouse, monitor, or drives to successfully POST.
At this point, if the system doesn't work, it's either the video card or an inadequate PSU. Or rarely - the motherboard's PCIe interface.

Now start connecting the rest of the devices starting with the monitor, then keyboard and mouse, then the rest of the devices, testing after each step. It's possible that you can pass the POST with a defective video card. The POST routines can only check the video interface. It cannot check the internal parts of the video card.

 
Solution

bravo99

Distinguished
Aug 31, 2011
3
0
18,510
OK,

I switched the power connector from the 2x6 power connector to the 2x4 (sorry if these are the wrong terms) and it powered up like a champ. I guess the 2x6 connector would normally go to a video card? Since I am using on board video, I do not have it connected to anything.

Thanks for the quick replies.