Why you can trust Tom's Hardware Our expert reviewers spend hours testing and comparing products and services so you can choose the best for you. Find out more about how we test.

Page 6 of 11:

Protection Features

Check out our PSUs 101 article to learn more about PSU protection features. Our protection features evaluation methodology is described in detail here.

Swipe to scroll horizontally

Protection Features
OCP	12V: ✗ 5V: 37A (148%) 3.3V: 36.1A (144.4%) 5VSB: 4.6A (153.3%)
OPP	793.541W (122.1%)
OTP	✓ (155°C @ Secondary side)
SCP	12V: ✓ 5V: ✓ 3.3V: ✓ 5VSB: ✓ -12V: ✓
PWR_OK	Operates properly
NLO	✓
SIP	Surge: MOV Inrush: NTC thermistor

The OCP triggering points on the minor rails are set high, while over-power protection kicks in at around 122% of the PSU's maximum power output; it's configured properly.

We didn't find anything to indicate whether the PR-BP0650-SM has OTP or not, but we tortured it with our heat gun and finally got the PSU to switch off at around 155°C on its secondary side. This is a very high temperature; we'd normally want it 20-30°C lower.

Finally, the power-good signal is accurate, though as we mentioned the hold-up time is very low.

MORE: Best Power Supplies

MORE: How We Test Power Supplies

MORE: All Power Supply Content

Current page: Protection Features

Prev Page Efficiency, Temperature & Noise Next Page Cross-Load Tests & Infrared Images

See more Power Supplies Reviews

Aris Mpitziopoulos is a contributing editor at Tom's Hardware, covering PSUs.

Intel stealthily pulls the plug on Deep Link less than 5 years after launch

Gigabyte incorporates 64MB BIOS chip on X870 motherboard to integrate the WiFi driver

Save close to $250 on this 2024 Apple iMac with an M4 CPU

See more latest

10 Comments Comment from the forums

turkey3_scratch

I don't think it's so much the aggressiveness of the fan that contributes to the noise rather than the fact that it's just a noisy fan. There are many other fans that could be spinning at equal RPM and be much quieter while providing the same amount of cooling.
Then again, the noise should not be too severe of a deal in a computer case with other fans (such as case fans at 100% always) contributing more significantly to the net noise.

Edit: Nevermind, dope move by me. I didn't realize the y axis started at 1400RPM, yep, that fan RPM is very high indeed.
Reply
Ne0Wolf7

20135612 said:
I don't think it's so much the aggressiveness of the fan that contributes to the noise rather than the fact that it's just a noisy fan. There are many other fans that could be spinning at equal RPM and be much quieter while providing the same amount of cooling.

Then again, the noise should not be too severe of a deal in a computer case with other fans (such as case fans at 100% always) contributing more significantly to the net noise.

I agree, especially when you're like me and have six of them because you were obsessed with filling all of the fan slots on your first build (lol). When the noise finally got to me, I got creative with my intake/ output configuration, and set my PSU to ECO mode (which is no fan). The PSU started roasting, so I rebooted with the fan going and noticed no noise difference whatsoever and the PSU was much cooler (then again, my case fans are sleeve bearing, but still).
Reply
turkey3_scratch

20135670 said:
20135612 said:
I don't think it's so much the aggressiveness of the fan that contributes to the noise rather than the fact that it's just a noisy fan. There are many other fans that could be spinning at equal RPM and be much quieter while providing the same amount of cooling.

Then again, the noise should not be too severe of a deal in a computer case with other fans (such as case fans at 100% always) contributing more significantly to the net noise.

I agree, especially when you're like me and have six of them because you were obsessed with filling all of the fan slots on your first build (lol). When the noise finally got to me, I got creative with my intake/ output configuration, and set my PSU to ECO mode (which is no fan). The PSU started roasting, so I rebooted with the fan going and noticed no noise difference whatsoever and the PSU was much cooler (then again, my case fans are sleeve bearing, but still).

I have a build with like 6 fans that gets noisy because the motherboard only supports so many fans, so I have to plug them into the PSU. But I also have a second build that is dead silent with some Noctuas, and that's the type of build I would want a very silent or at least semi-passive PSU in.
Reply
Ne0Wolf7

20135678 said:
20135670 said:
20135612 said:
I don't think it's so much the aggressiveness of the fan that contributes to the noise rather than the fact that it's just a noisy fan. There are many other fans that could be spinning at equal RPM and be much quieter while providing the same amount of cooling.

Then again, the noise should not be too severe of a deal in a computer case with other fans (such as case fans at 100% always) contributing more significantly to the net noise.

I agree, especially when you're like me and have six of them because you were obsessed with filling all of the fan slots on your first build (lol). When the noise finally got to me, I got creative with my intake/ output configuration, and set my PSU to ECO mode (which is no fan). The PSU started roasting, so I rebooted with the fan going and noticed no noise difference whatsoever and the PSU was much cooler (then again, my case fans are sleeve bearing, but still).

I have a build with like 6 fans that gets noisy because the motherboard only supports so many fans, so I have to plug them into the PSU. But I also have a second build that is dead silent with some Noctuas, and that's the type of build I would want a very silent or at least semi-passive PSU in.
My ATX motherboard only has two fan headers, not sure who was in charge there, haha, but I bought two three way splitters so I could control the speeds. My side panel has two fan slots, and I can only use one of them because the CPU cooler, so I just have this lovely outlet for sound... Its really a blessing too beacsue I have two GPUs so one can never be tarved for air too much but still. A new case and fans are in my future somewhere.
Reply
takeshi7

Can you review the Rosewill Hive 750W? I got one on sale for $60 recently and there aren't any recent reviews for it, and not from any that are as in depth as Tom's Hardware.
Reply
James Mason

@takeshi7, there aren't new reviews for it because it isn't a new PSU.
Reply
takeshi7

20143641 said:
@takeshi7, there aren't new reviews for it because it isn't a new PSU.
It's still relevant though. Especially because it's cheaper, more powerful, and has the same 80 Plus rating as this Riotoro unit.
Reply
turkey3_scratch

20144799 said:
20143641 said:
@takeshi7, there aren't new reviews for it because it isn't a new PSU.
It's still relevant though. Especially because it's cheaper, more powerful, and has the same 80 Plus rating as this Riotoro unit.

"More powerful" can be interpreted many ways. What do you mean by that?
Reply
takeshi7

20144830 said:
20144799 said:
20143641 said:
@takeshi7, there aren't new reviews for it because it isn't a new PSU.
It's still relevant though. Especially because it's cheaper, more powerful, and has the same 80 Plus rating as this Riotoro unit.

"More powerful" can be interpreted many ways. What do you mean by that?
I mean 750W > 650W.
Reply
turkey3_scratch

20144901 said:
20144830 said:
20144799 said:
20143641 said:
@takeshi7, there aren't new reviews for it because it isn't a new PSU.
It's still relevant though. Especially because it's cheaper, more powerful, and has the same 80 Plus rating as this Riotoro unit.

"More powerful" can be interpreted many ways. What do you mean by that?
I mean 750W > 650W.

Eh, doesn't really mean much of anything if you ask me. It's just what they decided to rate it at. I don't think we'll ever see a Rosewill Hive review. They're older and newer units get reviewed instead.

A high quality lower wattage power supply can be more powerful than a lesser quality higher wattage power supply.
Reply