Sign in with
Sign up | Sign in
Your question

KV-36XBR450 television - light blinks 4 times

Tags:
  • HDTV
  • TV
  • Light
  • Home Theatre
Last response: in Home Theatre
Share
March 9, 2010 6:28:53 PM

Does anyone know what code is assoicated with the following problem that occured on my television today March 9. 2010:

KV-36XBR450 television won't power on and the red light blinks 4 times. The TV never gave me any problems in the past. I purchased the TV in 2001-2002 time frame. Very nice tv and picture is great. Very heavy though. Thanks. pat

More about : 36xbr450 television light blinks times

March 9, 2010 6:38:24 PM

i unplugged the tv from the outlet and plugged it back in and the code went to 5 blinking lights. When the tv is povered on, you hear it coming on, but no picture is there. Thanks. Pat
m
0
l
a b x TV
March 11, 2010 8:16:57 PM

From http://www.techlore.com/article/15444/Understanding-Son...

Quote:
Many of the later model Sony TV’s have a built in self-diagnosis function. If the timer/standby indicator is blinking, this could be an indication of a problem with the unit. The diagnostic blinking will occur automatically with no action required by you to engage it.

The timing of the blinking you see would be as follows: two to nine blinks, (depending on the fault), about a third of a second apart, then a pause for 3 seconds, then the two to nine blinks about a third of a second apart again.

Here is a list of the problems that might have occurred indicated by the number of blinks. The words in parentheses are those, which you will see for each of these faults on a diagnosis screen described later in this article.

Unit is dead, No blinks - Problem in the standby power section. Might check fuse, R607, Q601, IC601, R612 and VDR601 (should show open).

Continuous blink once a second, no pausing - No reply from the jungle IC301 (data bus is busy, shorted to ground, or held high), IK video path is defective.

One blink - not used for the self-diagnosis

Two blinks - B+ over current protection (OCP), unit goes to the standby mode then displays the 2 blink fault. Could be a short in the power supply of any of the circuits.

Three blinks - B+ over voltage protection (OVP), unit goes to the standby mode then displays the 3 blink fault. This is also a problem in the power supply circuit, check T603 and R672.
Four blinks - No vertical Deflection (V STOP), Screen goes to a single horizontal line then the video signal muted. Check IC1509, Q1505

Five blinks - AKB circuit (automatic kine bias), the timer/standby indicator blinks for about 30 seconds then goes to the self-diagnosis function. Something is wrong with the video. Check video out, Q705, 732, 761 and other components on the C board, also check Q218, 219, 220 on the A board. In addition, unit could be in IK blanking, try turning up screen slightly.

Six blinks - No Horizontal (H STOP), no raster, goes to the blinking self-diagnosis function immediately. Check C515 & 516 and the jungle IC, IC206.

Seven blinks - High voltage shutdown. The high voltage has exceeded 33k and the unit goes immediately into safety shutdown. Check power supply regulation and horizontal circuits.

Eight blinks - Problem with the audio (AUDIO), unit goes to standby and blinks the self-diagnosis code. Check IC406 audio amp, PS401, and 402. On some projection models of Sony TV sets, this code means that T8005 (flyback transformer), or the associative components in the high voltage circuits are defective on the D board.


The article goes on to 10+ blinks, but I'm too blinkin' lazy to copy that much :D ...

PS - I use Bing almost exclusively now, and the above link was the top non-paid one for "Sony TV trouble codes"...
m
0
l
a b x TV
March 11, 2010 8:18:05 PM

^ Anyway, sounds like your circuit boards have gone bad - maybe lightning or other damage?
m
0
l
!