Sign in with
Sign up | Sign in
Your question

No output from computer

Last response: in Systems
November 30, 2010 10:59:35 AM

My co-worker has a huge problem with his computer. Long story short, he purchased a gaming computer from a friend and played it for about 50 hours total with all the plastic still around the case. So my best guess is something overheated. He states that when he turns his computer on after a few seconds he will here the beep. However there is absolutely no output from his video card.

I have tried a different video card, still nothing. Tried removing and re-installing his RAM still nothing. I also tried a different hdmi cable and dvi-d cable still nothing. I have not tried to do anything to his motherboard or processor because I fell it might not be the problem. Just looking for maybe some ideas on what to check or do next?

Thank You

More about : output computer

a b B Homebuilt system
a b U Graphics card
November 30, 2010 11:27:11 AM

Keep digging... Try different memory and video card next. Then look for a power supply and CPU to continue testing with. If the BIOS has a jumper reset you may try that as well...
a c 122 B Homebuilt system
a b U Graphics card
November 30, 2010 1:23:22 PM

Work through our standard checklist and troubleshooting thread:
I mean work through, not just read over it. We spent a lot of time on this. It should find most of the problems.

If not, continue.

I have tested the following beeps patterns on Gigabyte, eVGA, and ECS motherboards. Other BIOS' may be different.

Breadboard - that will help isolate any kind of case problem you might have.

Breadboard with just motherboard, CPU & HSF, case speaker, and PSU. You do have a case speaker installed, right? If not, you really, really need one. If your case or motherboard didn't come with a system speaker, you can buy one here:

You can turn on the PC by momentarily shorting the two pins that the case power switch goes to. You should hear a series of long, single beeps indicating memory problems. Silence indicates a problem with (in most likely order) the PSU, motherboard, or CPU.

Motherboard LED's mean very little. When on, all they are telling you is that the computer os plugged into a live power socket and the PSU is switched.

Remember, at this time, you do not have a graphics card installed so the load on your PSU will be reduced.

If no beeps:
At this point, you can sort of check the PSU. Try to borrow a known good PSU of around 550 - 600 watts. That will power just about any system with a single GPU. If you cannot do that, use a DMM to measure the voltages. Measure between the colored wires and either chassis ground or the black wires. Yellow wires should be 12 volts. Red wires: +5 volts, orange wires: +3.3 volts, blue wire : -12 volts, violet wire: 5 volts always on. Tolerances are +/- 5% except for the -12 volts which is +/- 10%.

The gray wire is really important. It should go from 0 to +5 volts when you turn the PSU on with the case switch. CPU needs this signal to boot.

You can turn on the PSU by completely disconnecting the PSU and using a paperclip or jumper wire to short the green wire to one of the neighboring black wires.

This checks the PSU under no load conditions, so it is not completely reliable. But if it can not pass this, it is dead. Then repeat the checks with the PSU plugged into the computer to put a load on the PSU.

If the system beeps:
If it looks like the PSU is good, install a memory stick. Boot. Beep pattern should change to one long and several short beeps indicating a missing graphics card. Silence or long single beeps indicate a problem with the memory.

Insert the video card and connect any necessary PCIe power connectors. Boot. At this point, the system should POST successfully (a single short beep). Notice that you do not need keyboard, mouse, monitor, or drives to successfully POST.

Now start connecting the rest of the devices starting with the monitor, then keyboard and mouse, then the rest of the devices, testing after each step. It's possible that you can pass the POST with a defective video card.

The POST routines can only check the video interface. It cannot check the internal parts of the video card.