- All(553952)
- Articles(3199)
- Forums(550753)
FILTERS
- AMD
- Intel
- Asus
- Gigabyte
- Motherboards
- CPUs
- BIOS
- Systems
- Graphics
- More
- Review
- News
- Reference
- How To
- Round-Up
- Past Week
- Past Month
- Past Year
- Custom Range
-
-
Should i update my bios if i am updating my os?
Oct 18, 2014 - in Forums
Last message : OP, no worries, glad to help. bsod1, no it is NOT recommended to update BIOS unless you absolutely need it. If not done correctly, it can render your MoBo unusable.
-
Upgrading And Repairing PCs 21st Edition: PC Diagnostics
Aug 10, 2014 - in Articles > Do It Yourself
BIOS POST Beep Codes, Checkpoint Codes, And Onscreen Messages BIOS POST Beep Codes Beep codes are used for fatal errors only, which are errors that occur so early in the process that the video card and other devices are not yet functional. Because no display is available, these codes take
PC Diagnostics, Testing, And Maintenance with specialized diagnostics software designed to test their particular functions. RAID adapters, for example, include configuration and diagnostic functions in the card’s ROM BIOS that you can access with a keystroke at boot time. Other devices
See more results
The Hardware Boot Process: Operating System Independent the Power_Good signal, which causes it to stop generating a reset signal to the microprocessor. The microprocessor begins executing the ROM BIOS code, starting at memory address FFFF:0000. Because this location is only 16 bytes from the very end
The POST -correcting code (ECC) memory is no longer available in most non-server chipsets, every PC still executes a POST when you turn it on. The following sections provide more detail on the POST, a series of program routines buried in the motherboard ROM-BIOS
Peripheral And Operating System Diagnostics them. Ensure that the system is free from malware such as viruses, rootkits, and spyware/adware. Check with the motherboard manufacturer to see if an updated BIOS is available. Make sure that the processor, expansion cards, memory modules
Windows 7/Vista And Windows 8 Startup -based versions of Windows is now replaced by the boot configuration data (BCD) store. The use of BCD enables a common interface for systems that use either traditional BIOS or the more recent extensible firmware interface (EFI) configuration methods
The Boot Process messages during the boot process: OS Independent Motherboard ROM BIOS Adapter card ROM BIOS extensions Master (partition) boot record (MBR) Volume boot record (VBR) OS Dependent System files Device drivers Programs run
DOS And Windows 9x/Me Boot Processes And Windows 2000/XP Startup .com gathers hardware configuration data and passes this information to Ntldr. If more than one hardware profile exists, Windows uses the correct one for the current configuration. If the ROM BIOS is ACPI compliant, Windows uses ACPI to enumerate
Passive Preventive Maintenance Procedures management to slow down the processor and other components when idle. In many cases you can still have the system enter Stand-By or Hibernate modes, as long as you have Wake-on-LAN enabled (check the BIOS Setup) so that the system can resume
Troubleshooting: Replacing Parts And The Bootstrap Approach has a speaker in the case) and boots up. Errors that display onscreen (nonfatal errors) and that do not lock up the system display a text message that varies according to BIOS type and version. Record any errors that occur and refer to the POST error
-
Stuck at BIOS screen after turned of power at the main
Oct 17, 2014 - in Forums
Last message : I cleared the CMOS and after restarting the computer it was still stuck at the BIOS screen. Could this be a problem with the motherboard?
-
My hard disk not detected by bios.
Oct 18, 2014 - in Forums
Last message : I have two hard disk one Hitachi and other Seagate. I have installed the windows 7 OS in Hitachi. When i connect the hitachi hard disk alone every thing is fine. But when i connect both the hard disk and boot the bios doesn't detect either
-
How to update BIOS?
Oct 17, 2014 - in Forums
Last message : I just built a new pc tonight. Using the Z97 Classified motherboard, there is a new BIOS update but I'm not sure how to do it. I remember on my last board using the .bin file from a USB Stick to do the update but I can't figure out how
-
Can't access BIOS! PLS HELP!
Oct 15, 2014 - in Forums
Last message : [quotemsg=14384072,0,445075]Reset the BIOS (read your motherboard manual for details, usually you pull the battery, or move a jumper), this should allow you to enter BIOS settings. what's a jumper (sorry, I'm a newb)
-
Sapphire Releases Performance-boosting BIOS for its R9-290
Nov 26, 2013 - in Articles > Graphics Cards
the same thing for its own R9-290, however, rather than releasing it in the form of a driver, it has released a new BIOS for the graphics card. While in practice you're unlikely to notice a difference between a driver fix or a BIOS fix
-
I updated my BIOS and now nothing shows up
Oct 17, 2014 - in Forums
Last message : Find the BIOS recovery file on the motherboard website for your specific motherboard and copy it to a USB flash drive. Then set the jumper on the motherboard to recover from a failed BIOS update (check your motherboard documentation
-
Asus p9x79 pro USB flashback bios button
Nov 7, 2013 - in Forums
Last message : and putting the CPU back in and it did nothing. So finally trying to update the bios using a USB flashback but the button doesn't light up and the motherboard doesn't respond. Anyone else have this problem or have a solution? Specifically speaking
-
Emachine EL1352g-41w Bios
Sep 23, 2014 - in Forums
Last message : [quotemsg=14236989,0,967910]Need the bios download for Emachine EL1352g-41w Bios, the website does not have one to download current one i have is P01-A3 i need the same one or newer one so i can reflash my bios in hopes to fix it. I been
- Next
-