Skip to main content

Part 1: Four Gaming Enclosures Under $50

Inside The ECA3171-BR-AP

Our investigation into what comprises the ECA3171-BR-AP begins with its ECA3170-family chassis. A 120 mm front fan accompanies all versions, yet this otherwise modern looking chassis does not include the convenience of an access hole for installing CPU cooler support plates.

The front fan of all –BR versions has red blades and LEDs. Note that, while the drive cage supports two 3.5” external drives, the lower of these two bays is blocked off at the front panel.

A card clip disengages all cards simultaneously, presenting a slight inconvenience for some multi-card builds. Yet, this is the only screw-free mechanism that works with many of our graphics cards, and those who can’t use it will find that it’s removable using a screwdriver.

Unique to the EC3171-BR-AP are two 120 mm red LED fans factory-installed on the side panel. Users who prefer to choose their own fans will find that models up to 140 mm fit.

  • rzilla91
    Great article!
    I have the Antec 300 and love it - my current build is/was my first build, and the Antec case was very easy to build in.

    My only (rather silly) question is how did you get the case fans to run on low? They appear to be plugged into your PSU, which is what i did, but that forces it to run on high.
    Reply
  • falchard
    I think the Antec 300 and AeroCool models lose for 1 simple reason. They cannot house the longer ATI HD5850~HD5970.
    Reply
  • gkay09
    ^ Did you read the Aerocool specs properly ? Card Length - 17.7"
    AFAIK there are no graphic cards that are longer than 12.5", so it would fit HD 5970...
    But as for the 300, I doubt it wont fit the 5970, but other cards would...
    But if you will be spending ~$600 for a graphic card, then am sure you wont skimp on the case...
    Reply
  • Mark Heath
    Interesting to see the Antec 300 doing well even when the fan speed's put to low.
    Reply
  • smithereen
    No NZXT Beta?
    Reply
  • rzilla91Great article!I have the Antec 300 and love it - my current build is/was my first build, and the Antec case was very easy to build in.My only (rather silly) question is how did you get the case fans to run on low? They appear to be plugged into your PSU, which is what i did, but that forces it to run on high.It should be equiped with speed-adjustmentable tri-cool fans, which should have added speed selectors to go from LOW to MID or HI, and back.
    Reply
  • falchard
    I just reread the card length on the AeroCool.
    I would like a review on the NZXT Beta. Sub $50 market, you really aren't looking at any of those cases. You are looking at the Rosewills, NZXT, and cheap Thermaltakes.
    Reply
  • @falchard - My Vapor-X 5850 fit perfectly in my Antec 300. I don't know what you're BSing about.
    Reply
  • rajangel
    I own the 300. It's a nice sturdy case, but in the end it really was a pain in the rear to put it all together. It's extremely cramped.

    @falchard-
    Also don't ever buy Rosewill. EVER. Their products are terrible. I've bought a few items they've had on clearance (from newegg) and not a single product is worth the 90% discount. One case came bent and the power supply inside was missing some of the power plugs the manual said it had. One item came shipped with a driver all in Chinese. Customer service blamed it on whoever shipped it (right because Newegg is going to switch the power supply inside a case). Newegg switched the case out and the girl on the phone said they have a lot of problem with Rosewill products. The laptop pad was missing fan blades.

    Reply
  • falchard
    Well thats your problem right there, you are looking at Rosewill for electronic products. You shop Rosewill for products that don't rely on electricity like a case.
    Reply