Reply to this thread
Forum question
Started by Zachary Roberts | | 12 answers
This person is having the exact same problem as me:
http://forum.corsair.com/v3/showthread.php?t=111863
This photo explains my situation rather well:
http://tinypic.com/view.php?pic=2ekm8ed&s=6
Basically, my 24-PIN ATX Connector won't go all the way in.
It goes about 50% of the way with ease, 40% with some force.
That makes 90%. The final 10% won't go in, even with force. :-/
It's a brand new motherboard and a brand new Power Supply.
I'm definitely inserting the connector the right way round though.
I also checked if pins were bent or if something was stuck..it isn't.
I spent 15-20 minutes yesterday trying to make it clip into place. :-/
I even placed two fingers underneath the MOBO to stop it bending.
That's how much pressure I was applying and it still wouldn't clip in.
If I push any more I'll break something so I stop. Any advice for me?
http://forum.corsair.com/v3/showthread.php?t=111863
This photo explains my situation rather well:
http://tinypic.com/view.php?pic=2ekm8ed&s=6
Basically, my 24-PIN ATX Connector won't go all the way in.
It goes about 50% of the way with ease, 40% with some force.
That makes 90%. The final 10% won't go in, even with force. :-/
It's a brand new motherboard and a brand new Power Supply.
I'm definitely inserting the connector the right way round though.
I also checked if pins were bent or if something was stuck..it isn't.
I spent 15-20 minutes yesterday trying to make it clip into place. :-/
I even placed two fingers underneath the MOBO to stop it bending.
That's how much pressure I was applying and it still wouldn't clip in.
If I push any more I'll break something so I stop. Any advice for me?
leowu
August 12, 2014 7:01:52 AM
I have same issue with Corsair CX430 I bought recently. MB is Asrock H97M Pro4, which is also a brand new. only 24pin connector has such an issue. I did clip it in once when I tried to test the MB, CPU and Mem without the case. But after I moved them into case, never succeeded.
Now pc is still working well. Any good approach to clip it in?
Now pc is still working well. Any good approach to clip it in?
Raul_McCai
April 4, 2014 1:43:13 PM
Agree with the post about supporting the back of the board after unscrewing it.
Disagree with any suggestion about using silicone lube.
Silicone is electrically conductive and it creeps and creeps and creeps until it spreads itself out one molecule thick so a drop could cover a vary large area.
If I absolutely had to use a lube on a board I'd try for one that is not conductive like cable pulling compound. But you won't need lube.
Disagree with any suggestion about using silicone lube.
Silicone is electrically conductive and it creeps and creeps and creeps until it spreads itself out one molecule thick so a drop could cover a vary large area.
If I absolutely had to use a lube on a board I'd try for one that is not conductive like cable pulling compound. But you won't need lube.
HenryTurle
April 4, 2014 9:55:36 AM
Zachary Roberts
January 22, 2014 12:07:09 AM
TheUltimateNoob123
January 21, 2014 2:10:31 PM
Zachary Roberts
January 21, 2014 2:07:53 PM
TheUltimateNoob123
January 21, 2014 1:10:06 PM
Zachary Roberts said:
Actually, with a bit of brute force it will go in eventually. I gave up as was afraid of bending the motherboard to the point of damaging something but someone else who has built computers in the past came along and just pushed it into place. The motherboard did bend and he did have to apply a lot of pressure but it did clip into place. No bending of the pins should be necessary, it's just sheer pressure you'll need and I'll admit it requires more pressure than I/you may be comfortable with applying...but apply it anyway and it will go in. ;-) Don't try and tweak the connector in any way as that might damage it.I did what you said and applied a lot of force, using my finger to stop the board from bending too much, and I've managed to get it extremely close to clipping in but it's refusing to move that last millimeter. I decided to see if it would show any signs of life so I plugged it in and turned on the psu and almost instantly the power light on the board lit up. Before I turn it all on I wanted to ask if anything would be damaged because the connector is still technically not all the way in?
TheUltimateNoob123
January 20, 2014 12:41:55 PM
Zachary Roberts
January 20, 2014 12:34:59 PM
Actually, with a bit of brute force it will go in eventually. I gave up as was afraid of bending the motherboard to the point of damaging something but someone else who has built computers in the past came along and just pushed it into place. The motherboard did bend and he did have to apply a lot of pressure but it did clip into place. No bending of the pins should be necessary, it's just sheer pressure you'll need and I'll admit it requires more pressure than I/you may be comfortable with applying...but apply it anyway and it will go in. ;-) Don't try and tweak the connector in any way as that might damage it.
TheUltimateNoob123
January 20, 2014 12:12:22 PM
I'm having exactly the same problem as you. I can get mine so that I only need to push it a few millimeters to clip on but no matter how hard I try it just won't go that extra 2 millimeters. The best way is to probably fiddle about a little with all the pins and then try. I'm going to try that aswell and I'll let you know if I get any results
See all answers