The Final Three: Sub-$100 Cases For Your Gaming Build

By Thomas Soderstrom
published

The journey was a long one, but we're finally wrapping up our round-up of sub-$100 gaming cases. Today we review the last three of 11 total product submissions and pick an overall favorite. The competition was vicious, but one model definitely stands out.

In Win GT1

In Win’s GT1 doesn’t have room for a CPU power cable access hole, so the company adds a slot to the top of its CPU cooler support access hole. Using the slot requires builders to wrap the cable around the back of the motherboard tray, through the CPU cooler hole, and over the top of the motherboard before installing the motherboard.

Five of the GT1’s six hard drive bays have trays, and we verified on its webpage that the sixth tray is intentionally left out. You're instead expected to favor the 2.5” SSD mount found on the cage’s center divider.

The GT1’s top-panel hard drive/SSD dock uses SATA power, but that doesn’t alleviate its need for an older four-pin power supply lead. Its built-in fan controller uses a four-pin hard drive power connector and outputs exclusively to fans that use the same dated Molex connector.

Standoffs that are pressed into the motherboard tray support ATX motherboards, so the GT1’s installation kit includes only those needed to adapt it to microATX motherboards. It also has enough large screws for the motherboard, a power supply, and two cards.

A set of small screws for 2.5” drives is also included, along with three cable ties and a pack of red trim rings to dress up front-panel vents.

Thomas Soderstrom
Thomas Soderstrom
Thomas Soderstrom is a Senior Staff Editor at Tom's Hardware US. He tests and reviews cases, cooling, memory and motherboards.
46 Comments Comment from the forums
  • envy14tpe
    Thanks for doing the sub $100 cases. Obviously these are the most important ones.

    Is there any way tomshardware can put all the data together on a couple spreadsheets?
    Reply
  • JJ1217
    I'd like to see an article for this for cases that are larger, like the HAF X, Switch 810, and a few others. Be interesting to see them compared.
    Reply
  • Crashman
    11083777 said:
    Thanks for doing the sub $100 cases. Obviously these are the most important ones.

    Is there any way tomshardware can put all the data together on a couple spreadsheets?

    Performance data?
    http://www.tomshardware.com/reviews/antec-gx700-cooler-master-storm-scout-2-advanced-in-win-gt1,3512-10.html

    Or do you mean dimensional data?

    Reply
  • ojas
    Hey about the GX700: Only exhaust would mean more dust build up (negative internal air pressure) so how does that factor in?
    Reply
  • envy14tpe
    11083962 said:
    11083777 said:
    Thanks for doing the sub $100 cases. Obviously these are the most important ones.

    Is there any way tomshardware can put all the data together on a couple spreadsheets?

    Performance data?
    http://www.tomshardware.com/reviews/antec-gx700-cooler-master-storm-scout-2-advanced-in-win-gt1,3512-10.html

    Or do you mean dimensional data?
    That's exactly what I was looking for.
    Reply
  • vertexx
    Thanks for doing all the analysis. Cases are so subjective and have so many factors, and it all comes down to trade-offs.

    I thought the final analysis was perhaps a bit brief with so many cases reviewed. It would be good to see some type of point or rating system for different factors that go into overall case value (i.e. Finish Quality, Build Quality, Component Accessibility, Flexible Layout Options, Cable Management).
    Reply
  • Onus
    If one can deal with its anomalies (dealbreakers for some I'm sure), the Antec GX700 looks like a winner. I'm not sure about the styling, but that Ostrog does look like a good choice too. The Storm Scout looks like a bigtime value loser, and I'm very surprised Rosewill didn't do better. I suspect a lot of positions might change if you allow a certain amount of modding and tweaking though. I think this is why selecting a case will remain a matter of personal preference, regardless of what stock benchmarks show.
    Reply
  • Spooderman
    I built my friend's PC in the In Win and it was a good experience. Cable management was acceptable, everything fit nicely, nice color scheme. There was an interesting moment when I noticed that the case was built to include its own standoffs in the form of raised bumps on the motherboard tray. This scared me because I didn't trust putting the mobo on the case, but I looked it up and apparently the standoffs that came with the case were only for micro ATX. The front panel design and lights were nice looking and mostly unobtrusive. Other than that, it was a great case to build in and I think I'll be using it for my next friend's build this summer. Out of all the cases I would recommend this one for a good building experience.
    Reply
  • JPNpower
    So which is the good budget case that doesn't look like a flashy monster? I know it shouldn't matter, but I personally couldn't stand many of these cases sitting in my living room.
    Reply
  • Onus
    I'd take a look at Fractal Designs or Lian Li for a much more subdued styling, and also quiet. I don't mind a blue light here or there (if only to tell me the PC is on, ready to do as I tell it), but I don't like garish either; not in the living room anyway.
    Reply