Display won't show when GPU is plugged into motherboard

[ViciousWafflez]

Long story short, my newly built PC works without the GPU with the motherboard through the HDMI cord.

However, when I put in the GPU into the motherboard I can't see any display. All I see is a black screen that says "No Signal".

When the GPU is plugged into the motherboard I can hear the fans spinning meaning that (to my knowledge) that is working.


My PC Build:

i3-6100 CPU @ 3.70GHz
GTX 1060 6GB
8GB of RAM
500W PSU EVGA 80+ Silver
Gigabyte H110M-A

 

[atljsf]

what gpu

 

[ViciousWafflez]

what gpu

GTX 1060 6GB

 

[kango69]

What GPU are you trying to use

 

[ViciousWafflez]

What GPU are you trying to use

GTX 1060 6GB

 

[vrumor]

Are you plugging into the GPU or the motherboard when you install your GPU? Make sure its plugged into the GPU.

 

[atljsf]

inserted properly into the slot and the 6 pin power cable connected to the gtx 1060?

 

[ViciousWafflez]

Are you plugging into the GPU or the motherboard when you install your GPU? Make sure its plugged into the GPU.

My GPU is in the motherboard with the fans rolling but there is no display. If I remove the GPU and leave it as the motherboard I'll see my display and everything'll be alright without a GPU.

 

[ViciousWafflez]

Are you plugging into the GPU or the motherboard when you install your GPU? Make sure its plugged into the GPU.

My GPU is in the motherboard with the fans rolling but there is no display. If I remove the GPU and leave it as the motherboard I'll see my display and everything'll be alright without a GPU.

 

[ViciousWafflez]

inserted properly into the slot and the 6 pin power cable connected to the gtx 1060?

It is properly connected. The GPU is running fine as I said. It's just that there is no display through the HDMI.

 

[atljsf]

you didn't answer if you connected the 6 pin power cable into the gpu

this cable

 

[kango69]

Can you try a differnent HDMI cable.
I had this problem before and It was the hdmi lead that caused it.

 

[ViciousWafflez]

you didn't answer if you connected the 6 pin power cable into the gpu

this cable

Yeah, it's connected into the GPU. Should I be downloading all of the MOBO drivers for it to work?

 

[ViciousWafflez]

Can you try a differnent HDMI cable.
I had this problem before and It was the hdmi lead that caused it.

I tried a different one and it didn't work. :/

 

[atljsf]

no, drivers go after the sysem boots, not before

try to reseat again the gpu into the pci express x16 slot that gpu, it must work or you got a bag gpu and you should rma that card

 

[ViciousWafflez]

no, drivers go after the sysem boots, not before

try to reseat again the gpu into the pci express x16 slot that gpu, it must work or you got a bag gpu and you should rma that card

I put it into the PCI express x16 and it doesn't work. Is there any other problem that there could be other than RMAing the card?

 

[atljsf]

rma mainboard

 

[kango69]

Turn the computer off then "Clear the CMOS", the jumper is right next to the front panel connector (page 4 manual)

 

[vrumor]

Are you plugging into the GPU or the motherboard when you install your GPU? Make sure its plugged into the GPU.

My GPU is in the motherboard with the fans rolling but there is no display. If I remove the GPU and leave it as the motherboard I'll see my display and everything'll be alright without a GPU.

This doesnt answer my question. Where is your HDMI cable plugged in to when the GPU is installed?