Size, shape, and quality make the SG07 (B for black) a perfect alternative to the Shuttle cubes it competes against, while providing all of the benefits of non-proprietary component selection. The –W (windowed) version adds a little flair to the SG07B’s classic style.

SilverStone has not yet updated this model for USB 3.0 support. We hope this shortcoming will be addressed soon, as the company has recently added the feature to other, newer models.

SilverStone replaced its traditional crossflow fan mount with a solid steel panel, instead relying on an oversized intake fan and side vents to cool the CPU area.

Removing a medium-thickness one-piece steel lid reveals the company’s familiar 180 mm two-speed fan. We would have preferred to let the motherboard adjust fan speed in response to heat, though many ITX boards lack this capability. Configured as an intake fan that blows directly into the CPU cooler, a slide-out dust filter is included.
Also notice the space between the single 3.5” hard drive bay and the power supply. Designed to support two 2.5” drives side-by-side, we didn’t notice it until after the system was assembled.
The SG07B’s included 600 W power supply is 100% non-proprietary, exactly matching PS/2 form factor specifications typically reserved for ATX mid-towers. Those specifications include a 5.6” depth that many high-capacity power supplies now exceed, so replacement parts must be chosen carefully.
The SST-ST60F-SG provides 46 A of current on its single 12 V rail. That’s enough power to support any components that physically fit within the SG07 chassis.

An intake filter is also supplied for the power supply, but this one is secured with screws. The SG07 chassis uses vents on the side panel for power supply exhaust.

Opinion = Fact?
Anyway, I actually like Cubitek's case. Sure, it looks like it would be a pain to make changes to when doing upgrades or whatnot, but nothing is perfect. If it had a handle on top or something, Id probably use it for LAN parties and the such.
Otherwise, it was an interesting read.
Or 1 drive and a normal fan(take a bit of work.)
http://img842.imageshack.us/img842/1414/dsc0348n.jpg
1.) The motherboard used (as well as most other LGA 1155 boards) only has room for a 100mm cooler. For a 120mm cooler to fit, it has to be 10mm off-center, away from the graphics cards.
2.) Additional offset (more than 10mm) is required for any heat pipes that protrude from the "short" side.
Tom's Hardware should probably do a cooler roundup to figure out which low-profile designs actually fit this type of motherboard without blocking off the graphics card slot.
1.) The motherboard used (as well as most other LGA 1155 boards) only has room for a 100mm cooler. For a 120mm cooler to fit, it has to be 10mm off-center, away from the graphics cards.
2.) Additional offset (more than 10mm) is required for any heat pipes that protrude from the "short" side.
Tom's Hardware should probably do a cooler roundup to figure out which low-profile designs actually fit this type of motherboard without blocking off the graphics card slot.
Its an H55 board(H55N USB3), so same spacing as yours(or damn close)
AXP 140 fits without mods(unless there are components on the back of the board that get in the way)
Samuel 17 fits
It is said that the Shuriken(not the big shuriken) fits as well.
Or my first cooler for my MCE system. The stock Core2 cooler with bolts/nuts and rubber spacers.
http://img190.imageshack.us/img190/3787/dsc0225zv.jpg
I do think you should do a review for heatsinks that fit in SFF cases....
True, but seeing how much better it was might help people decide how much overclocking they can do.
I have a MSI GTX460 "Cyclone" installed in mine. It exhausts none of its heat, which I think limits how well the CPU can be cooled.
Another point to make is that the PSU can be mounted either way in the PC-Q08, either drawing its own air through the side vent, or helping to cool the CPU by pulling its air from inside the case.