The Final Three: Sub-$100 Cases For Your Gaming Build

Features
By Thomas Soderstrom
published

The journey was a long one, but we're finally wrapping up our round-up of sub-$100 gaming cases. Today we review the last three of 11 total product submissions and pick an overall favorite. The competition was vicious, but one model definitely stands out.

Building With The GT1

The GT1 supports 2.5” drives both within its trays and via a separate mount at the center partition of its hard drive cage, but we chose instead to use its top-panel hard drive dock. Doing so encourages us to take our data with us.

The GT1’s motherboard tray is barely large enough that we could have installed a 10.5”-wide motherboard, and our ATX-standard 9.625” board fits perfectly. Due to the tray’s open bottom and limited space between the tray and right-side panel, we stashed most of our cables behind its 5.25” bays.

Our only remaining installation issue was that we had to connect the auxiliary +12 V lead to our motherboard before screwing the board onto its standoffs. That’s because the tray slot that accommodates this cable is far to small to pass the connector through with the board already in place.

Blue lights at the top of the GT1 flash in unison with hard drive activity, and are unlit most of the time. Internal lighting comes from the case’s rear fan, and is color-matched to the red inserts we snapped into the front panel vents.

Thomas Soderstrom
Thomas Soderstrom
Thomas Soderstrom is a Senior Staff Editor at Tom's Hardware US. He tests and reviews cases, cooling, memory and motherboards.
46 Comments Comment from the forums
  • envy14tpe
    Thanks for doing the sub $100 cases. Obviously these are the most important ones.

    Is there any way tomshardware can put all the data together on a couple spreadsheets?
    Reply
  • JJ1217
    I'd like to see an article for this for cases that are larger, like the HAF X, Switch 810, and a few others. Be interesting to see them compared.
    Reply
  • Crashman
    11083777 said:
    Thanks for doing the sub $100 cases. Obviously these are the most important ones.

    Is there any way tomshardware can put all the data together on a couple spreadsheets?

    Performance data?
    http://www.tomshardware.com/reviews/antec-gx700-cooler-master-storm-scout-2-advanced-in-win-gt1,3512-10.html

    Or do you mean dimensional data?

    Reply
  • ojas
    Hey about the GX700: Only exhaust would mean more dust build up (negative internal air pressure) so how does that factor in?
    Reply
  • envy14tpe
    11083962 said:
    11083777 said:
    Thanks for doing the sub $100 cases. Obviously these are the most important ones.

    Is there any way tomshardware can put all the data together on a couple spreadsheets?

    Performance data?
    http://www.tomshardware.com/reviews/antec-gx700-cooler-master-storm-scout-2-advanced-in-win-gt1,3512-10.html

    Or do you mean dimensional data?
    That's exactly what I was looking for.
    Reply
  • vertexx
    Thanks for doing all the analysis. Cases are so subjective and have so many factors, and it all comes down to trade-offs.

    I thought the final analysis was perhaps a bit brief with so many cases reviewed. It would be good to see some type of point or rating system for different factors that go into overall case value (i.e. Finish Quality, Build Quality, Component Accessibility, Flexible Layout Options, Cable Management).
    Reply
  • Onus
    If one can deal with its anomalies (dealbreakers for some I'm sure), the Antec GX700 looks like a winner. I'm not sure about the styling, but that Ostrog does look like a good choice too. The Storm Scout looks like a bigtime value loser, and I'm very surprised Rosewill didn't do better. I suspect a lot of positions might change if you allow a certain amount of modding and tweaking though. I think this is why selecting a case will remain a matter of personal preference, regardless of what stock benchmarks show.
    Reply
  • Spooderman
    I built my friend's PC in the In Win and it was a good experience. Cable management was acceptable, everything fit nicely, nice color scheme. There was an interesting moment when I noticed that the case was built to include its own standoffs in the form of raised bumps on the motherboard tray. This scared me because I didn't trust putting the mobo on the case, but I looked it up and apparently the standoffs that came with the case were only for micro ATX. The front panel design and lights were nice looking and mostly unobtrusive. Other than that, it was a great case to build in and I think I'll be using it for my next friend's build this summer. Out of all the cases I would recommend this one for a good building experience.
    Reply
  • JPNpower
    So which is the good budget case that doesn't look like a flashy monster? I know it shouldn't matter, but I personally couldn't stand many of these cases sitting in my living room.
    Reply
  • Onus
    I'd take a look at Fractal Designs or Lian Li for a much more subdued styling, and also quiet. I don't mind a blue light here or there (if only to tell me the PC is on, ready to do as I tell it), but I don't like garish either; not in the living room anyway.
    Reply