I posted this in video cards, but after a few days of research, I've determined it might be a motherboard issue:
I had my computer shipped across the country and when I received it today I discovered that it won't send a video signal to my monitor. Everything seems to be powering up normally on the motherboard, but my monitors aren't getting a signal from the computer. I wish I could tell you more, but because I can't interact with my OS or bios menus, I have no idea what is going on. I'm not even getting a bios splash when I power the comp up.
The computer had been working normally for weeks while it was hooked up to my brother's television. I had it hooked up via hdmi to the TV. I have tried every possible connection to get it working again: different monitors, different cables, and different connection types. But still, when I turn it on, nothing. I don't have the original TV it was hooked up to anymore. And It's likely not a resolution issue because the resolution of all the monitors (including the one it last worked on) was 1920x1080.
I have tried connecting it by hdmi and dvi to two different monitors and another television. I can't boot into safe mode because I can't get a display. I have also observed that my usb keyboard isn't lighting up. I removed the cmos battery to see if I could get something by clearing the bios and still nothing. I've taken half of it apart already and that didn't help (gpu, ram, and unplugged and replugged all the connections). I also tried putting the gpu in a different PCIe slot. Obviously it didn't work.
CORE I7 930 2.80G
ASUS P6T 1366 X58
2Gx3 - OCZ OCZ3G1600LV6GK
850w Power supply
Breadboard with just motherboard, CPU & HSF, case speaker, and PSU. Breadboard with just motherboard, CPU & HSF, case speaker, and PSU. At this point, if you do not have a system (internal case) speaker, you really need one.
Make sure you plug the CPU power cable in. The system will not boot without it.
I always breadboard a new build. It takes only a few minutes, and you know you are putting good parts in the case once you are finished.
You can turn on the PC by momentarily shorting the two pins that the case power switch goes to. You should hear a series of long, single beeps indicating memory problems. Silence indicates a problem with (in most likely order) the PSU, motherboard, or CPU. Remember, at this time, you do not have a graphics card installed so the load on your PSU will be reduced.
If no beeps, LED's, or fan activity:
Check for line power at the PSU input. Extension cords, power strips, and power cords do fail.
If you have power and no beeps, suspect components in likely order are PSU, motherboard, and CPU.
Running fans and drives and motherboard LED's do not necessarily indicate a good PSU. In the absence of a single short beep, they also do not indicate that the system is booting.
At this point, you can sort of check the PSU. Try to borrow a known good PSU of around 550 - 600 watts. That will power just about any system with a single GPU. If you cannot do that, use a DMM to measure the voltages. Measure between the colored wires and either chassis ground or the black wires. Yellow wires should be 12 volts. Red wires: +5 volts, orange wires: +3.3 volts, blue wire : -12 volts, violet wire: 5 volts always on. Tolerances are +/- 5% except for the -12 volts which is +/- 10%.
The gray wire is really important. It should go from 0 to +5 volts when you turn the PSU on with the case switch. CPU needs this signal to boot.
A way that might be easier is to use the main power plug. Working from the back of the plug where the wires come out, use a bare paperclip to short between the green wire and one of the neighboring black wires. That will do the same thing with an installed PSU. It is also an easy way to bypass a questionable case power switch.
This checks the PSU under no load conditions, so it is not completely reliable. But if it can not pass this, it is dead. Then repeat the checks with the PSU plugged into the computer to put a load on the PSU.
If the system beeps:
If it looks like the PSU is good, install a memory stick. Boot. Beep pattern should change to one long and several short beeps indicating a missing graphics card.
Silence, long single beeps, or series of short beeps indicate a problem with the memory. If you get short beeps verify that the memory is in the appropriate motherboard slots.
Insert the video card and connect any necessary PCIe power connectors. Boot. At this point, the system should POST successfully (a single short beep). Notice that you do not need keyboard, mouse, monitor, or drives to successfully POST. At this point, if the system doesn't work, it's either the video card or an inadequate PSU. Or rarely - the motherboard's PCIe interface.
Now start connecting the rest of the devices starting with the monitor, then keyboard and mouse, then the rest of the devices, testing after each step. It's possible that you can pass the POST with a defective video card. The POST routines can only check the video interface. It cannot check the internal parts of the video card.