Sign in with
Sign up | Sign in
Your question

I am trying to go from 32 bit Vista to 64 bit Windows 7.

Last response: in Windows 7
Share
May 6, 2012 6:18:35 PM

I am trying to go from 32 bit Vista to 64 bit Windows 7.

The 32 bit Vista was installed by mistake. My system can handle a 64 bit OS. Now I have finally found the time to upgrade. But the 64 bit intallation DVD can't be read from my OS. Any Advice?

I have tried setting up my CMOS so that I can boot from the DVD but I have run into some issues. First of all, when I look at my keyboard during the boot procedure, I noticed that the little light which indicates that one row of buttons are to be used for F1 - F12 keys, the little green led light goes on and off. Sometimes, during the boot process, it is on, sometimes it is off.

The CMOS procedure tells me I can hit F12 and set the boot order. I can hit F12 but when I go into that menu, I notice my keyboard is dead. The CPU does not accept any commands from me. So I need to power off and power on and try again.

The CMOS procedure tells me I can hit DEL and that launches the whole CMOS utility. There I can set the boot order so that the DVD is run first. But when I save and exit, I notice my keyboard is dead again. This time, the screen is showing things being set and loaded and I am prompted to hit any key to show I am sure that I want to boot from the DVD. I hit the Y key and I hit the spacebar, but it becomes clear that my input is ignored since my keyboard is being ignored. And the ol' Vista OS is loaded.

Please advise. Is there any way to set things up in the VISTA OS to force a boot from the DVD? I guess I can load the OS in save mode and format the C drive, but if I do that I might risk having a dead computer since the CMOS does not seem to be trusting enough to boot from the DVD drive even if you tell it to.

Microsoft has this page of links:
http://windows.microsoft.com/en-US/windows7/Installing-...

And then there is this link:
http://windows.microsoft.com/en-US/windows7/32-bit-and-...

And the Notes section specifies that I need boot off the DVD drive:
"•To install a 64-bit version of Windows 7 on a computer running a 32-bit version of Windows, you'll need to start, or boot, your computer using a 64-bit Windows 7 installation disc or files."

So, how do I make this happen?

When I completely power off and restart without going through CMOS, it seems to go further. The DVD player spins for a while, but in the end, after a few warning and error messages, it always comes to a point where it seems to prompt me if I am sure I want to boot off the DVD, the keyboard input is not recognized, and I return to my VISTA desktop.

Just to make sure that my hardware can handle 64-bit Windows 7, I checked out http://windows.microsoft.com/systemrequirements and Windows 7 system requirements and it says:

Quote:

If you want to run Windows 7 on your PC, here's what it takes:

• 1 gigahertz (GHz) or faster 32-bit (x86) or 64-bit (x64) processor
• 1 gigabyte (GB) RAM (32-bit) or 2 GB RAM (64-bit)
• 16 GB available hard disk space (32-bit) or 20 GB (64-bit)
• DirectX 9 graphics device with WDDM 1.0 or higher driver



I think I am good because this is what my system says:



The only thing that concerns me is "DirectX 9 graphics device with WDDM 1.0 or higher driver". If nothing else, can you help me find where I chan chcek on that?

More about : bit vista bit windows

a b $ Windows 7
May 6, 2012 6:23:43 PM

If your keyboard is usb make sure and check to make sure the keyboard and mouse are enabled and not disabled. Then proceed to boot from the DvD like you are trying to do.

A lot of motherboards disable mouse and keyboard by default.
m
0
l
a b $ Windows 7
May 6, 2012 6:24:54 PM

^ Check in the Bios ^
m
0
l
Related resources
!