Computer won't start

My computer wont start and i can see that the power isn't being supplied to anything but the power source on my recently modified gateway computer and the power source is clicking and the light on the back is blinking, the fan is occasionally moving, and the power and hdd lights on the front are flashing. any help would be appreciated, i have disassembled it and fixed many hardware position and connection errors (all that i could see). the dvd drive won't light up or eject and my monitor says no signal RGB.
8 answers Last reply Best Answer
More about computer start
  1. Sounds like your power supply isn't working right. You mentioned the fan isn't always moving also. I would try another PSU and see if that fixes it.
  2. What are the system specs of the original parts and the parts you added?

    Time to start troubleshooting.

    Work through our standard checklist and troubleshooting thread:
    I mean work through, not just read over it. We spent a lot of time on this. It should find most of the problems.

    If not, continue.

    I have tested the following beeps patterns on Gigabyte, eVGA, and ECS motherboards. Other BIOS' may be different.

    Breadboard - that will help isolate any kind of case problem you might have.

    Breadboard with just motherboard, CPU & HSF, case speaker, and PSU. You do have a case speaker installed, right? If not, you really, really need one. If your case or motherboard didn't come with a system speaker, you can buy one here:

    You can turn on the PC by momentarily shorting the two pins that the case power switch goes to. You should hear a series of long, single beeps indicating memory problems. Silence indicates a problem with (in most likely order) the PSU, motherboard, or CPU.

    Motherboard LED's mean very little. When on, all they are telling you is that the computer os plugged into a live power socket and the PSU is switched.

    Remember, at this time, you do not have a graphics card installed so the load on your PSU will be reduced.

    If no beeps:
    At this point, you can sort of check the PSU. Try to borrow a known good PSU of around 550 - 600 watts. That will power just about any system with a single GPU. If you cannot do that, use a DMM to measure the voltages. Measure between the colored wires and either chassis ground or the black wires. Yellow wires should be 12 volts. Red wires: +5 volts, orange wires: +3.3 volts, blue wire : -12 volts, violet wire: 5 volts always on. Tolerances are +/- 5% except for the -12 volts which is +/- 10%.

    The gray wire is really important. It should go from 0 to +5 volts when you turn the PSU on with the case switch. CPU needs this signal to boot.

    You can turn on the PSU by completely disconnecting the PSU and using a paperclip or jumper wire to short the green wire to one of the neighboring black wires.

    This checks the PSU under no load conditions, so it is not completely reliable. But if it can not pass this, it is dead. Then repeat the checks with the PSU plugged into the computer to put a load on the PSU.

    If the system beeps:
    If it looks like the PSU is good, install a memory stick. Boot. Beep pattern should change to one long and several short beeps indicating a missing graphics card. Silence or long single beeps indicate a problem with the memory.

    Insert the video card and connect any necessary PCIe power connectors. Boot. At this point, the system should POST successfully (a single short beep). Notice that you do not need keyboard, mouse, monitor, or drives to successfully POST.

    Now start connecting the rest of the devices starting with the monitor, then keyboard and mouse, then the rest of the devices, testing after each step. It's possible that you can pass the POST with a defective video card.

    The POST routines can only check the video interface. It cannot check the internal parts of the video card.
  3. there are no beeps at all just clicking and the powersupply is blicking, i moved all the hardware except the powersupply and motherboard to my dell opteron and it all works now
  4. Best answer
    i moved all the hardware except the powersupply
    The PSU is the culprit - the clicking sound is an internal spark generated from a spark...I'm just hoping the mobo wasn't shot down cos of the faulty PSU.

    The PSU blinking means there's a flux in power input/output and the PSU is having trouble managing it. I'm surprised how you didn't see a fire break out.
  5. omg so the mobo still works? and thnx now i know to change the power supply
  6. BTW, you didn't mention the PSU in question?
  7. Best answer selected by dsammcdermott.
  8. oh well, i got BA, disregard my question :D
Ask a new question

Read More

Prebuilt Light Computer Power Source Systems