Why you can trust Tom's Hardware Our expert reviewers spend hours testing and comparing products and services so you can choose the best for you. Find out more about how we test.
Transient Response Tests
Advanced Transient Response Tests
For details on our transient response testing, please click here.
In these tests, we monitored the response of the PSU in two different scenarios. First, a transient load (10A at +12V, 5A at 5V, 5A at 3.3V and 0.5A at 5VSB) was applied to the PSU for 200 milliseconds while the PSU was working at 20 percent load. In the second scenario, the PSU was hit by the same transient load while operating at 50 percent load. In both tests, we used our oscilloscope to measure the voltage drops caused by the transient load. The voltages should have remained within the ATX specification's regulation limits.
These tests are crucial because they simulate the transient loads a PSU is likely to handle (such as booting a RAID array or an instant 100 percent load of CPU/GPUs). We call these tests Advanced Transient Response Tests, and they are designed to be very tough to master, especially for a PSU with a capacity of less than 500W.
Advanced Transient Response at 20 Percent
| Voltage | Before | After | Change | Pass/Fail |
|---|---|---|---|---|
| 12V | 12.086V | 11.986V | 0.83% | Pass |
| 5V | 5.077V | 4.962V | 2.27% | Pass |
| 3.3V | 3.381V | 3.189V | 5.68% | Pass |
| 5VSB | 5.059V | 5.006V | 1.05% | Pass |
Advanced Transient Response at 50 Percent
| Voltage | Before | After | Change | Pass/Fail |
|---|---|---|---|---|
| 12V | 11.981V | 11.874V | 0.89% | Pass |
| 5V | 5.042V | 4.911V | 2.60% | Pass |
| 3.3V | 3.376V | 3.178V | 5.86% | Pass |
| 5VSB | 5.020V | 4.969V | 1.02% | Pass |
The +12V rail performed pretty well with transient loads, while the 5V and 5VSB rails encountered controlled voltage drops in our two scenarios. The weak spot was the 3.3V rail, which registered a huge deviation in both tests. However, it managed to keep its voltage within the ATX spec's specified range.
Here are the oscilloscope screenshots we took during Advanced Transient Response Testing:
Transient Response At 20 Percent Load
Transient Response At 50 Percent Load
Turn-On Transient Tests
In the next set of tests, we measured the response of the PSU in simpler transient load scenarios during the PSU's power-on phase.
For the first measurement, we turned off the PSU, dialed in the maximum current the 5VSB could output and switched it back on. In the second test, we dialed the maximum load the +12V could handle and started the PSU while it was in standby mode. In the last test, while the PSU was completely switched off (we cut off the power or switched off the PSU by flipping its on/off switch), we dialed the maximum load the +12V rail could handle before switching on the PSU from the loader and restoring the power. The ATX specification states that recorded spikes on all rails should not exceed 10 percent of their nominal values (+10 percent for 12V is 13.2V, and 5.5V for 5V).
We didn't notice any spikes or voltage overshoots here. The VPF650 performed very well in these tests.
EKWB issues public apology regarding delayed payments — promises employees and suppliers it will change its ways
Noctua releases low-profile CPU cooler for SFF builds — NH-L12Sx77 has better clearance for RAM, VRM heatsinks
Chinese may be evading Nvidia GPU sanctions with Dell, Gigabyte, and Supermicro servers: Report
