Sign in with
Sign up | Sign in

Reply to this thread

Solved Forum question

Started by Syblemz | | 15 answers
Water Cooling - Kit or Custom Build?
Hello,

I am going to get water cooling in my new build for the i7 4790K Devil's Canyon. I am in a CoolerMaster HAF X 942 case. I want a 3x120mm radiator on top. I don't really want a reservoir that takes up any 5.25" bays, but not too fussed. I would like it to be as silent as possible, and look awesome in the side panel window.

Should I get a kit such as one from xspc, or build a fully custom loop. In your answer, please give me pros and cons for both if you can. I'd be happy with either as far as I know at the moment.

If you say custom loop, please say why and name some good brands for each of the different parts to make up the loop.

I do not want a closed loop as I may cool the GPU in the future!

Thanks in advance!
  • By posting on this site, I confirm I am over 13 years of age and agree to abide by the site’s rules.

a b K Overclocking
a c 207 4 Gaming
a c 161 à CPUs
June 16, 2014 4:24:42 PM

Oh those are massive fans. Yeah it doesn't translate well in your image haha. But I would put the front, side, and rear as intake if you're going to mount a triple rad atop.
June 16, 2014 4:16:17 PM

ksham said:
What case is that? Doesn't look very optimal. It's a bad place to put your reservoir because you will have messy tube wiring going directly across your case. And the air intakes don't hit anywhere near the middle to top portion of your build. They're all located at the bottom of the case. So that configuration is suboptimal. I would use the rear as intake in that case because it's just needed. But I would highly recommend moving that reservoir to a better location.

When you start the actual build, you should ALWAYS plan it out as best as you can and make sure the tubing all works before you start screwing them in. Make sure you have room for the tubes and make sure your plans will work.

To be honest, I don't think that case is good for a water cool setup.


The case is a CoolerMaster HAF X 942. I cant change the case, I already have it. So, I'll use the back one as an intake and that will mean there will be 3 intake and 3 exhaust. I can still change to a cylinder reservoir if need be.

a b K Overclocking
a c 207 4 Gaming
a c 161 à CPUs
June 16, 2014 9:01:29 AM

What case is that? Doesn't look very optimal. It's a bad place to put your reservoir because you will have messy tube wiring going directly across your case. And the air intakes don't hit anywhere near the middle to top portion of your build. They're all located at the bottom of the case. So that configuration is suboptimal. I would use the rear as intake in that case because it's just needed. But I would highly recommend moving that reservoir to a better location.

When you start the actual build, you should ALWAYS plan it out as best as you can and make sure the tubing all works before you start screwing them in. Make sure you have room for the tubes and make sure your plans will work.

To be honest, I don't think that case is good for a water cool setup.
June 16, 2014 8:47:11 AM

ksham said:
I can't answer the pump question for kits. So sorry about that. But you need only ONE pump. Even if you have more than one GPU, you would still only require one pump.


Okay, thanks. Also, can you tell me if the air circulation is okay in this picture and in the gray circled area, should that be in or our air? Sorry about the messy writing. xD

http://gyazo.com/be5a36dd841433ee23483e32ba8db06a
a b K Overclocking
a c 207 4 Gaming
a c 161 à CPUs
June 16, 2014 8:32:13 AM

I can't answer the pump question for kits. So sorry about that. But you need only ONE pump. Even if you have more than one GPU, you would still only require one pump.
June 16, 2014 8:24:06 AM

C12Friedman said:
I've not been able to source individual parts for less than a kit so I base all my loops from kits. I'd suggest looking at the XSPC Photon D5 EX360 kit (a bit pricier than the bay res kits) The parts contained in the kits are of the same quality you'd otherwise purchase so I haven't found a down side to doing that. I suggest the XSPC kits since the Raystorm water block is one of the better blocks currently available.


I changed my mind and decided to go for the bay. Also, out of all their kits, what makes the raystorm water block better? And whats the better pump, the 750 or D5?

If I was thinking about adding a GPU into the loop, should I get the twin pump or would one do it fine?

Thanks

June 16, 2014 8:17:59 AM

ksham said:
Oh right, sorry forgot about the pump. I use Swiftech.

Edit: in terms of kits, I can't really answer the question to what is the best pump because I've only tried the D5 and that was short lived.


Okay, thanks.

a b K Overclocking
a c 207 4 Gaming
a c 161 à CPUs
June 16, 2014 8:10:57 AM

Oh right, sorry forgot about the pump. I use Swiftech.

Edit: in terms of kits, I can't really answer the question to what is the best pump because I've only tried the D5 and that was short lived.
June 16, 2014 8:09:26 AM

ksham said:
Uh no, just the blocks and fittings from Koolance. I used Alphacool radiators. Masterkleer or Primochill tubing. For the reservoir, I just pick one that I'm comfortable with but for my last build, I used Liquid Fusion for the style. Most of it is really for looks and less to do with functionality. So keep that in mind. It is NOT the best value/performance setup for all those parts.


Alright, I think I might just go for the kit as it's my first go at watercooling. What's the best pump from xspc, the 750 or D5? I changed my mind, I think I will just go for the 5.25" bay reservoir.

a b K Overclocking
a c 207 4 Gaming
a c 161 à CPUs
June 16, 2014 8:02:40 AM

Uh no, just the blocks and fittings from Koolance. I used Alphacool radiators. Masterkleer or Primochill tubing. For the reservoir, I just pick one that I'm comfortable with but for my last build, I used Liquid Fusion for the style. Most of it is really for looks and less to do with functionality. So keep that in mind. It is NOT the best value/performance setup for all those parts.

See all answers