Software: The Digital Profile
In the “Digital Profile,” under the keyboard GUI is “General keyboard settings.” Here, you can change the actuation point of the switches with a simple slider. You’ll note that this range is limited to 1.5-4mm, and it may also occur to you that an actuation point of 4mm on a switch that has a total travel of 4mm is...stupid and pointless. The range is there simply because that’s the range of analog sensing, and instead of trying to handicap the actuation point in the Digital Profile, Wooting left the range alone.
We’ve written before about why the analog range on Flaretech switches doesn’t begin until 1.8mm into the travel. In (very) short, it’s this:
The way the optical sensing is done on the desktop Flaretech Prism switch is that a light beam, pointing up from the PCB, gets shot across the opening of the switch shaft. When you press the key, the switch stem descends, and when the prism interrupts the beam, it gets bent 90 degrees, down to the photo sensor (which is also mounted on the PCB).
Astute readers will notice, though, that the switch specifications claim an analog range of 1.8-3.6mm, which conflicts with the Wootility’s 1.5-4mm slider. So what gives? Wooting told Tom’s Hardware that the precise beginning and end of the analog range depends on the keyID and switch. (This of course makes sense; all mechanical switches have certain manufacturing tolerances, and these switches are no different.) The analog range on these Flaretech switches, we’re told, begins anywhere from about 1.5-1.8mm and ends around 3.5-3.8mm.
Wooting said that no matter what, the sliders will always give you a slightly relative range, but it’s continuing to refine its manufacturing processes to get increasingly accurate.
That’s all fair, although it would perhaps be less confusing to users if the sliders were limited to that 1.5-3.8mm range instead of expanding all the way to 4mm.
In any case, it’s worth noting that being able to program the actuation point to anywhere within the normal pretravel range of most switches on the market--about 1.5-2.2mm--is a marvelous customization feature.
Below the actuation point slider is the Function Toggle. As we mentioned, some of the keys on the Wooting One serve double duty as media keys and lighting controls. Pressing Fn+[key] also switches between profiles, by default. (You can also toggle between the Digital Profile and one analog profile by pressing the Mode key in the upper right corner of the One.)
By flipping on the toggle, you enable a Fn layer so you don’t have to press Fn first. In other words, the Fn toggle turns double-duty keys into dedicated media, lighting, and profile switching keys. This would be handy if, for example, you prefer having dedicated media controls instead of the Home, Pg Up, Pg Dn, etc. keys.
That brings us to the Keybindings area. This is where you can see the key bindings that you use to switch between profiles. These are easily changed; click the button(s) on the right (Mode, FN key, etc.) and press any key (but not a key combination) to create a new binding. Click “Save to keyboard.” It’s that simple.
At the bottom of the Digital Profile section is the “DKS,” or double keystroke feature. Simply put, this allows you to program two commands to a single keystroke--essentially two actuation points within one stroke--and you can use the slider to set actuation points for both. This short video explains it nicely and succinctly:
Obviously, the feature has limitations. Although the “qQ” example in the video does a nice job showing how it works, using the feature for something like capitalization is obviously useless because to get to the capital Q you have to first get through the lowercase q. It’s like sharing a drink with someone, guzzling it all, and saying that you had to drink through their half on top to get to yours on the bottom.
In games, though, it has some use, and you can actually use it as a sort of de facto analog input in some cases, and also as a de facto macro tool. Both have significant limitations, but if you get creative, there’s a lot you can do.
The example in the video is using the same key to perform normal or quick casting as well as smart casting in League of Legends. Press partway down and hit the normal/quick casting, and press down further to perform smart casting.
In that same vein, if you want to put walking and sprinting on one key (like you can in analog mode), you can program the top part of the press to “W” and the bottom part to Shift + W. Or if you’re one of those people who likes to bind diagonal movement to Q or E instead of having to press W+A or W+D,you could use this feature to program the A key thusly: First actuation = A, secondary actuation = A + W.
You get the idea.
You can set the actuation point for either action anywhere between 1.5-4mm, which, as we noted above, is actually going to be within the 1.5-3.8mm range. Obviously you need to use common sense there so as to leave yourself enough travel for the feature to work. For example, you probably want to bind the first actuation point at 1.5mm and the other at, say, 3.5mm. By default, the first is set to 1.7mm, and the second is at 3.8mm (But hey, you do you.)
Note that you can bind a maximum of two keys per actuation point, and you can’t bind any mouse functions to any of them. The DKS feature is absent on the three Analog profiles.
MORE: Best Deals
MORE: All Keyboard Content